Makita BLS820の取扱説明書

36ページ 0.35 mb
ダウンロード

ページに移動 of 36

Summary
  • Makita BLS820 - page 1

    INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. Cor dless Compound Miter Sa w Equipped with Electric Blade Brake 216 mm (8-1/2”) MODEL BLS820 001764 ...

  • Makita BLS820 - page 2

    2 SPECIFICATIONS Blade diameter ........................................................................................... 216 mm (8-1/2”) Hole (arbor) diameter ................................................................................. 15.88 mm (5/8”) Max. Miter angle ..................................................................... ...

  • Makita BLS820 - page 3

    3 For Y our Own Safety Read Instruction Manual Bef ore Operating T ool Save it f or future reference GENERAL SAFETY PRECA UTIONS USA005-1 (F or All T OOIS ) 1. KNO W Y OUR PO WER TOOL. Read the owner’ s manual carefully . Learn the tool’ s applications and limitations, as well as the specific potential hazards peculiar to it. 2. KEEP GU ARDS IN ...

  • Makita BLS820 - page 4

    4 18. NEVER ST AND ON T OOL. Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted. 19. CHECK D AMAGED P AR TS. Before further use of the tool, a guard or other part that is damaged should be carefully chec ked to determine that it will operate properl y and perform its intended function - chec k for a ...

  • Makita BLS820 - page 5

    5 14. Make sure that the turn base is properl y secured so it will not move during opera- tion. Use the holes in the base to fasten the saw to a stable w ork platform or bench. NEVER use tool where operator positioning would be a wkward. 15. For your saf ety , remove the c hips, small pieces, etc. from the tab le top before oper- ation. 16. A void ...

  • Makita BLS820 - page 6

    6 IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER & B A TTER Y CARTRIDGE USC002-3 1. SA VE THESE INSTRUCTIONS- This man- ual contains important safety and operat- ing instructions for battery charger . 2. Before using battery char g er , read all instructions and cautionary markings on (1) battery charger , (2) battery , and (3) product using batt ...

  • Makita BLS820 - page 7

    7 ADDITIONAL SAFETY R ULES FOR CHARGER & B A TTER Y CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELO W 10°C (50°F) or ABO VE 40°C (104°F). 2. Do not attempt to use a step-up trans- former , an engine g enerator or DC power receptacle. 3. Do not allow an ything to cover or clog the charger vents. 4. Do not short the batt ...

  • Makita BLS820 - page 8

    8 INST ALLA TION Installing auxiliary plate Installing the auxiliar y plate using the notch in the tool ’ s base and secure it by tightening the he x bolt. Bench mounting When the tool is shipped, the handle is lock ed in the lowered position by the stopper pin. Release the stopper pin b y lower- ing the handle slightly and pulling the stopper pi ...

  • Makita BLS820 - page 9

    9 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge. • T o remove the battery car tr idge , ...

  • Makita BLS820 - page 10

    10 5. If you lea ve the battery car tridge in the charger after the charging cycle is complete, the charger will s witch into its “ trickle charge (maintenance charge) ” mode which will last appro ximately 24 hours. 6. After charging, unplug the charger from the power source. NO TE: • The batter y charger is f or charging Makita batter y car ...

  • Makita BLS820 - page 11

    11 • Check the sound of cooling f an, vent on the charger and batter y , which can be sometime clogged with dust. • The cooling system is in order although no sound of cooling fa n comes out, if the yellow w ar ning light will not flash. • Alwa ys keep clean the v ent on charger and batter y f or cooling. • The products should be sent to re ...

  • Makita BLS820 - page 12

    12 Blade guard When lowering the handle, the b lade guard rises automati- cally . The guard is spring loaded so it retur ns to its original position when the cut is completed and the handle is raised. NEVER DEFEA T OR REMOVE THE BLADE GU ARD OR THE SPRING WHICH A TT A CHES T O THE GUARD . In the interest of your personal saf ety , alwa ys maintain ...

  • Makita BLS820 - page 13

    13 P ositioning kerf board This tool is provided with the k erf boards in the tur n base to minimize tearing on the e xit side of a cut. The kerf boards are f actor y adjusted so that the saw b lade does not contact the kerf boards . Before use , adjust the kerf boards as fo llows: First, remov e the batter y car tridge. Loosen all the scre ws (2 e ...

  • Makita BLS820 - page 14

    14 Adjusting the miter angle Loosen the grip by turning counterclockwise. T ur n the turn base while pressing down the loc k lev er . When you hav e mov ed the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise . CA UTION: • When turning the tur n base, be sure to raise the h ...

  • Makita BLS820 - page 15

    15 • Do not pull the s witch tr igger hard without pressing in the lock-off b utton. This can cause switch breakage . T o prev ent the switch trigger from being accidentally pulled, a lock-off b utton is provided. T o star t the tool, press in the lock- off button and pull the s witch trigger . Release the switch trig- ger to stop . W ARNING: • ...

  • Makita BLS820 - page 16

    16 Socket wrenc h storage The sock et wrench is stored as shown in the figure. When using the sock et wrench, pull it out of the wrench holder . After using the sock et wrench, retur n it to the wrench holder . Installing or removing sa w blade CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef o ...

  • Makita BLS820 - page 17

    17 Press the shaft lock to loc k the spindle and use the socket wrench to loosen the he x bolt clockwise. Then remo ve the he x bolt, outer flange and blade. T o install the blade, mount it carefully onto the spindle , mak- ing sure that the direction of the arrow on the surf ace of the blade matches the direction of the arro w on the blade case. I ...

  • Makita BLS820 - page 18

    18 Dust bag The use of the dust bag makes cutting operations clean and dust collection easy . T o attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remov e the dust bag from the tool and pull the f astener out. Empty the dust bag of its contents, tapping it lightly so as to remo ve par ticles adher- ing to the ...

  • Makita BLS820 - page 19

    19 V ertical vise The vertical vise can be installed in two positions on either the left or right side of the guide fence or the holder assemb ly (optional accessor y). Insert the vise rod into the hole in the guide f ence or the holder assembly and tighten the screw to secure the vise rod. P osition the vise arm according to the thickness and shap ...

  • Makita BLS820 - page 20

    20 CA UTION: • Grip the workpiece only when the projection is at the topmost position. F ailure to do so may result in insufficient securing of the workpiece. This could cause the workpiece to be thrown, cause damage to the b lade or cause the loss of control, which can result in PERSONAL INJUR Y . Holders and holder assembl y (optional accessori ...

  • Makita BLS820 - page 21

    21 • Gently press down the handle to perf or m the cut. If the handle is pressed down with f orce or if lateral fo rce is applied, the blade will vibr ate and leave a mark (saw mark) in the workpiece and the precision of the cut will be impaired. 1. Press cutting Secure the workpiece with the vise. Switch on the tool without the blade making an y ...

  • Makita BLS820 - page 22

    22 • When pressing the handle down, apply pressure parallel to the blade . If the pressure is not parallel to the blade during a cut, the angle of the blade might be shifted and the precision of the cut will be impaired. 4. Compound cutting Compound cutting is the process in which a be vel angle is made at the same time in which a miter angle is ...

  • Makita BLS820 - page 23

    23 There are crown and co ve molding joints which are made to fit “ Inside ” 90 ° corners ((1) and (2) in Fig. A) and “ Outside ” 90 ° corners ((3) and (4) in Fig. A). Measuring Measure the wall length and adjust workpiece on tab le to cut wall contact edge to desired length. Alw ays make sure that cut workpiece length at the bac k of the ...

  • Makita BLS820 - page 24

    24 Example: In the case of cutting 52/38 ° type crown molding f or position (1) in Fig. A: • Tilt and secure be vel angle setting to 33.9 ° LEFT . • Adjust and secure miter angle setting to 31.6 ° RIGHT . • La y crown molding with its broad back (hidden) surf ace down on the tur n base with its CEILING CONT ACT EDGE against the guide f enc ...

  • Makita BLS820 - page 25

    25 EN0002-1 Compound Miter Saw Miter and Bevel Angle Settings 000031 52 ˚ 38 ˚ Ceiling W all W all to Crown Molding Angle: 52/38 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) 60 43.0 46.8 101 30.1 26.9 141 15.3 12. ...

  • Makita BLS820 - page 26

    26 EN0003-1 Compound Miter Saw Miter and Bevel Angle Settings 000032 45 ˚ 45 ˚ Ceiling W all W all to Crown Molding Angle: 45 degrees W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel An gle (deg.) Miter Angle (deg.) W all Angle (deg.) Bevel Angle (deg.) Miter Angle (deg.) 60 37.8 50.8 101 26.7 30.2 141 13.7 14.1 6 ...

  • Makita BLS820 - page 27

    27 6. Cutting repetitive lengths When cutting se veral pieces of stoc k to the same length, ranging from 220 mm (8-5/8 ” ) to 365 mm (14-3/8 ” ), use of the set plate (optional accessor y) will f acilitate more efficient operation. Install the set plate on the holder (optional accessor y) as sho wn in the figure. Align the cutting line on your ...

  • Makita BLS820 - page 28

    28 W ARNING: • Alwa ys be sure that the blade is sharp and clean for the best and saf est performance. Adjusting the cutting angle This tool is carefully adjusted and aligned at the fa ctor y , but rough handling ma y have aff ected the alignment. If your tool is not aligned properly , perform the follo wing: 1. Miter angle Loosen the grip which ...

  • Makita BLS820 - page 29

    29 2. Bevel angle (1) 0 ° be vel angle Lower the handle fully and loc k it in the lowered position by pushing in the stopper pin. Loosen the le ver at the rear of the tool. Tu r n t h e 0 ° bev el angle adjusting bolt (lower bolt) on the right side of the ar m two or three re volutions counterclockwise to tilt the b lade to the ri ght. Carefully ...

  • Makita BLS820 - page 30

    30 Replacing carbon brushes Remov e and check the carbon brushes regularly . Replace when they we ar down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. Use a screwdriv er to remove the brush holder caps. T ake out the wo ...

  • Makita BLS820 - page 31

    31 AC C E S S O R I E S CA UTION: • These accessories or attachments are recommended for use with your Makita tool specified in this man ual. The use of any other accessories or attachments might present a risk of injur y to persons. Only use accessory or attachment f or its stated pur pose. If you need an y assistance for more details regarding ...

  • Makita BLS820 - page 32

    Memo 32 ...

  • Makita BLS820 - page 33

    33 Fold Cut Stamp Timbre Makita Canada Inc. 1950 Forbes Street, Whitb y , Ontario L1N 7B7 ...

  • Makita BLS820 - page 34

    34 Y our answer s to the following questions are appreciated. Date Purchased Model No . Serial No. Initial Last Name Street Address City Province AGE: Male Female Married Single Month Day Y ear 20 Under 19 20-29 30-39 40-49 Over 50 P aste Paste P aste Paste P aste P aste Paste P aste P aste Paste P aste Paste P aste P aste P aste Paste P aste Paste ...

  • Makita BLS820 - page 35

    35 F actory Ser vice Centres For the authorized service centre nearest you please refer to the local yellow pages directory under “ tools ” or con- tact our customer service department (Tel) 1-800-263-3734 When you need service... • Explain the problem in a letter • Enclose the letter with the tool • Package carefully and send prepaid to ...

  • Makita BLS820 - page 36

    Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita ’ s ...

メーカー Makita カテゴリー Cordless Saw

Makita BLS820のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- BLS820の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita BLS820の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita BLS820の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita BLS820の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita BLS820のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita BLS820の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita BLS820デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita BLS820を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita BLS820ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita BLS820の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita BLS820の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita BLS820に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita BLS820デバイスの基本機能を使うにあたってのヒント。 Makita BLS820のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita BLS820に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita BLS820のメーカー/サービスへの連絡先に関する情報。

Makita BLS820についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita BLS820の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita BLS820で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)