HERO 1240の取扱説明書

24ページ 0.19 mb
ダウンロード

ページに移動 of 24

Summary
  • HERO 1240 - page 1

    PROFESSIONAL CONTRACTOR PRODUCTS 2719 Lake City Way, Burnaby, BC, V5A 2Z6 ? P.O. Box 75, Custer WA 98240 - 0052 ? Phone: (604) 420 - 6543 Fax: (604) 420 - 8725 OPERATOR’S MANUAL Model 1240 Model 1260 Model 2260 ...

  • HERO 1240 - page 2

    HERO Operator’s Manual – Page 1 of 23 Thank you for choosing HERO HVLP (High - Volume Low - Pressure) sprayers for your spraying needs. At HERO Industries, we take pride in our precision - engineered products and want you to obtain all the benefits that your HERO sprayer has to offer. To ensure th e proper use and maintenance of your HERO spray ...

  • HERO 1240 - page 3

    HERO Operator’s Manual – Page 2 of 23 CONTENTS Page 1. THE HERO HVLP ADVANTAGE 3 2. GETTING STARTED 2.1 Unpacking Your HERO System 4 2.2 Testing The Tu rbine 4 2.3 Testing The Variable Speed Control 4 2.4 Connecting The Hose To The Turbine 5 2.5 Connecting The Spray Gun And Test Spray 5 3. GENERAL OPERATING INSTRUCTIONS 3.1 Operati ng Instructi ...

  • HERO 1240 - page 4

    HERO Operator’s Manual – Page 3 of 23 THE HERO HVLP ADVANTAGE HERO Turbine - Powered HVLP Sprayers are powered by an electric turbine which supplies a consistent flow of high volume, low pressure air (4 - 6 PSI @ 95 - 130 CFM) to the spray gun to atomize the paint or coating (dye, lacquer, adhesive, etc.) bei ng applied. By spraying at low pres ...

  • HERO 1240 - page 5

    HERO Operator’s Manual – Page 4 of 23 GETTING STARTED 2.1 UNPACKING YOUR HERO SYSTEM Unpack your new HERO system from the box. Ensure that all items are included with your system: Cup - Fed Systems include: turbine, air hose and spray gun Volume - Fed Systems With Built - In Compressors include: turbine, Lower Deck Fluid Delivery System (includ ...

  • HERO 1240 - page 6

    HERO Operator’s Manual – Page 5 of 23 2.4 CONNECTING THE HOSE TO THE TURBINE With the power switch in the OFF position, uncoil the air hose and screw it hand - tight to the turbine air outlet. Although the hose is designed for industrial use, it is not crushproof. Do not stand on the hose for extended periods. For information on wire - bound cr ...

  • HERO 1240 - page 7

    HERO Operator’s Manual – Page 6 of 23 GENERAL OPERATING INSTRUCTIONS 3.1 OPERATING INSTRUCTIONS AND PAINTING TIPS For the specific Oper ating Instructions and Painting Tips of your HERO sprayer, please refer to the laminated card attached to the turbine handle of your system. If this card is missing or has been lost, please contact your local H ...

  • HERO 1240 - page 8

    HERO Operator’s Manual – Page 7 of 23 Viscosity Chart Prop erties and thickness of coatings vary from one manufacturer to another. The following chart is a guideline only . Use these times as a guideline in determining the appropriate viscosity based on your spraying technique and finish standards. Some high sol ids coatings may exceed a reason ...

  • HERO 1240 - page 9

    HERO Operator’s Manual – Page 8 of 23 The size of the Air Cap is determined by the size of the center hole. Every Air Cap is stamped with number 1, 2, or 3 to indicate the range in size. The larger the center hole (No. 3), the greater the amount of atomizing air around the Fluid Tip. To ensure proper performance, ensure that the Air Cap hole is ...

  • HERO 1240 - page 10

    HERO Operator’s Manual – Page 9 of 23 3.4 SURFACE PREPARATION Ensure that the surface you are spraying is clean, dry, and free from dust, oil, grease or any ot her contaminant. A dirty or greasy surface will affect adhesion, can spoil a finish and is very difficult to correct once sprayed. If possible, always clean the surface with a tack rag t ...

  • HERO 1240 - page 11

    HERO Operator’s Manual – Page 10 of 23 3.7 OPERATIN G THE SPRAY GUN Fill the cup as necessary (up to the shoulder maximum) with the properly diluted paint or coating. Do not overfill the cup as this may cause leakage or may block the air pressure holes and prevent pressurization of the cup. Spray Patt ern Selection To select the desired spray p ...

  • HERO 1240 - page 12

    HERO Operator’s Manual – Page 11 of 23 The direction of the spraying motion should be based on the spray pattern chosen: when spraying a horizontal pattern, the direction should be up and down; when spraying a vertical pattern, the direction should be left to right or right to left; when spraying a round pattern, the direction can be either. CA ...

  • HERO 1240 - page 13

    HERO Operator’s Manual – Page 12 of 23 Even Drip Figure 8 Running/Dripping From Extremities Running/Dripping From Center 3.9 BASIC SPRAYING TECHNIQUES ?? For applications where thicker coa ts are required and finish quality is critical, consider applying two thinner coats. The reduction in paint consumption and drying time when spraying with HE ...

  • HERO 1240 - page 14

    HERO Operator’s Manual – Page 13 of 23 Correct Application Technique Incorrect Application Technique Overlap strokes up to 50% to ensure proper coverage and avoid streaks: When spraying an edge or corner, split the center of the spray pattern on the corner or edge so that each side receives 50% of the spray pattern and equal amounts of paint: ...

  • HERO 1240 - page 15

    HERO Operator’s Manual – Page 14 of 23 CLEANING AND MAINTENANCE 4.1 BASIC CLEAN UP If you are taking a break or plan to spray the same material again within a reasonable time: 1. Turn off the turbine and disconnect the gun from the hose. 2. Turn the Material Flow Adjustment Screw at the back of the gun clockwise until it stops and clean any exc ...

  • HERO 1240 - page 16

    HERO Operator’s Manual – Page 15 of 23 4.3 COMPLETE DISASSEMBLY AND CLEANING OF SPRAY GUN Per iodically, especially after spraying an adhesive, a catalyzed coating, or any other material that is known to be difficult to clean, HERO recommends that you completely disassemble your gun and clean each part individually. If necessary, contact your l ...

  • HERO 1240 - page 17

    HERO Operator’s Manual – Page 16 of 23 en large the holes of these critical parts and affect the performance of your system when used. When re - assembling the gun, it is recommended to apply a little white grease or petroleum jelly on all threaded and tight tolerance parts: Material Flow Adjustme nt Screw and Spring; Air Distributor; Sleeve Nu ...

  • HERO 1240 - page 18

    HERO Operator’s Manual – Page 17 of 23 The Gland Seal is located behind the Gland Nut directly in front of the gun trigger and should be replaced periodically as part of preventive maintenance. A worn Gland Seal can be the cause of leaking between the Gland Nut and the Needle directly in front of the trigger. If leaking occurs, try tightening t ...

  • HERO 1240 - page 19

    HERO Operator’s Manual – Page 18 of 23 TROUBLE SHOOTING 5.1 BASIC T ROUBLESHOOTING CHART Problem Probable Cause Solution(s) Turbine not working at all A. No power to the turbine B. Re - settable breaker has been activated A. Check power outlet/socket B. Re - set breaker on face of turbine by pressing it once Low Air Flow A. Filters are blocked ...

  • HERO 1240 - page 20

    HERO Operator’s Manual – Page 19 of 23 5.1 BASIC TROUBLESHOOTING CHA RT (Continued) Problem Probable Cause Solution(s) Not Spraying At All or Inconsistent Material Flow (spitting) With A Cup Gun A. Air Cap too far from Fluid Tip B. Dry paint on end of Fluid Tip C. Coating is too thick: not enough pressure to pump from cup to Flu id Tip D. Forei ...

  • HERO 1240 - page 21

    HERO Operator’s Manual – Page 20 of 23 5.2 TROUBLESHOOTING FINISH PROBLEMS Problem Probable Cause Solution(s) Runs or Sags A. Coating has been over - diluted B. Application speed too slow C. Improper overlapping D. Needle and Fluid Tip too large E. Film thickness is too thick for one coat F. Gun too close t o surface G. Insufficient atomizing a ...

  • HERO 1240 - page 22

    HERO Operator’s Manual – Page 21 of 23 OPTIONS AND ACCESSORIES 6.1 CUP - FED SYS TEMS Cup - Fed Systems include a turbine, air hose and cup - fed spray gun. The guns with these systems are supplied with a 1 Qt/L paint cup and are ideal for spraying applications where versatility and portability are essential. 6.2 VOLUME - FED SYSTEMS WITH BUILT ...

  • HERO 1240 - page 23

    HERO Operator’s Manual – Page 22 of 23 6.5 GUN EXTENSION WANDS, TOUCH - UP CUP KIT AND OTHER ACCESSORIES Gun Extension Wands For ease of use when spraying in hard to rea ch areas, ceilings, floors, decks, etc., Gun Extension Wands can be installed on any HERO gun with a spring loaded air cap. Wands are available in 12”, 18”, and 24” lengt ...

  • HERO 1240 - page 24

    HERO Operator’s Manual – Page 23 of 23 WARRANTY INFORMATION LIMITED WARRANTY HERO Industries warrants to the original purchaser that the HERO equipment described in this manual will be free of defects in materials and workmanship for a period of ONE (1) YEAR from the date of purchase. HERO Industries’ only obligation shall be to repair or rep ...

メーカー HERO カテゴリー Paint Sprayer

HERO 1240のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 1240の取扱説明書
- HEROの製品カード
- パンフレット
- またはHERO 1240の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、HERO 1240の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、HERO 1240の取り付け説明書、サービスマニュアル、簡易説明書、またはHERO 1240のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、HERO 1240の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

HERO 1240デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHERO 1240を使用するのを助ける技術的文書のことです。説明書は通常、全てのHERO 1240ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

HEROの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. HERO 1240の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHERO 1240の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。HERO 1240に関してこのドキュメントで見つけることができる全てのヒントの目次
3. HERO 1240デバイスの基本機能を使うにあたってのヒント。 HERO 1240のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。HERO 1240に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHERO 1240のメーカー/サービスへの連絡先に関する情報。

HERO 1240についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHERO 1240の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHERO 1240で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)