AudioSource AMP200の取扱説明書

6ページ 0.39 mb
ダウンロード

ページに移動 of 6

Summary
  • AudioSource AMP200 - page 1

    Phoenix Gold International, Inc. 9300 North Decatur Street Portland, Oregon 97203 T el: 503.286.9300 F ax: 503.978.3381 T ech Support: 800.950.1449 W eb: www .phoenixgold.com Email: support@phoenixgold.com OWNER’S MANUAL 8100.0303 A ...

  • AudioSource AMP200 - page 2

    W ARNING CA UTION RISK OF ELECTRIC SHOCK DO NO T OPEN T O PREVENT FIRE OR SHOCK HAZARD , DO NO T USE THIS PL UG WITH AN EX TENSION C ORD , RECEPT ACLE OR O THER OUTLET UNLESS THE BLADES CAN BE FULL Y INSERTED TO PREVENT BLADE EXPOSURE. T O PREVENT FIRE OR SHOCK HAZARD , DO NO T EXPOSE THIS APPLIANCE T O RAIN OR MOISTURE. T O PREVENT ELECTRICAL SHOC ...

  • AudioSource AMP200 - page 3

    Y ou should use a 3.5mm phone plug in the “IN” connector to make this connection. The tip of the connector is (+) positive , and the sleeve of the connector is (-) negative . A second terminal in the same block is labeled “OUT ” . This allows for remote turn-on of other devices when the AMP300 is po wered on. Use the same polarity for the t ...

  • AudioSource AMP200 - page 4

    Master Lev el Controls Each channel is able to control its v olume independently relative to the other channel. At the bottom left of the rear panel, there are 2 screwdriver adjustment knobs which correspond to the v olume level of the channel identified by a channel designator below it. The volume range is labeled Minimum to Maximum and has 1 step ...

  • AudioSource AMP200 - page 5

    NO TE : Only one pair of channels can be bridged together . Do not attempt to bridge both A & B speaker terminals, as this may result in a low er impedance than the amplifier is designed to accommodate , and may damage your amplifier . The minimum impedance for the total load connected to a pair of channels in the bridged mode is 8-ohm. NO TE : ...

  • AudioSource AMP200 - page 6

    6 Stereo Setup In this configuration, the mono switch is set to stereo f or stereo operation. Connect the line out jacks from a stereo preamplifier or source to the Line 2 input jacks of y our AMP200. Nex t connect your speakers to the terminals marked “SPEAKER A ” observing proper polarit y (see “Speaker T ermi- nals” Page 5). Connect a se ...

メーカー AudioSource カテゴリー Stereo Amplifier

AudioSource AMP200のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- AMP200の取扱説明書
- AudioSourceの製品カード
- パンフレット
- またはAudioSource AMP200の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、AudioSource AMP200の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、AudioSource AMP200の取り付け説明書、サービスマニュアル、簡易説明書、またはAudioSource AMP200のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、AudioSource AMP200の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

AudioSource AMP200デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAudioSource AMP200を使用するのを助ける技術的文書のことです。説明書は通常、全てのAudioSource AMP200ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

AudioSourceの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. AudioSource AMP200の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAudioSource AMP200の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。AudioSource AMP200に関してこのドキュメントで見つけることができる全てのヒントの目次
3. AudioSource AMP200デバイスの基本機能を使うにあたってのヒント。 AudioSource AMP200のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。AudioSource AMP200に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAudioSource AMP200のメーカー/サービスへの連絡先に関する情報。

AudioSource AMP200についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAudioSource AMP200の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudioSource AMP200で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)