Makita ARBOR 2711の取扱説明書

35ページ 2.11 mb
ダウンロード

ページに移動 of 35

Summary
  • Makita ARBOR 2711 - page 1

    Table Saw Arbor thole 255 mm (10") MODEL 2711 With Electric Brake No load Dimensions Ne, Blade Cutt,ng CaPdCmeF Table size IL x WI Sliding table IL x W x HI wetghf 255 mn, 91 mm 63 nirn 600 mm x 405 inmi 295 mm x 497 mm 3 800 1090 mm x 715 mm x 470 mm 32 5 kg 90" 45" Fixed table dldnlPtel iio"i 13 9 16'1 12 1 z 'I 123 ...

  • Makita ARBOR 2711 - page 2

    For Your Own Safety Read Instruction Manual Before Operating Table Saw GENERAL SAFETY PRECAUTIONS (For All Tools) 1 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. KNOW YOUR POWER TOOL. Read the owner's manual carefully. Learn the tools applications and limitations, as well as the specific potential hazards peculiar to it. KEEP GUARDS IN PLACE and in working ...

  • Makita ARBOR 2711 - page 3

    17. USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons. 18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. 19. CHECK DAMAGED PARTS. Before further use of the tool, a guard o ...

  • Makita ARBOR 2711 - page 4

    G R 0 U N D I N G INSTRUCT IONS ALL GROUNDED, CORD-CONNECTED TOOLS: In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord hav- ing an equipment-grounding conductor and a grounding plug. The plug must be plugged ...

  • Makita ARBOR 2711 - page 5

    ADDITIONAL SAFETY RULES 1. Wear eye protection. 2. Don't use the tool in presence of flammable liquids or gases. 3. Never use the tool with an abrasive cut-off wheel installed. 4. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 5. Clean the spindle, flanges (especially the installi ...

  • Makita ARBOR 2711 - page 6

    jam the blade in the workpiece, turn the tool off immediately. Unplug the tool. Then clear the jam. 18. Never remove cut-off pieces near the blade or touch the blade guard while the blade is running. 19. Don't abuse cord. Never yank cord to disconnect from receptacle. Keep cord away from heat, oil, water and sharp edges. SAVE THESE INSTRUCTION ...

  • Makita ARBOR 2711 - page 7

    Movement and transport of table saw Before moving the table saw, tighten the wing bolt to secure the sliding table. When moving the table saw, hold it by the fixed table and the bars. Be sure to use two persons to lift and move it. When transporting the table saw by vehicle, secure it with a rope or other sub- stantial means. ASSEMBLY The table saw ...

  • Makita ARBOR 2711 - page 8

    Installing miter gauge Insert the wooden gauge into the miter gauge and tighten the two screws lightly but firmly. The wooden gauge will be used later to help you accurately make cross- cuts. Place the miter gauge on the sliding table with the wooden gauge extending toward the fixed table. Insert the longer miter gauge installation screw through th ...

  • Makita ARBOR 2711 - page 9

    Install the blade between the two flanges. Then install the outer flange and hex nut onto the arbor, making sure the teeth of the blade are pointing down at the front of the table. To secure the blade in place, hold the outer flange with the offset wrench, then tighten the hex nut counterclockwise with the wrench. When tightening the hex nut, the o ...

  • Makita ARBOR 2711 - page 10

    Installing and adjusting rip fence Loosen the lever on the rip fence and fit the rip fence on the ruler guides. To check to be sure that the rip fence is parallel with the blade, secure the rip fence 2 - 3 mm (5/64" - 1/8") from the blade. Raise the blade up to maximum elevation. Mark one of the blade teeth with a crayon. Measure the dist ...

  • Makita ARBOR 2711 - page 11

    Tighen the lever on the rip fence. If the rip fence is not secure enough, leave the lever in the tightened position and tighen the screw in the hole in the rear end of the rip fence clockwise. However, do not tighten the screw excessively, or the lever will be- come loose. I CAUTION : Be sure to adjust the rip fence parallel with the blade, or a da ...

  • Makita ARBOR 2711 - page 12

    Installing blade guard CAUTION : Before installing the blade guard, adjust the depth of cut to its maximum elevation. (Note: The depth of cut is adjusted to its maximum elevation when the table saw is shipped from the factory.) Temporarily tighten the bolts with the offset wrench. Check to be sure that the blade and spreader are in a straight line. ...

  • Makita ARBOR 2711 - page 13

    Positioning table saw Locate the table saw in a well lit and level area where you can maintain good footing and balance. It should be installed in an area that leaves enough room to easily handle the size of your workpieces. The table saw should be secured with four screws or bolts to the work bench or table saw stand (optional accessory) using the ...

  • Makita ARBOR 2711 - page 14

    Hand tool storage pocket The table saw comes with a hand tool storage pocket in the base. Keep wrenches, screwdriver, etc. in this pocket. Adjusting depth of cut The depth of cut may be adjusted by turn- ing the knob. Turn the knob clockwise to raise the blade or counterclockwise to lower it. The depth of cut is indicated on the scale by the pointe ...

  • Makita ARBOR 2711 - page 15

    Bevel cutting Loosen the lock lever clockwise, then tilt the blade by swinging the knob until it reaches the desired angle (0 to 45 degrees). The bevel is indicated on the scale by the pointer (B). After obtaining the desired angle, tighten the lock lever counterclock- wise to secure the adjustment. CAUTION : After adjusting the bevel, be sure to t ...

  • Makita ARBOR 2711 - page 16

    Adjusting miter angle Loosen the miter gauge installation screws and adjust the miter gauge to the desired angle (0 to 45 degrees). Then tighten the miter gauge installation screws securely. CAUTION : After adjusting the miter angle, be sure to securely. tighten the miter gauge installation screws Switch action To start the tool, press the "ON ...

  • Makita ARBOR 2711 - page 17

    Operation CAUTION : *Make sure the blade guard works smoothly and properly for making both square cuts and bevel cuts before operation. *Never withdraw the workpiece while the blade is running. If you must withdraw the workpiece before completing a cut, first switch the tool off while holding the work- piece firmly. Wait until the blade has come to ...

  • Makita ARBOR 2711 - page 18

    Push block Use a 19 mm (3/4") piece of plywood. 120 .;.4-)fm11 mm (5") Faceledge parallel 6 mm (1/4"l 5o mm (2") (5") Handle should be in center of plywood piece. Fasten with glue and wood screws as shown. Small piece 9.5 mm x 8 mm x 50 mm (3/8" x 5/16" x 2") of wood must always be glued to plywood to keep th ...

  • Makita ARBOR 2711 - page 19

    Crosscutting CAUTION : When making a crosscut, remove the rip fence from the table. When cutting long or large workpieces, always provide adequate support to the sides of the table. The support should be at the same height as the table. (1; Loosen the wing bolt securing the sliding table. 0) Adjust the blade to 90 degrees to the table surface. Adju ...

  • Makita ARBOR 2711 - page 20

    The wooden gauge cannot be used for miter cutting. 19 mm (3/4") * 63" (2-1 /2") 19 mm (3/4") * 55mm (2-1/8") NOTE: Miter cutting capacity is less than crosscutting capacity. Make sure of the max miter cut- ting capacity before operation. The following reference table indicates some examples of miter cutting capacity. 260 mm ...

  • Makita ARBOR 2711 - page 21

    When a spacer block can be placed between the miter gauge and workpiece, you can obtain a greater miter cutting capacity. Ripping CAUTION When ripping, remove the miter gauge from the sliding table. .When cutting long or large workpieces, always provide adequate support behind the table. The support should be at the same height as the table. Before ...

  • Makita ARBOR 2711 - page 22

    i) When the width of rip is 150 mm (6") and wider, carefully use your right hand to feed the workpiece. Use your left hand to hold the workpiece in position against the rip fence. ii) When the width of rip is 65 mm - 150 mm (2-1/2" - 6") wide, use the push stick to feed the workpiece. iii) When the width of rip is narrower than 65 mm ...

  • Makita ARBOR 2711 - page 23

    Feed the workpiece by hand until the end is about 25 mm (I”) from the front edge of the table. Continue to feed using the push block on the top of the auxiliary fence until the cut is complete. 23 ...

  • Makita ARBOR 2711 - page 24

    MA1 NT ENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Cleaning Clean out sawdust and chips from time to time. Carefully clean the balde guard and moving parts inside the table saw. Lubrication To keep the table saw in tip-top running condition, and to assure maximu ...

  • Makita ARBOR 2711 - page 25

    ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool speci- fied in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner Dado head set (Part No 191 794-9) A dado is c ...

  • Makita ARBOR 2711 - page 26

    @ Use the chart below to select the proper cutters to obtain the various cutting widths. 114" I I 5116" 7/16" 112" 0 9/16" 518" 11116" 314" 1311 6" 0 Flange Ring I I I -* 10x2 I I -I Outslde ,',~~~e cutter cutter I I I + ox3 0 10x4 t- o 0 0 0 0 CAUTION : For a 1/8" cut width, the outside cutter ...

  • Makita ARBOR 2711 - page 27

    When installing two outside cutters without any inside cutter, be sure that the cutter tips do not face each other. 0 X @ While tightening the hex nut, be careful to maintain the even spacing between the tips of the inside cutters. @ When cutting 1/2" or narrower grooves, use the table insert originally installed on the table saw. When cutting ...

  • Makita ARBOR 2711 - page 28

    Featherbords are used to keep the work- piece in contact with the rip fence and table as shown, and to stop kickbacks. To install featherbords. proceed as follows : @ Turn the tool off and unplug it. @ Add 8" high flat facing board to the rip fence, the full length of the rip fence. @ Mount featherboards to the rip fence and table as shown, so ...

  • Makita ARBOR 2711 - page 29

    Ring (Part No. 257137-6) When cutting groove 1/4", 5/16", 3/8", 7/16", 1/2", 9/16" or 5/8", use this ring or rings. Table insert (Part No. 343396-9) When cutting grooves 9/16" or wider, use this table insert instead of the standard table insert. Table saw stand (Part No. STEX 122251 1 Place the stays on a lev ...

  • Makita ARBOR 2711 - page 30

    Saw blades 0 Chisel tooth combination saw blade For rip and cross-cut work. Most frequently used for general carpentry. Hole Part No. 255-7A I 255 (10") I 518'' I 36 1 792317-2 0 Carbide-tipped saw blade Fastest, smoothest longer sawing without blade sharpening cuts wood, drywall, plastic, hardwood, etc. Hole Part No. 0 Rip fence Par ...

  • Makita ARBOR 2711 - page 31

    Holder set (Part No. 191773-7) Convenient to attach for better support of long workpieces. Attach the holder to the reverse side of the I I CAUTION : Never attempt to lift or move the table saw while holding the holders. When moving the table saw, hold it by the fixed table and the bars. Hood set (Part No. 191793-1 ) When you wish to maintan clean ...

  • Makita ARBOR 2711 - page 32

    Jan 22 '87 US 255 mm (IO") TABLE SAW Model 2711 32 ...

  • Makita ARBOR 2711 - page 33

    Note. The switch and other part configurations may differ from country to country 33 ...

  • Makita ARBOR 2711 - page 34

    MODEL 2711 $FD DESCRIPTION Jan 22 87 US sD DESCRIPTION MACHINE ~ 2 3 4 5 6 7 8 9 IO 11 12 13 14 15 16 17 18 19 20 21 22 23 24 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 ~ 2 1 2 2 4 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 7 1 2 1 4 4 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 2 ...

  • Makita ARBOR 2711 - page 35

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...

メーカー Makita カテゴリー Saw

Makita ARBOR 2711のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- ARBOR 2711の取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita ARBOR 2711の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita ARBOR 2711の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita ARBOR 2711の取り付け説明書、サービスマニュアル、簡易説明書、またはMakita ARBOR 2711のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita ARBOR 2711の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita ARBOR 2711デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita ARBOR 2711を使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita ARBOR 2711ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita ARBOR 2711の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita ARBOR 2711の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita ARBOR 2711に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita ARBOR 2711デバイスの基本機能を使うにあたってのヒント。 Makita ARBOR 2711のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita ARBOR 2711に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita ARBOR 2711のメーカー/サービスへの連絡先に関する情報。

Makita ARBOR 2711についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita ARBOR 2711の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita ARBOR 2711で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)