-
Sun Microsystems 1500 - page 1
Sun Microsystems, Inc. 4150 Network Circle Santa Clara, CA 95054 U .S.A. 650-960-1300 Send comments about this document to: docfeedback@sun.com Sun Blade™ 1500 Ser vice , Diagnostics , and T roub leshooting Manual Pa r t No . 816-7564-10 April 2003, Revision A EXAMPLE DOCUMENT ...
-
Sun Microsystems 1500 - page 2
Chapter 11 Replacing the Motherboard and Associated Components 11-3 FIGURE 11-1 DIMM Location and Identification Depending upon the configuration of your workstation, you can either add or replace memory . In either case, the new DIMMs must meet the Sun workstation requir ements. T ABLE 1 1- 1 lists the acceptable DIMM pair configurations. When you ...
-
Sun Microsystems 1500 - page 3
Chapter 13 Replacing Chassis Components 13-15 Y ou can also view an animated version of these instructions by clicking on this film icon. 13.3.1 Identifying the Rear Fan The front and r ear fans on the Sun Blade 1500 workstation are contained in green brackets. Both fans must be operating to adequately cool the components in a closed chassis. Both ...
-
Sun Microsystems 1500 - page 4
12-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 12-13 Smart Car d Reader Location and Identification 12.3.2 Removing the Smart Car d Reader 1. Power off the system, open the chassis, and remove the bezel. Refer to: ■ “Powering Off the W orkstation” on page 10-4 ■ “Removing the Access Panel” on ...
-
Sun Microsystems 1500 - page 5
Chapter 14 Replacing Internal Cables 14-7 14.2.1 Identifying the DVD-ROM Drive Interface Cable The DVD-ROM has separate power and interface cables. The power cable is a Y cable that connects to the motherboard at IDE PWR and the other ends to the hard drives and DVD-ROM drive. The interface cable connects the DVD-ROM drive to the motherboard at IDE ...
-
Sun Microsystems 1500 - page 6
Chapter 14 Replacing Internal Cables 14-15 3. Disconnect the IDE power cables from the upper hard drive HDD0 . See FIGURE 14-12 . FIGURE 14-12 Disconnecting the IDE Power Cable Fr om the Hard Drive(s) 4. If installed, disconnect the IDE power cable from the lower hard drive HDD1 . See FIGURE 14-12 . 5. Disconnect the IDE power cable from the DVD-RO ...
-
Sun Microsystems 1500 - page 7
14-10 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 14.3 Replacing the Har d Drive Interface Cable This section describes removal and installation of the hard drive interface cables. T opics include: ■ “Identifying the DVD-ROM Drive Interface Cable” on page 14-7 ■ “Removing the DVD-ROM Drive Interface Cabl ...
-
Sun Microsystems 1500 - page 8
Chapter 11 Replacing the Motherboard and Associated Components 11-5 FIGURE 11-3 Pressing the Catch on the Rear Fan Bracket 4. Slide the duct up until it is f lush with the edge of the rear fan bracket. See FIGURE 1 1-4 . FIGURE 11-4 Sliding the Duct Up 5. Flip the duct up and over to the back of the chassis, so that it is 180 degrees opposite of it ...
-
Sun Microsystems 1500 - page 9
Chapter 10 Preparing to Replace Components 10-15 FIGURE 10-9 Bezel Location and Identification 3. Release the lower mounting tabs. Carefully move the lower pair of mounting tabs apart, and then push them forwar d slightly . See FIGURE 10-10 . FIGURE 10-10 Releasing the Bezel Mounting T abs As you do this, you should see the bottom of the bezel move ...
-
Sun Microsystems 1500 - page 10
11-16 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 11-15 Pr essing Down on the Clip Latch b. Slide the clip to unhook the end opposite the latch. This relieves clip pr essure. c. Rotate the clip away from the CPU fan and heatsink assembly and lift it off the locking ring. Set the clip aside. If removing clip ...
-
Sun Microsystems 1500 - page 11
11-22 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 1 1.3.1 Identifying the Battery FIGURE 1 1-23 shows the location of and identifies the battery . FIGURE 11-23 Battery Location and Identif ication T ABLE 1 1- 1 lists the battery specifications. 1 1.3.2 Removing the Battery 1. Power off the system, open and positio ...
-
Sun Microsystems 1500 - page 12
11-36 Sun Blade 1500 Service, Diagnostics, and Troubleshooting Manual • April 2003 FIGURE 11-34 Identifying the PCI Car d Slots 3. Swing out the PCI card support. Squeeze the inside tabs together and swing the PCI card support out. See FIGURE 1 1-35 . PCI4 (66 MHz, 64-bit) PCI3 (33 MHz, 64-bit) PCI2 (33 MHz, 64-bit) PCI1 (33 MHz, 32-bit) PCI0 (33 ...
-
Sun Microsystems 1500 - page 13
Chapter 11 Replacing the Motherboard and Associated Components 11-45 FIGURE 11-42 Removing Cables Fr om the Routing Clips 9. Disconnect the power and signal cables. Disconnect the following power and signal cables from the corresponding motherboard connectors and set them out of the way of the motherboard. See FIGURE 1 1-41 . ■ Power supply cable ...
-
Sun Microsystems 1500 - page 14
Chapter 13 Replacing Chassis Components 13-45 FIGURE 13-48 Removing the PCI Car d Support Note – Do not use the chassis cross brace as a handle. Proceed to “Installing the PCI Card Support” on page 13-45. Note – Do not operate the workstation without the PCI card support installed. 13.7.3 Installing the PCI Car d Support 1. Open the chassis ...
-
Sun Microsystems 1500 - page 15
Chapter 15 Finishing Component Replacement 15-9 FIGURE 15-8 Reconnecting the Keyboard, Mouse, Monitor , and Network Connections 2. Reconnect any other external peripherals. 3. Power on those peripherals. Note – The monitor must be powered on before the system so that the monitor can communicate with the graphics accelerator when the system powers ...
Sun Microsystems 1500についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもSun Microsystems 1500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSun Microsystems 1500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。