日本語 dropdown-ico

AMX Wall Docking Station MVP-WDSの取扱説明書

38ページ 1.16 mb
ダウンロード

ページに移動 of 38

Summary
  • AMX Wall Docking Station MVP-WDS - page 1

    Installation Guide Touch Panels & Accessories MVP-WDS Wall Docking Station for MVP-7500/8400 Modero ® ViewPoint ® Wireless Touch Panels Last Revised: 12/15/200 8 ...

  • AMX Wall Docking Station MVP-WDS - page 2

    AMX Limited Warranty and Disclaimer AMX warrants its products to be free of defects in material and workmanship under n ormal use for three (3) years from the date of purchase fr om AMX, with the following exceptions: • Electroluminescent and LCD Control P ane ls are warranted for three (3) years, except for the display and touch overlay componen ...

  • AMX Wall Docking Station MVP-WDS - page 3

    FCC Information This device complies with Part 15 of the FCC Rules. Operati on is subject to the followi ng two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference rece ived; in cluding inte rference that may cause undesi red operation. Federal Communications Commission (FCC) Statement Th ...

  • AMX Wall Docking Station MVP-WDS - page 4

    ...

  • AMX Wall Docking Station MVP-WDS - page 5

    Table of Contents i MVP-WDS Wall Docking Station for MVP Panels Table of Contents MVP-WDS Wall Docking Station & CB-MVPWDS Rou gh-In Box ......................... 1 Overview .............................. ......................... ................... ......................... ............... 1 Specification s ............ ................ ..... ...

  • AMX Wall Docking Station MVP-WDS - page 6

    ii MVP-WDS Wall Docking Station for MVP Panels Table of Contents ...

  • AMX Wall Docking Station MVP-WDS - page 7

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 1 MVP-WDS Wall Docking Station for MVP Panels MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box Overview The MVP-WDS W all/Flush Mount Docking Station (FIG. 1) pro vides a surface-installed docking location. MVP-WDS stations use a security latch to secure the panel to the docking sta ...

  • AMX Wall Docking Station MVP-WDS - page 8

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 2 MVP-WDS Wall Docking Station for MVP Panels Specifica tions MVP-WDS Specifications Dimensions (HWD): • 8.59" x 12.66" x 3.40" (21.82 cm x 32.16 cm x 8.64 cm) Note : Always use the cutout/installat ion dimensions for the MVP-WDS when installing this unit into various surfac ...

  • AMX Wall Docking Station MVP-WDS - page 9

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 3 MVP-WDS Wall Docking Station for MVP Panels MVP-WDS docking station co nnector locations FIG. 2 shows the layout of the connectors on the right side of the MVP-WDS. LED Indicators The two LEDs located within the security release pushbutton on the front panel (FIG. 1) indicate battery and c ...

  • AMX Wall Docking Station MVP-WDS - page 10

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 4 MVP-WDS Wall Docking Station for MVP Panels Installation MVP-WDS wall-docking stations can be installed either the CB-MVPWDS or othe r solid surface en vironment using one of the two mounting o ptions: drywall clips or solid surface s cr ews, as described in the following sub-sections. Ins ...

  • AMX Wall Docking Station MVP-WDS - page 11

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 5 MVP-WDS Wall Docking Station for MVP Panels 2. Using either nails or screws, fasten the rough-in box to the stud through the fiv e Stud Fastening Holes. 3. Remove the wiring knockouts from the right side of the rough-in box to accommodate cabling to the MVP-WDS. 4. Thread the USB and Power ...

  • AMX Wall Docking Station MVP-WDS - page 12

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 6 MVP-WDS Wall Docking Station for MVP Panels 4. Close the battery cov er and disconnect the power connector to remo ve po wer from the unit and maintain the support cradle in the forward position. 5. Remov e the two #6-32 F aceplate Security Screws from the top rim of the faceplate, using a ...

  • AMX Wall Docking Station MVP-WDS - page 13

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 7 MVP-WDS Wall Docking Station for MVP Panels 8. Press down on the Security Latch to allow it to go through the top op ening. 9. Grasp the top rim of the faceplate and carefully slide it over the cradle (at an angle) until the faceplate is completely removed from the WDS (FIG. 8). Once the f ...

  • AMX Wall Docking Station MVP-WDS - page 14

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 8 MVP-WDS Wall Docking Station for MVP Panels Installing the MVP-WDS in a CB- MVPWDS Rough-In Box  The rough-in box must be mounted prior to continuing this section. Refer to the Installing the CB-MVPWDS Rough-In Box section on page 4 for de tailed pre-wall installation instructions.  ...

  • AMX Wall Docking Station MVP-WDS - page 15

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 9 MVP-WDS Wall Docking Station for MVP Panels 3. Using a grounded Phillips-head screwdriv er , insert and secure four #6-32 Mounting Screws (not included) into their corresponding holes loca ted along the sides of the MVP-WDS until the W DS is securely fastened to the rough-in box, and is fl ...

  • AMX Wall Docking Station MVP-WDS - page 16

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 10 MVP-WDS Wall Docking Station for MVP Panels 2. Thread the USB and Power cables through the surface opening, leaving enough slack in the wiring to accommodate re-positioning of the unit. 3. Connect the 2-pin power connector and USB cables to the WDS. The WDS must be installed with these at ...

  • AMX Wall Docking Station MVP-WDS - page 17

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 11 MVP-WDS Wall Docking Station for MVP Panels 6. T ighten all four drywall clip sets (scre ws and clips) until both Mounting T abs are securely fastened and flush against the wall. 7. Follo w the steps outlined in the Replacing the F aceplate on the MVP-WDS section on page 13 to angle the M ...

  • AMX Wall Docking Station MVP-WDS - page 18

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 12 MVP-WDS Wall Docking Station for MVP Panels 2. Thread the USB and Power cables through the surface opening, leaving enough slack in the wiring to accommodate any re-positioning of the unit. 3. Connect the 2-pin power connector and USB cables alo ng the right side of the (un-powered) MVP-W ...

  • AMX Wall Docking Station MVP-WDS - page 19

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 13 MVP-WDS Wall Docking Station for MVP Panels 7. Insert and secure four #4-40 Mounting Screws ( not included) into their corresponding holes located along the sides of the WDS (using a grounded Phillips-head screwdri ver) until the WDS is secured and is flush against the wall. 8. Follo w th ...

  • AMX Wall Docking Station MVP-WDS - page 20

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 14 MVP-WDS Wall Docking Station for MVP Panels 7. Apply power to the MVP-WDS by connecting the terminal end of the power cable to the po wer supply . 8. Press the Cradle Acti vation pushb utton to cause the MVP Support Cradle to angle backwards and lie flush against the main unit. 9. Remov e ...

  • AMX Wall Docking Station MVP-WDS - page 21

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 15 MVP-WDS Wall Docking Station for MVP Panels Connecting and Usi ng USB In put Devices on the Stations The MVP-WDS can have up to two USB input de vices connected for use on the MVP panel’ s different firmw are and TPD4 panel page s. These input devices can consist of a ke yboard and mous ...

  • AMX Wall Docking Station MVP-WDS - page 22

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 16 MVP-WDS Wall Docking Station for MVP Panels Securing an MVP Panel to an MVP-WDS 1. Place the MVP-WDS on a flat and lev el surface. 2. Provide po wer to the MV P-WDS (refer to the P owering the MVP-WDS section on page 14). 3. Place the MVP on the support cradle so that the alignment pins o ...

  • AMX Wall Docking Station MVP-WDS - page 23

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 17 MVP-WDS Wall Docking Station for MVP Panels Removing an MVP Panel from an MVP-WDS The MVP security feature enables a security code that is entered into an on-screen password keypad. This password is conf igured within the MVP panel’ s P assword Setup page. Refer to the MVP-7500/8400 Ope ...

  • AMX Wall Docking Station MVP-WDS - page 24

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 18 MVP-WDS Wall Docking Station for MVP Panels Undock-<USER> Stri ng When the MVP is removed from the docking station (undocked), the undock-<user> string is sent to the NetLinx Master .  If the panel has no info rmation within the User A ccess Passwords list, ’ none ’ is ...

  • AMX Wall Docking Station MVP-WDS - page 25

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 19 MVP-WDS Wall Docking Station for MVP Panels Installing the MVP-WDS-SK Silver Conversion Kit The VP-WDS-SK Silver Con version Kit (FG5965-22) contains the following components:  One Silver Cradle Bezel/Faceplate (60-5965-20SL)  One Silver Cradle Pi vot ( Support Cr adle ) (60-5965-21 ...

  • AMX Wall Docking Station MVP-WDS - page 26

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 20 MVP-WDS Wall Docking Station for MVP Panels 7. Disconnect the 2-pin mini-Phoenix connec tor from the side of the docking station to re mov e power from the unit and maintain the support cradle in this angled position. 8. Close the battery cov er . 9. Remov e the two #6-32 Faceplate Securi ...

  • AMX Wall Docking Station MVP-WDS - page 27

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 21 MVP-WDS Wall Docking Station for MVP Panels 14. Press downward on the Security Latch (tow ards the pushbutton) to get it to go through the top opening and allow the faceplate’ s remov al. 15. Grab the top rim of the faceplate and carefully slid e it o ver the cradle (at an angle) until ...

  • AMX Wall Docking Station MVP-WDS - page 28

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 22 MVP-WDS Wall Docking Station for MVP Panels 4. Carefully remov e the cradle piv ot’ s attachment screw and place it aside for later re-attachment. 5. Carefully slide the black piv ot cradle combo unit (battery cover/support cradle) up from the metallic housing and use the screwdri ver t ...

  • AMX Wall Docking Station MVP-WDS - page 29

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 23 MVP-WDS Wall Docking Station for MVP Panels 8. Carefully place the first circuit board aside and rota te the black piv ot combo unit over to expose the second circuit board attached to the backside of the unit ( B in FIG. 25). 9. Carefully remove this second board by unscrewing the three ...

  • AMX Wall Docking Station MVP-WDS - page 30

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 24 MVP-WDS Wall Docking Station for MVP Panels 5. Use the scre wdriv er to install one of the previous ly remo ved MVP Support Cradle Securing scre ws to the securing plate (shown in FIG. 24 on pa ge 22). 6. Carefully slide the entire silver battery pi vot combo unit into the black WDS metal ...

  • AMX Wall Docking Station MVP-WDS - page 31

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 25 MVP-WDS Wall Docking Station for MVP Panels  Open the Battery Compartment by pressing down on the Battery Compartment Latch and then pulling the cov er outwards.  Press the Cradle Acti vation pushb utton (the sma ll recessed white button lo cated near the pins in Battery Slot #2) to ...

  • AMX Wall Docking Station MVP-WDS - page 32

    MVP-WDS Wall Docking Station & CB-MVPWDS Rough-In Box 26 MVP-WDS Wall Docking Station for MVP Panels ...

  • AMX Wall Docking Station MVP-WDS - page 33

    Upgrading the Docking Station Firmw are 27 MVP-WDS Wall Docking Station for MVP Panels Upgrading the Docking Station Firmware The following accessory de vices are firmware upgradeable:  MVP-TDS T able T op Dockin g Station ( FG5965-10 )  MVP-WDS W all/Flush Mount Docking Station - Black ( FG5965-11 )  MVP-WDS W all/Flush Mount Docking Stat ...

  • AMX Wall Docking Station MVP-WDS - page 34

    Upgrading the Docking Station Firmware 28 MVP-WDS Wall Docking Station for MVP Panels Step 2: Upgrade t he Docking Station firmware v ia USB 1. Configure the panel for a USB Connection T ype. 2. Prepare NetLinx Studio for comm unication to the panel v ia a V irtual Master . 3. After the Communication V erification dialog windo w verifies acti ve co ...

  • AMX Wall Docking Station MVP-WDS - page 35

    Upgrading the Docking Station Firmw are 29 MVP-WDS Wall Docking Station for MVP Panels 10. Click the Reboot Device checkbox. This cause s the touch panel to reboo t after the firmware update process is complete. The r eboot of the panel can take up 30 seconds after the f irmwar e pr ocess has finished. 11. Click Send to begin the transfer . The fil ...

  • AMX Wall Docking Station MVP-WDS - page 36

    Upgrading the Docking Station Firmware 30 MVP-WDS Wall Docking Station for MVP Panels Although firmware u pgrades can be don e over wirele ss Ethernet; it is recommended that firmware KIT files be transfer red over a direct USB connection and only when the panel is connected to a power supply . If battery power or wireless connection fails during a ...

  • AMX Wall Docking Station MVP-WDS - page 37

    Upgrading the Docking Station Firmware 31 M VP-WDS Wall Docking Station for MVP Pan els ...

  • AMX Wall Docking Station MVP-WDS - page 38

    12/08 © 2008 AMX. All rights reserved. AMX a nd the AMX logo are regist ered trademarks of AMX. AMX rese rves the right to alter specific ations without no tice at any time. It’s Your World - Take Con trol™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support ? ...

メーカー AMX カテゴリー Car Video System

AMX Wall Docking Station MVP-WDSのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- Wall Docking Station MVP-WDSの取扱説明書
- AMXの製品カード
- パンフレット
- またはAMX Wall Docking Station MVP-WDSの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、AMX Wall Docking Station MVP-WDSの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、AMX Wall Docking Station MVP-WDSの取り付け説明書、サービスマニュアル、簡易説明書、またはAMX Wall Docking Station MVP-WDSのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、AMX Wall Docking Station MVP-WDSの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

AMX Wall Docking Station MVP-WDSデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAMX Wall Docking Station MVP-WDSを使用するのを助ける技術的文書のことです。説明書は通常、全てのAMX Wall Docking Station MVP-WDSユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

AMXの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. AMX Wall Docking Station MVP-WDSの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAMX Wall Docking Station MVP-WDSの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。AMX Wall Docking Station MVP-WDSに関してこのドキュメントで見つけることができる全てのヒントの目次
3. AMX Wall Docking Station MVP-WDSデバイスの基本機能を使うにあたってのヒント。 AMX Wall Docking Station MVP-WDSのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。AMX Wall Docking Station MVP-WDSに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAMX Wall Docking Station MVP-WDSのメーカー/サービスへの連絡先に関する情報。

AMX Wall Docking Station MVP-WDSについてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもAMX Wall Docking Station MVP-WDSの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAMX Wall Docking Station MVP-WDSで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)