-
Honda Automobiles QH4000 - page 1
-I ...
-
Honda Automobiles QH4000 - page 2
...
-
Honda Automobiles QH4000 - page 3
Introduction ..................................................... 1 Safety and Instructional Decals .................................. 2 Assembly 3 Subframe Preparation ........................................... 3 Lift Mechanism ................................................. 3 Tractor Preparation ............................................ 5 ...
-
Honda Automobiles QH4000 - page 4
REPLACE IMMEDIATELY IF DAMAGED . ATTACHING INSTRUCTIONS 1. Insert subframe into attachment completely. 2. Lock in place by movin lever forward to " Lock " 3. e ui ed with P.T.O. drive line, connect to trac - 4: If equipped with lift assist springs, lift theattach- osition and secure wit a linch pin. tor%.% and lock in place. mnt and attac ...
-
Honda Automobiles QH4000 - page 5
- - - -- - - --- IMPORTANT: Before beginning assembly of this subframe, make sure tractor is on a level surface, parking brake is set and that engine is turned off, with key removed. su~ERAME-PREP_ARAILoN a) Loosely attach rear hitch plate (fig.1, item 1) to bottom of subframe channel (fig.1, item 2). Use a 1/2" x 1 1/4" bolt (fig.1, item ...
-
Honda Automobiles QH4000 - page 6
Thread the adjustment fork (fig.2, item 5) into the end of the push arm (fig.2, item 3). Adjust the overall length of push arm assembly to 32 13/16 " . Place an 11/16 " f latwasher and a bent retainer plate (fig.2, item 6) on the 5/8" x 4 " bolt (fig.2, item 7). Insert the bolt into the lever as shown. Place another bent retaine ...
-
Honda Automobiles QH4000 - page 7
a) I 6) C) Loosely attach the front support brackets (fig.5, item 1) to the tractor frame. For each bracket, use one lOmm x 1.25 x 25mm bolt (fig.5, item 2) with lockwasher, and two 10mm x 1.25 x 30mm bolts (fig.5, item. 3) with lockwashers for each bracket. Do not tighten yet. Loosely attach the attaching plates (fig.5 item 4) to the front support ...
-
Honda Automobiles QH4000 - page 8
c) Loosely attach front of subframe flatbars (fig.7, item 1) to the outside attaching plates. Use two 1/2" x 1 1/2" bolts (fig.7, item 31, lockwashers and nuts. Install the bolts from the inside as shown. Do not tighten yet. dl Attach the subframe's rear hitch plate (fig.1, item 1) to the tractor's rear draw plate with the 1/2&q ...
-
Honda Automobiles QH4000 - page 9
Tighten the 1/2" bolts (fig.9, item 1). Refer to the Torque Specification Table on page 11. Secure the rear hitch plate (fig.1, item 1) to the tractor by tightening the then the 1/2" x 1 1/4" bolt (fig. 1, item 3). Refer to the Torque Specification Table on page 11. If necessary, adjust the lift arm (fig.3, item 3) so that the handle ...
-
Honda Automobiles QH4000 - page 10
I I M P O R T A N T I Red ref lectors must be installed on rear fender of tractor when quick hitch is installed. m) Attach the two self adhesive reflectors to the rear fender as illustrated in figure 10. Reflectors should be approximately 1/2" (13mm) up and 6 " (150mm) in from outside corners. To avoid injury, park the tractor on a level ...
-
Honda Automobiles QH4000 - page 11
PARTS GUIDE 1 '2 !3 .4 5 6 7 8 9 10 11 12 13 14 15 16 I 17 ~ 18 1 19 30 Front support bracket RH .. 1 Front support bracket LH -. 1 Attaching plate RH ........ 1 Attaching plate LH ........ 1 Hex bolt 10mm x 25mm ...... 2 Hex bolt 10mm x 30mm ...... 4 Lockwasher 7/16 " . . . . . . . . . - 10 Lockwasher 3/8" ........... 6 Hex bolt 3/8 ...
-
Honda Automobiles QH4000 - page 12
PARTS GUIDE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Hex bolt 3/8" x 2 1/4" .... 2 Hex nut 3/8", Uni - torque . . 2 Lift lever ................ 1 Adjustment fork ........... 1 Push arm .................. 1 Pin (17/32" x 2 1/4") .-. .- 1 Flange bearing ............ 2 Lift arm .................. 2 Tube spacer ............ ...
-
Honda Automobiles QH4000 - page 13
TORQUE SPECIFICATION TABLE GENERAL TORQUE SPECIFICATION TABLE (Revised 2 - 74) USE THE FOLLOWING TORQUES WHEN SPECIAL TORQUES ARE NOT GIVEN NOTE: Thew valuer apply to fasteners as recciwd from supplier. dry, 0, when lutxicatcd with normal enpioe oil. They do not epply if Wcciel praphitcd or moly dirulphide prca~s or other ex- treme pressure lubrica ...
-
Honda Automobiles QH4000 - page 14
Your satisfaction and goodwill are important to your dealer and to us. All Honda warranty details are explained in the Distributor's Limited Warranty. Normally, any problems concerning the product will be handled by your dealer's service department. If you have a warranty problem that has not been handled to your satisfaction, we suggest ...
-
Honda Automobiles QH4000 - page 15
...
-
Honda Automobiles QH4000 - page 16
H/C 3752482 (9307) ...
Honda Automobiles QH4000についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもHonda Automobiles QH4000の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHonda Automobiles QH4000で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。