Porter-Cable 877の取扱説明書

17ページ 0.23 mb
ダウンロード

ページに移動 of 17

Summary
  • Porter-Cable 877 - page 1

    T wo-Speed Cor dless Hammer Drill/Drivers Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for futur e reference. Model No. ______________________________________ T ype ___________________________________________ Serial No. _____________________________ ...

  • Porter-Cable 877 - page 2

    2 GENERAL SAFETY RULES FOR ALL BA TTER Y OPERA TED TOOLS WARNING! READ AND UNDERST AND ALL INSTRUCTIONS. Failure to follow all instructions listed below , may result in electric shock, fire and/or serious personal injury . WARNING: SOME DUST CREA TED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER CONSTRUCTION ACTIVITIES contains chemicals ...

  • Porter-Cable 877 - page 3

    3 3. Avoid accidental starting. Be sur e switch is in the locked or off position before inserting battery pack. Carrying tools with your finger on the switch or inserting the battery pack into a tool with the switch on invites accidents. 4. Remove adjusting keys or wrenches befor e turning the tool on. A wrench or a key that is left attached to a r ...

  • Porter-Cable 877 - page 4

    4 SPECIFIC SAFETY RULES AND SYMBOLS 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wir e will also make exposed metal parts of the tool “live” and shock the operator . 2. There ar e certain applications for which this tool was designed. Porter ...

  • Porter-Cable 877 - page 5

    5 5. Do not abuse cord. Never carry char ger by cord or yank it to disconnect from r eceptacle. Pull by plug rather than cord when disconnecting char ger . Have damaged or worn power cord and strain reliever r eplaced immediately . DO NOT A TTEMPT TO REP AIR POWER CORD. 6. Make sure cor d is located so that it will not be stepped on, tripped over , ...

  • Porter-Cable 877 - page 6

    6 ADDITIONAL SAFETY RULES FOR HAMMER-DRILLS 1. Apply forward for ce only on pistol grip handle and ONL Y with your hands when drilling. 2. Do not use bits lar ger than those recommended. They may cause personal injury due to jamming and loss of control. Lar ge bits may also overload the drill and damage the motor and gears. 3. V erify that the mode ...

  • Porter-Cable 877 - page 7

    7 INST ALLING AND REMOVING DRILL AND SCREWDRIVER BITS 1. CAUTION: Always set reversing button to center (locked OFF) position when installing and removing bits. 2. The three-jaw chuck is designed for self-centering of the bit. Open jaws lar ge enough by turning outer sleeve (A) Fig. 2, counterclockwise, when viewing the chuck from the bit end, so t ...

  • Porter-Cable 877 - page 8

    8 DRIVER BIT STORAGE Convenient storage areas with r etaining clip (B) Fig. 4, for screwdriver bits ar e provided on each side of the tool. OPERA TION CHARGING THE BA TTER Y P ACK GENERAL Before using your cor dless tool for the first time, the battery pack should be fully char ged. If the battery pack is installed in the tool, remove it by followi ...

  • Porter-Cable 877 - page 9

    9 DIAGNOSTICS The Models 8604 and 8624 char gers are equipped with a diagnostic system that automatically checks the battery pack each time a pack is inserted into the char ger . If no problems ar e found, the charger will automatically switch to “Fast Char ge” mode as described in NORMAL CHARGING. If a problem is found, it will be indicated by ...

  • Porter-Cable 877 - page 10

    10 HOW TO HOLD THE HAMMER DRILL/DRIVER WARNING: The front end of the Hammer Drill/Driver may be made live if the tool drills into live wiring in the wall. TO PREVENT ELECTRICAL SHOCK, THE HAMMER DRILL/DRIVER MUST BE HELD AS SHOWN IN FIG. 7. GENERAL DRILLING 1. Set torque adjusting collar for drilling operation and set speed selector to appropriate ...

  • Porter-Cable 877 - page 11

    11 DRILLING WOOD In addition to the instructions listed under GENERAL DRlLLlNG, the following also apply: 1. When using twist drills in wood, they should be withdrawn from the hole frequently to clear chips built up in flutes to avoid overheating and burning work. 2. If a backing block is used to keep back of work from splintering, it should be cla ...

  • Porter-Cable 877 - page 12

    12 2. Install proper bit that fits scr ew to screwdriver . 3. Set torque adjusting collar for desir ed torque and set speed selector to LOW . 4. Set screwdriver for corr ect rotation. 5. Start screw straight in hole with fingers. 6. Place bit on screw , start screwdriver and exert pressur e to drive screw . 7. As soon as screw has seated, lift scr ...

  • Porter-Cable 877 - page 13

    13 CAUTION: Extr eme care should be taken in the event bit should become jammed in the hole so that drill can be stopped immediately . See ADDITIONAL SAFETY RULES FOR HAMMER DRILL/DRIVERS, Number 7. MAINTENANCE KEEP TOOL CLEAN All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could very poss ...

  • Porter-Cable 877 - page 14

    14 5. Place the short end of a large allen wr ench ( 1 / 4 " or larger) into the chuck. Align wrench flats with chuck jaws and tighten chuck secur ely . While supporting chuck on a solid surface, position allen wrench to left (see Fig. 9) and strike wrench a sharp blow with a hammer to loosen chuck. T ur n chuck counterclock-wise to r emove. 6 ...

  • Porter-Cable 877 - page 15

    15 NOTES 900470 - 11-30-00.QXD 9/25/02 11:10 AM Page 15 ...

  • Porter-Cable 877 - page 16

    16 PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter -Cable warrants its Professional Power T ools for a period of one year from the date of original purchase. W e will repair or replace at our option, any part or parts of the pr oduct and accessories covered under this warranty which, after examination, proves to be defective in workmanship or materia ...

  • Porter-Cable 877 - page 17

    The following are trademarks of PORTER-CABLE · DEL T A Corporation (Las siguientes son marcas registradas de PORTER-CABLE · DEL T A S.A.) (Les marques suivantes sont des marques de fabriquant de la POR TER-CABLE · DEL T A Corporation): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORT A-BAND ® , PORT A-PLANE ® , PORTER-CABLE ® , ...

メーカー Porter-Cable カテゴリー Cordless Drill

Porter-Cable 877のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 877の取扱説明書
- Porter-Cableの製品カード
- パンフレット
- またはPorter-Cable 877の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Porter-Cable 877の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Porter-Cable 877の取り付け説明書、サービスマニュアル、簡易説明書、またはPorter-Cable 877のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Porter-Cable 877の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Porter-Cable 877デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPorter-Cable 877を使用するのを助ける技術的文書のことです。説明書は通常、全てのPorter-Cable 877ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Porter-Cableの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Porter-Cable 877の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPorter-Cable 877の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Porter-Cable 877に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Porter-Cable 877デバイスの基本機能を使うにあたってのヒント。 Porter-Cable 877のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Porter-Cable 877に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPorter-Cable 877のメーカー/サービスへの連絡先に関する情報。

Porter-Cable 877についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPorter-Cable 877の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable 877で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)