Snapper 7800388の取扱説明書

16ページ 1.53 mb
ダウンロード

ページに移動 of 16

Summary
  • Snapper 7800388 - page 1

    8/2008 1 TP 300-5412---ZT-SN Axion / 150Z Series Form No. 7102754 Briggs & Stratton Yard Power Products Group Copyright © 2008 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved This Dealer Setup Instruction covers the following products: Initial setup Model. No. Description 7800360 Simplicity Axion Model ZT18533, 18.5HP ...

  • Snapper 7800388 - page 2

    Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 2 T ABLE OF CONTENTS: SAFETY RULES .................................................................3 SETUP PROCEDURES Quick Setup List ................................................................6 Uncrating ............................................................................7 Battery Activ ...

  • Snapper 7800388 - page 3

    Axion / 150Z Series 8/2008 3 TP 300-5412---ZT-SN SAFETY R ULES GENERAL OPERA TION 1. Read, understand, and follow all instructions in the manual and on the unit before starting. 2. Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. 3. Only allow responsible adults, who are familiar w ...

  • Snapper 7800388 - page 4

    Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 4 CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and the mowing activity. Never assume that children will remain where you last saw them. 1. Keep children out of the mowing area and under the watchful care of anothe ...

  • Snapper 7800388 - page 5

    Axion / 150Z Series 8/2008 5 TP 300-5412---ZT-SN SER VICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other sources of ignition. 2. Use only approved gasoline containers. 3. Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling. 4. Never fuel the machin ...

  • Snapper 7800388 - page 6

    Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 6 Quick Setup List P age Setup Procedure Steps to P erform 7 Uncrating ❏ Remov e crate & banding. ❏ Place transmissions in R OLL RELEASE position & roll off skid. 8 Battery Activation & ❏ Charge the battery (Note: proceed with other setup steps Installation while batter y is charging) ...

  • Snapper 7800388 - page 7

    8/2008 7 TP 300-5412---ZT-SN Axion / 150Z Series Uncrating 1. Using a reciprocating utility saw or equivalent, cut crate away from bottom skid. Remove crate. Remove plastic wrap. 2. Cut any banding securing the unit. IMPORT ANT NO TE When cutting crate from bottom skid, use caution around tires and mower rollers. 3. Locate the transmission release ...

  • Snapper 7800388 - page 8

    TP 300-5412---ZT-SN 8/2008 8 Axion / 150Z Series W ARNING Corrosion hazard. Batteries contain acid. Always keep the battery upright and do not spill the electrolyte. Avoid contact with skin and eyes. Explosion hazard. Changing the battery produces explosive hydrogen gas. Only charge the battery in a well ventilated area, away from any ignition sour ...

  • Snapper 7800388 - page 9

    8/2008 9 TP 300-5412---ZT-SN Axion / 150Z Series 5/16-1 8 x 3/4 14-19 ft. lbs. 19-25 N.m. Installing the Seat 1. Raise the seat base. 2. Align the holes in the seat bottom with the holes in the seat base. 3. Secure the seat to the seat base with four 5/16-18 x 3/4” bolts. Torque to 14-19 ft. lbs. (19-25 N.m.) See Figure 5. Figure 5. Installing th ...

  • Snapper 7800388 - page 10

    Axion / 150Z Series TP 300-5412---ZT-SN 8/2008 10 Installing the Seat Safety Switc h 1. Squeeze the side clips of the safety switch (A, Figure 6), and insert the switch into the slot (B) in the seat bottom. Be sure to slide the switch fully forward. 2. Connect the harness terminal housing (C) to the seat switch. 3. Loop the wire tie (D) around both ...

  • Snapper 7800388 - page 11

    Axion / 150Z Series 8/2008 11 TP 300-5412---ZT-SN 5/16-1 8 x 1-3/4 5/16-1 8 15-17 ft. lbs. 20-23 N.m. Setting Up the Gr ound Speed Contr ol Le vers 1. Loosen (do not remove) the hardware securing the ground speed control levers to the lever bases. 2. Raise the levers, aligning the upper hole in each lever with the upper slotted hole in the lever ba ...

  • Snapper 7800388 - page 12

    TP 300-5412---ZT-SN 8/2008 12 Axion / 150Z Series 30-40 ft. lbs. 41-54 N.m. T or que Mower Blade Har d ware 1. Check to see that the blade and hardware are installed according to the diagram shown (A, Figures 8-10). 2. Torque the blade hardware to the noted torque (B): Note: Use a wooden block to prevent blade rotation. A B Figure 8. Torquing the m ...

  • Snapper 7800388 - page 13

    8/2008 13 TP 300-5412---ZT-SN Axion / 150Z Series 8 0-90 ft. lbs. 10 8 -122 N.m. A B Figure 9. Torquing the mower blade hardware (42” Deck) 45-55 ft. lbs. 61-75 N.m. A B Figure 10. Torquing the mower blade hardware (50” Deck) ...

  • Snapper 7800388 - page 14

    TP 300-5412---ZT-SN 8/2008 14 Axion / 150Z Series Size PSI bar Rear 10-12 ,69-, 8 3 Fr o n t 1 8 -20 1,24-1,3 8 Chec k Fluid Le vels Fill & Chec k Engine Oil Removing the rear cover to gain access to the engine, use the dipstick (Figure 11) to check the engine oil level. If necessary add engine oil. Check engine manufacturer’s owner’s manua ...

  • Snapper 7800388 - page 15

    8/2008 15 TP 300-5412---ZT-SN Axion / 150Z Series 42” Deck shown, all decks similar Figure 13. Lubrication (deck) Figure 14. Lubrication (ground speed control levers) Figure 15. Lubrication (chassis and wheels) Lubrication Lubricate the unit at the following lubrication points as well as those shown in Figures 13-15. Grease: • front caster whee ...

  • Snapper 7800388 - page 16

    TP 300-5412---ZT-SN 8/2008 16 Axion / 150Z Series CHECK RIDER SAFETY SYSTEM Service Interval: Every 100 hours, every spring/fall, and after storage of 30 days or longer. This unit is equipped with safety interlock switches. These safety systems are present for your safety. Do not attempt to bypass safety switches, and never tamper with safety devic ...

メーカー Snapper カテゴリー Lawn Mower

Snapper 7800388のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 7800388の取扱説明書
- Snapperの製品カード
- パンフレット
- またはSnapper 7800388の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Snapper 7800388の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Snapper 7800388の取り付け説明書、サービスマニュアル、簡易説明書、またはSnapper 7800388のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Snapper 7800388の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Snapper 7800388デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSnapper 7800388を使用するのを助ける技術的文書のことです。説明書は通常、全てのSnapper 7800388ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Snapperの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Snapper 7800388の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSnapper 7800388の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Snapper 7800388に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Snapper 7800388デバイスの基本機能を使うにあたってのヒント。 Snapper 7800388のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Snapper 7800388に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSnapper 7800388のメーカー/サービスへの連絡先に関する情報。

Snapper 7800388についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSnapper 7800388の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper 7800388で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)