Fisher 9500の取扱説明書

16ページ 0.17 mb
ダウンロード

ページに移動 of 16

Summary
  • Fisher 9500 - page 1

    www.Fisher.com D100380X012 Type 9 500 B utterfly C ontrol V alve Contents Introduction 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of Manual 1 . . . . . . . . . . . . . . . . . . . . . . . . . Description 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation 2 . . . . . . . . . . . . . . . . . . . . . ...

  • Fisher 9500 - page 2

    9500 Valve Instruction Manual Form 2433 November 2007 2 Table 1. Specifications Valve Sizes NPS J 2, J 3, J 4, J 6, J 8, J 10, or J 12 Valve Body Style Flangeless (wafer-type) valve body to be installed between pipeline flanges End Connection Styles Flangeless (wafer-style) valve body mates with CL125 flat-face flanges per ASME B16.1, with CL150 an ...

  • Fisher 9500 - page 3

    9500 Valve Instruction Manual Form 2433 November 2007 3 that must be taken to protect against process media. If installing into an existing application, also refer to the WARNING at the beginning of the Maintenance section in this instruction manual. These valves may be installed in many positions by referring to the Actuator Mounting procedures an ...

  • Fisher 9500 - page 4

    9500 Valve Instruction Manual Form 2433 November 2007 4 Figure 2. Valve Shaft Marking A2755-1/IL LOCATION OF INDEX MARK ON END OF VALVE SHAFT TAIL OF Fishtail DISC LOCATION OF FLAT SPOT ON VALVE SHAFT NOSE OR LEADING EDGE OF DISC OPEN FLOW WITH SPLINED VALVE SHAFT EQUAL MEASUREMENTS BETWEEN VALVE FACE AND DISC EDGE AT TOP AND BOTTOM ENSURE FULLY CL ...

  • Fisher 9500 - page 5

    9500 Valve Instruction Manual Form 2433 November 2007 5 result if the partial O-ring faces are not properly supported. Do not use flanges having an inside diameter larger than the maximum shown in table 3. The NPS 6 to 10 sizes must not be used with slip-on flanges unless flange adaptors are used to support the liner. When using slip-on flanges wit ...

  • Fisher 9500 - page 6

    9500 Valve Instruction Manual Form 2433 November 2007 6 leakage downstream (between the bushings and disc hubs) may also indicate a need for hub seal adjustment. To adjust the hub seals: 1. Tighten both thrust-plate cap screws (key 10) 1/4 turn on one side (the side where shaft leakage is occurring). CAUTION To avoid excessive side thrust on the di ...

  • Fisher 9500 - page 7

    9500 Valve Instruction Manual Form 2433 November 2007 7 Figure 5. Tandem Linkage Adjustment for Three-Way Valve Assemblies B2144-1 / IL locknuts on the tandem linkage when adjustment is complete. Maintenance Use table 4 to locate and correct possible leakage or mechanical linkage problems with the valve. W ARNING Avoid personal injury from sudden r ...

  • Fisher 9500 - page 8

    9500 Valve Instruction Manual Form 2433 November 2007 8 Table 4. Troubleshooting Guide Fault Possible Cause Correction 1. Leakage out sides of valve (at thrust plates) between thrust bushings and shaft. a. Hub seals require adjustment. b. Taper pins are not sealed. a. Adjust using Hub Seals portion of Adjustments procedures. b. Remove valve from li ...

  • Fisher 9500 - page 9

    9500 Valve Instruction Manual Form 2433 November 2007 9 Table 5. Taper Pin Details for 9500 Series Valves VALVE SIZE, NPS SHAFT DIAMETER mm (Inches) AMERICAN STANDARD TAPER PIN SIZE DRILL SIZE 2 3, 4 12.7 (1/2) 15.9 (5/8) 2 3 #20 (0.161 Inches) #16 (0.177 Inches) 6 8, 10 12 19.1 (3/4) 25.4 (1) 31.8 (1-1/4) 4 6 7 13/64 Inches 9/32 Inches 21/64 Inche ...

  • Fisher 9500 - page 10

    9500 Valve Instruction Manual Form 2433 November 2007 10 b. If installing a new shaft, insert the new shaft into the valve body and disc. Measure between the valve body and the splined end of the shaft. Make certain that the distance is correct to engage the actuator coupling lever. Be certain that the flat spot or index mark on the end of the shaf ...

  • Fisher 9500 - page 11

    9500 Valve Instruction Manual Form 2433 November 2007 11 Figure 6. Splined-Shaft Index Mark Alignment for Standard Mounting Position-Valve Action Combinations 54A3246-B B1054-3*/IL 14A7222-A 54A3246-B A1837-3/IL ...

  • Fisher 9500 - page 12

    9500 Valve Instruction Manual Form 2433 November 2007 12 1. Refer to the appropriate actuator instruction manual for assistance in disconnecting and removing the actuator lever. Avoid disturbing the actuator turnbuckle adjustment, if possible. 2. If the valve disc is a Fishtail disc, rotate the disc 180 degrees from the original position. 3. Positi ...

  • Fisher 9500 - page 13

    9500 Valve Instruction Manual Form 2433 November 2007 13 Parts List Note Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson Process Management sales office. Key Description Part Number 1 Valve Body If you need a valve body as a replacement part, order by valve size, serial number, and desired materi ...

  • Fisher 9500 - page 14

    9500 Valve Instruction Manual Form 2433 November 2007 14 Figure 7. Type 9500 Valve Body Assembly G34171-B/DOC Key Description Part Number 15* Taper Pin (2 req’d) (continued) S17400 (17-4 PH) NPS 2 F1368135362 NPS 3 G1194435362 NPS 4 G1194235362 NPS 6 G1194035362 NPS 8 G1193835362 NPS 10 G1329135362 NPS 12 H1374835362 S20910 NPS 2 F13681K0022 NPS ...

  • Fisher 9500 - page 15

    9500 Valve Instruction Manual Form 2433 November 2007 15 ...

  • Fisher 9500 - page 16

    9500 Valve Instruction Manual Form 2433 November 2007 16 Emerson Process Management Marshalltown, Iowa 50158 USA Cernay 68700 France Sao Paulo 05424 Brazil Singapore 128461 www.Fisher.com The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be ...

メーカー Fisher カテゴリー Plumbing Product

Fisher 9500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 9500の取扱説明書
- Fisherの製品カード
- パンフレット
- またはFisher 9500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Fisher 9500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Fisher 9500の取り付け説明書、サービスマニュアル、簡易説明書、またはFisher 9500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Fisher 9500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Fisher 9500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがFisher 9500を使用するのを助ける技術的文書のことです。説明書は通常、全てのFisher 9500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Fisherの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Fisher 9500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははFisher 9500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Fisher 9500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Fisher 9500デバイスの基本機能を使うにあたってのヒント。 Fisher 9500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Fisher 9500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるFisher 9500のメーカー/サービスへの連絡先に関する情報。

Fisher 9500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもFisher 9500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがFisher 9500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)