Dixon 8000Dの取扱説明書

44ページ 0.71 mb
ダウンロード

ページに移動 of 44

Summary
  • Dixon 8000D - page 1

    8000D SERIES 2003 OPERATORS MANUAL ...

  • Dixon 8000D - page 2

    IMPORTANT - READ CAREFULLY The Dixon ® ZTR ® Mower is both easy and fun to operate. However, any power mower must be operated properly to be safe. It is not a toy or a recreational vehicle. Before you start to use the mower, read the operators manual carefully and become completely familiar with the controls. The information contained in this ...

  • Dixon 8000D - page 3

    3 INDEX Page Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Warranty Policy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14-18 Operation ...

  • Dixon 8000D - page 4

    4 RIDING LAWN MOWERS, IF IMPROPERLY OPERATED, CAN CAUSE SERIOUS INJURY OR DEATH. The most common causes of injury to the operator or bystander... ...read and understand this manual to prevent injuries. BLADE CONTACT TIP OVER RUN OVER BACK OVER SAFETY ...

  • Dixon 8000D - page 5

    5 Safety Alert Symbol When you see this symbol, BE ALERT to the potential for injury. DANGER (highlighted in red) indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING (highlighted in orange) indicates a potentially hazardous situation which, if not avoided, could result in death or serio ...

  • Dixon 8000D - page 6

    6 Failure to observe the following safety instructions could result in serious injury or death. GENERAL OPERATION:  Read, understand, and follow all instructions in the manual and on the mower before starting. Only allow responsible adults, who are familiar with the instructions, to operate the mower. Clear the area of objects such as rock ...

  • Dixon 8000D - page 7

    7 GENERAL OPERATION (continued): Turn off blades when not mowing. Stop engine before removing grass catcher or unclogging chute. Mow only in daylight or good artificial light. Do not operate the mower while under the influence of alcohol or drugs. Watch for traffic when operating near or crossing roadways. Use extra care when load ...

  • Dixon 8000D - page 8

    8 SLOPE OPERATION: Slopes are a major factor related to loss-of-control and tip-over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope or if you feel uneasy on it, do not mow it ! DO  Mow across the slope with your Dixon ZTR - never up or down.  Remove obstacles such as ro ...

  • Dixon 8000D - page 9

    9 SAFETY CHILDREN: Tragic accidents can occur if the operator is not alert to the presence of children. Children are attracted to lawn mowers and the mowing activity. NEVER assume children will stay where they were last seen. Be alert to avoid accidents.  Keep children out of the mowing area and under the watchful care of another responsible adu ...

  • Dixon 8000D - page 10

    10 SERVICE:  Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive. Use only an approved container. Never remove fuel cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke while refueling. Never refuel the mower indoors. Never store the mower or fuel container inside a ...

  • Dixon 8000D - page 11

    11 SERVICE (continued):  Never run a mower inside a closed area. The exhaust fumes are toxic.  Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition.  Never tamper with safety devices. Check their proper operation regularly.  Keep mower free of grass, leaves, or other debris buildup. Clean up ...

  • Dixon 8000D - page 12

    12 DIXON INDUSTRIES, INC. a BLOUNT company Airport Industrial Park P.O. Box 1569 Coffeyville, Ks 67337- 0945 620-251-2000 Fax 620-251-4117 DIXON LIMITED WARRANTY POLICY - COMMERCIAL MODELS 8000 Series WARRANTY: Home Owner Application: This Dixon Warranty term is for a period of three (3) years from date of purchase. Commercial Application: Dixon mo ...

  • Dixon 8000D - page 13

    13 SPECIFICATIONS 8000 Series (Diesel Version) CHASSIS: 11 GA - rectangular tube, 7 GA reinforcement SEAT: Designed for operator comfort with padded back & arm rests. Seat is adjustable fore & aft. Mounted on operator suspension system with damper. MOWER DECK: 2 decks are available. Both are made of 10 GA fabricated welded construction with ...

  • Dixon 8000D - page 14

    14 CONTROLS CONTROL LEVERS: Note: For access to the seat, move control levers to neutral position and swing them outward. TO GO FORWARD: • From neutral position, gently push both control levers forward. • To increase speed, move levers further forward. TO GO BACKWARD: • From neutral position, gently pull both control levers toward you. TURNIN ...

  • Dixon 8000D - page 15

    15 PARKING BRAKE: A parking brake is located to the left of the seat. The engine will kill if control levers are not in the outboard position when the parking brake is engaged. To engage brake: pull up and back To disengage brake: push forward and down Note: The parking brake is not intended to be used as a service brake. Note: Always set parking b ...

  • Dixon 8000D - page 16

    16 CONTROLS SEAT: Fore & Aft: Move lever, slide seat fore & aft to desired position. Release. Seat Damper: A shock is located on the left side of the seat frame. Remove clip on the top and pull plunger up. Rotate shaft clockwise to make ride stiffer and counter-clockwise for a softer ride. Reattach to seat frame with clip. Attention : Do no ...

  • Dixon 8000D - page 17

    17 CONTROLS MOWER BLADE SWITCH: To engage blades: pull up on switch To disengage blades: push down IGNITION SWITCH:  Turn to run position to energize glow plugs.  Turn to start position when glow plug light turns off, then crank engine. Release when it starts.  For headlights - rotate switch one notch counter-clockwise from run. Note: Remo ...

  • Dixon 8000D - page 18

    18 CONTROLS ...

  • Dixon 8000D - page 19

    19 OPERATION INSTRUCTIONS The safe and successful operation of the 8000 Series Diesel Version will depend upon the operator having the correct knowledge of all controls used on the mower and making good judgements about the terrain to be mowed. NEVER allow anyone to operate the mower without complete knowledge of all controls and their functions. D ...

  • Dixon 8000D - page 20

    20 OPERATION INSTRUCTIONS TESTING OF SAFETY INTERLOCK SYSTEMS: Do not operate mower if safety switches are not operating properly. Your Zero Turning Radius Mower is equipped with control interlocks for your safety. 1. The engine will not start if the mower blades are engaged. 2. The engine will not start unless the steering control levers are neutr ...

  • Dixon 8000D - page 21

    21 INTERLOCK SWITCH TEST: Note: Operator must be seated in normal operating position to perform these tests. 1. With engine off, turn mower blade on and attempt to start engine. ENGINE SHOULD NOT START. 2. With engine off, move control levers in and attempt to start engine. ENGINE SHOULD NOT START 3. In a SAFE AREA, away from bystanders, start the ...

  • Dixon 8000D - page 22

    22 OPERATION INSTRUCTIONS STARTING INSTRUCTIONS: 1. Operator must be seated in normal operating position. 2. Set parking brake. 3. Move control levers to outboard position. 4. Assure blade clutch is off. 5. Push throttle control lever to slow setting. 6. Insert ignition key and turn to run position. Glow plug should light. 7. When glow plug light g ...

  • Dixon 8000D - page 23

    23 OPERATION INSTRUCTIONS MOWING INSTRUCTIONS: Be sure that deflector is properly installed on the discharge chute. 1 . Start engine and set throttle at full speed. 2 . Set desired cut height. 3 . Release park brake. Check the area to assure there is no one near. 4 . Engage mower blades. 5 . Move control levers in and operate per the instructions o ...

  • Dixon 8000D - page 24

    24 OPERATION INSTRUCTIONS GRASS HEIGHT AND CUTTING SUGGESTIONS: Do not attempt to cut grass when it is wet. If the grass is tall, place the mower deck cut height lever in the top or second notch. Initially overlap cutting swaths instead of a full swath with each pass. Some applications may require a second cutting. Keep the underside of the m ...

  • Dixon 8000D - page 25

    25 OPERATION INSTRUCTIONS TO LIFT SEAT: To lift the seat, move the control levers to the neutral OUT position. Unhook the seat damper by rotating the clip of the retaining pin off of the clevis end and remove the retaining pin. Remove the clevis end of the seat damper from the seat hold down bracket and replace the pin and rotating pin clip t ...

  • Dixon 8000D - page 26

    26 OPERATION INSTRUCTIONS TO FREE WHEEL MACHINE (UNLOCK TRANSMISSION): Always turn off engine before engaging or disengaging the hydro release (free wheel) valves. Never attempt to move the valves with the engine running. The hydro release valves are located beneath the seat on the right side of the hydro pump on each side of the machine. To unlock ...

  • Dixon 8000D - page 27

    27 CARE AND MAINTENANCE CAUTION CAUTION CAUTION CAUTION CAUTION Bef Bef Bef Bef Bef ore perf ore perf ore perf ore perf ore perf or or or or or ming an ming an ming an ming an ming an y maintenance y maintenance y maintenance y maintenance y maintenance , tur , tur , tur , tur , tur n off engine n off engine n off engine n off engine n off engine , ...

  • Dixon 8000D - page 28

    28 CARE AND MAINTENANCE ENGINE: For complete maintenance and operating information of the engine, please refer to the maintenance instructions furnished by the engine manufacturer and included in your Zero Turn Radius mower information packet. Note: Air intake screen must be kept clean. If plugged, engine may be seriously damaged by overheating. No ...

  • Dixon 8000D - page 29

    29 MOWER BLADES: Check sharpness of mower blades after every 10 hours of operation. To sharpen blades, proceed as follows. 1. Remove bolt and flat washer mounting blade on shaft. Remove blade. 2. Blades should be discarded when worn excessively. 3. Sharpen blade with a hand file, electric grinder or blade sharpener. Wear gloves and eye protection w ...

  • Dixon 8000D - page 30

    30 CARE AND MAINTENANCE LUBRICATION: 1. Engine: Follow engine manufacturers recommendation. 2. Deck spindles: Lubricate with 3 shots only, every 100 hours. 3. Mower chassis: Lubricate with 3 shots only, every 50 hours (see zerk locations below). ...

  • Dixon 8000D - page 31

    31 CARE AND MAINTENANCE CHECKING & REPLENISHING OIL IN HYDROSTATIC TRANSMISSION: Dirt or water in oil can ruin the hydrostatic transmissions. Check the oil level in hydrostatic transmission oil reservoir after every 25 hours of usage. Clean the oil reservoir cap and the area around it prior to removal. Check the oil level. Oil should be approxi ...

  • Dixon 8000D - page 32

    32 CARE AND MAINTENANCE 1. Loosen the locking screw on the top knob of the brake engaging handle. 2. Rotate it clockwise to increase and counter- clockwise to decrease brake holding power. As the brake holding power is increased, the force required on the handle to engage the brake increases. 3. Set the brake for the holding power required for the ...

  • Dixon 8000D - page 33

    33 HEADLIGHT ADJUSTMENT: 1. Loosen the 1/2 retaining nut underneath the headlight and slide the headlight forward out of the fuel tank. 2. Loosen the 1/2 nut on the U shaped holding bracket and swivel the headlight vertically to adjust the height of the beam. Tighten the bracket nut. 3. Replace headlight in fuel tank. 4. Swivel the head ...

  • Dixon 8000D - page 34

    34 CARE AND MAINTENANCE HYDROSTATIC PUMPS: Before each use, check to be sure that the cooling fins of the hydrostatic pumps are clean. Excessive accumulation of oil, dirt, or trash may cause the pumps to overheat. NEVER WASH ACROSS TOP OF RESERVOIR WITH WATER OR STEAM. Fill reservoir as required per the maintenance schedule listed in this book HYDR ...

  • Dixon 8000D - page 35

    35 CARE AND MAINTENANCE HYDROSTAT DRIVE BELT REPLACEMENT PROCEDURE: To install hydrostat pump drive belt: 1. Rotate the spring loaded take-up idler towards the left hand hydro pump. 2. Install belt per diagram. 3. Install double u-joint and tighten flange bolts (tighten to 14 ft. lbs.). 4. Install radiator and mounting hardware. 5. Attach radiator ...

  • Dixon 8000D - page 36

    36 STEERING CONTROL ADJUSTMENTS: To adjust neutral: 1. Lift seat (see instructions on Page 16). 2. Block up the unit so that the drive wheels are off the ground. 3. Loosen ball joint jam nuts on control rod. Note: The front jam nuts are left hand threads. 4. With steering control arms in the out neutral position, start the engine and run at f ...

  • Dixon 8000D - page 37

    37 STEERING CONTROL ADJUSTMENTS (continued): CARE AND MAINTENANCE To adjust steering control levers: 1. Loosen the front and rear bolts retaining the bellows hold down plate and slide the bellows and plate up the steering lever to expose the steering control mechanism. 2. Move the levers inboard to the operating position. 3. Loosen the set screw of ...

  • Dixon 8000D - page 38

    38 To adjust In position of the steering controls: 1. Move the levers inboard to the operating position. Adjust the steering lever stops until the steering levers have the desired clearance. To adjust for straight forward tracking: 1. Drive tractor with both control levers in the full forward position. 2. Stop the machine and shut off the eng ...

  • Dixon 8000D - page 39

    39 CARE AND MAINTENANCE LEVELING THE DECK: 1. Set the tire pressure on all four tires. 2. Front casters must be rotated in the direction of forward travel. 3. Move the tractor to a hard level surface. 4. Put the mower deck in the number 3 deck height position. 5. Loosen the jam nuts on the front and rear deck hangers. 6. Rotate the 2 outer spindles ...

  • Dixon 8000D - page 40

    40 1 . ENGINE WONT TURN OVER Mower blades engaged- - - - - - - - - - - - - - - - - - - - - - -disengage blades Drive not in neutral - - - - - - -move control levers to neutral OUT Circuit breaker trips - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - reset Dead battery- - - - - - - - - - - - - - - - - - - - - - ...

  • Dixon 8000D - page 41

    41 TROUBLESHOOTING 5. ENGINE OVERHEATED Air intake screen or fins clogged- - - clean intake screen and fins Oil level too low or too high- - - - - - - - - - - - - - - - - - - - - - - - - adjust oil level Running engine too slow- - - - - - - - - - - - - - - - - - - - - - - run engine faster Low coolant level- - - - - - - - - - - - - - - - - - - - - ...

  • Dixon 8000D - page 42

    42 STANDARD SERVICE PARTS LIST MODEL ZTR 8026D: Blades (60): P/N 12421 Blades (72): P/N 12339 Engine to Mower Deck Belt: P/N 12503 Serpentine Belt (60): P/N 9758 Serpentine Belt (72): P/N 12033 Engine to Hydro Belt: P/N 12012 Hydrostatic Transmission Filter: P/N 7252 BRIGGS & STRATTON AIR AND OIL FILTER PART NUMBERS: Refer to engine ...

  • Dixon 8000D - page 43

    43 OWNER INFORMATION Date Purchased _ ________________________________ Mower Model Number ____________________________ Mower Serial Number ____________________________ Purchased From ___ _____________________________ Name ________________________________ Address ________________________________ DATE OIL CHANGED: DATE ENGINE TUNED: _________________ ...

  • Dixon 8000D - page 44

    ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers ZTR®Mowers Dixon® and ZTR® are registered trademarks of Dixon Industries, Inc. DIXON INDUSTRIES, INC. a BLOUNT International Inc. Co. P.O. Box 1569 Coffeyville, Ks 67337-0945 620-251-2000 8000 Series (Diesel) Model 8026D Part No. 13638-xxxx W W W W W ARNING: ARNING: ARNING: ARNING: ARNING: The engi ...

メーカー Dixon カテゴリー Lawn Mower

Dixon 8000Dのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 8000Dの取扱説明書
- Dixonの製品カード
- パンフレット
- またはDixon 8000Dの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Dixon 8000Dの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Dixon 8000Dの取り付け説明書、サービスマニュアル、簡易説明書、またはDixon 8000Dのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Dixon 8000Dの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Dixon 8000Dデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがDixon 8000Dを使用するのを助ける技術的文書のことです。説明書は通常、全てのDixon 8000Dユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Dixonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Dixon 8000Dの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははDixon 8000Dの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Dixon 8000Dに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Dixon 8000Dデバイスの基本機能を使うにあたってのヒント。 Dixon 8000Dのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Dixon 8000Dに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるDixon 8000Dのメーカー/サービスへの連絡先に関する情報。

Dixon 8000Dについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもDixon 8000Dの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDixon 8000Dで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)