-
Bryant TSTATBBNAC01-C - page 1
NOTE: Read the entire instruction manual before starting the installation. This symbol → indicates a change since the last issue. SAFETY CONSIDERATIONS Read and follow manufacturer instructions carefully. Follow all local electrical codes during installation. All wiring must conform to local and national electrical codes. Improper wiring or insta ...
-
Bryant TSTATBBNAC01-C - page 2
III. INSTALL THERMOSTAT WARNING: ELECTRICAL SHOCK HAZARD Failure to follow this warning could result in personal injury or death. Before installing thermostat, turn off all power to unit. There may be more than 1 power disconnect. 1. Turn OFF all power to unit. 2. If an existing thermostat is being replaced: a. Remove existing thermostat from wall. ...
-
Bryant TSTATBBNAC01-C - page 3
rate. However, a limiting feature will not allow more than 6 equipment cycles per hour, regardless of setting. Values can range from 1 to 9. Factory default setting is 3. This default selection will provide optimum performance in nearly all installations. Try it first. Do not change setting unless there is evidence of need to do so. Unlike conventi ...
-
Bryant TSTATBBNAC01-C - page 4
TO SELECT: 1. Enter configuration mode (if not already there). 2. Use up and down buttons to display Option 07. The SET icon should be off. 3. Press MODE button once. The SET icon will come on. The display now shows Option 07 setting. 4. Use up and down buttons to move between available Option 07 choices of ON or OF. Factory default is OF. 5. Press ...
-
Bryant TSTATBBNAC01-C - page 5
6. Use up and down buttons to select another Option, or press FAN button to exit configuration mode. M. Option 19 — Equipment Present This selection informs the thermostat of the heat, cool, and fan capabilities of the installed equipment. Select number 2, 3, or 4. Default is 4. For equipment with both heat and cool capability and fan selection, ...
-
Bryant TSTATBBNAC01-C - page 6
TABLE 2—NON-PROGRAMMABLE -C THERMOSTAT QUICK REFERENCE THERMOSTAT OUTPUT TSTAT Model Outdoor Unit Option 5 24v Hot Common Fan Heat Stage 1 Heat Stage 2 Heat Stage 3 Cool Stage 1 Cool Stage 2 Reversing Valve AC01-C AC N/A R C G W/W1 N/A N/A Y/Y2 N/A N/A HP01-C HP OFF R C G Y/Y2 W/W1 N/A Y/Y2 N/A O/W2/B HP01-C AC ON R C G W/W1 O/W2/B N/A Y/Y2 N/A N ...
-
Bryant TSTATBBNAC01-C - page 7
Fig. 8—Two-Speed Air Conditioner with Single-Stage Furnace A04009 24 V A C HO T 24 V A C COMM HEA T ST AGE 1 COOL ST AGE 2 FA N R C G W/W1 Y/Y2 R C N/A COOL ST AGE 1 N/A OUTDOOR SENSOR CONNECTION Y1 B S1 S2 C MODEL 2S 01-C THERMOST A T SINGLE-ST AGE FURNACE TW O-SPEED AIR CONDITIONER See notes 2, 5, 8, and 11 G W R Y Y2 Y1 HUM O/W2/B Fig. 6—Sin ...
-
Bryant TSTATBBNAC01-C - page 8
Fig. 12—Single-Speed Air Conditioner with Variable Speed (FK4D, FV, 40FK) Fan Coil R Y/Y2 R Y W/W1 W1 C MODEL AC 01-C THERMOSTAT EASY SELECT TERMINAL BOARD SINGLE-SPEED AIR CONDITIONE R J1 JUMPER J2 JUMPER See note 10 and 11 W2 Y/Y2 DH G G Y1 O C HEAT STAGE 1 24 VAC HOT C COOL STAGE 1 FAN 24 VAC COMM A98463 Fig. 10—Two-Speed Air Conditioner wit ...
-
Bryant TSTATBBNAC01-C - page 9
Fig. 14—Two-Speed Air Conditioner with Variable-Speed (FK4D, FV4, 40FK) Fan Coil A04012 24 V OL T HOT 24 V OL T COMM FA N COOL ST AGE 2 HEA T ST AGE 1 R Y/Y2 R Y2 C C C R Y1 MODEL 2S THERMOST A T EASY SELECT TERMINAL BOARD TWO-SPEED AIR CONDITIONER J1 JUMPER REMO VE J2 JUMPER FOR HEA T ST AGING See notes 2, 4, 8, 10, and 1 1 G G Y/Y2 DH W/W1 W1 H ...
-
Bryant TSTATBBNAC01-C - page 10
WIRING DIAGRAM NOTES: 1. Furnace must control its own second-stage heat operation via furnace control algorithm. Refer to indoor equipment Installation Instructions for proper setup. 2. See Option 5 information to convert HP and 2S thermostats to AC thermostat operation. 3. As an option, lock the furnace into low-heat operation and let O/W2/B contr ...
-
Bryant TSTATBBNAC01-C - page 11
OPERATIONAL INFORMATION FIVE-MINUTE COMPRESSOR TIMEGUARD This timer prevents the compressor from starting unless it has been off for at least 5 minutes. It can be defeated for 1 cycle by simultaneously pressing the FAN mode button and the INCREASE TEMPERATURE button. FIFTEEN-MINUTE CYCLE TIMER This timer prevents the start of a heating or cooling c ...
-
Bryant TSTATBBNAC01-C - page 12
A04105 NON-PROGRAMMABLE THERMOST A T CONFIGURA TION RECORD Date Owner/Operator A) Hardware Configuration Seal hole in wall. Thermostat Model No. B) Mode Settings C) Configuration Options Mode (Off , Heat, Cool, A uto , Eheat) Heating Set P oint V alue Cooling Set P oint V alue F an (Auto or On) 1 Anticipator (1-9: factory default = 3) 2 Clean Filte ...
Bryant TSTATBBNAC01-Cについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもBryant TSTATBBNAC01-Cの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBryant TSTATBBNAC01-Cで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。