Audiobahn A12001DTの取扱説明書

20ページ 1.67 mb
ダウンロード

ページに移動 of 20

Summary
  • Audiobahn A12001DT - page 1

    CLASS D AMPLIFIERS A18001DT A12001DT A8001DT OPERA TING INSTR UCTIONS PLEASE RET AIN MANU AL FOR FUTURE USE AND REFERENCE QU ALITY , RELIABILITY , & PURE BLISS ...

  • Audiobahn A12001DT - page 2

    The Audiobahn W ay T o bring the product to market that excites the consumer through sound and vision from an orientation of integrity and customer service. We make you look as good as you sound. We strive to take car audio to an extreme the world has never seen, and a world that never stops evolving. Audiobahn was established in 1997 with one long ...

  • Audiobahn A12001DT - page 3

    Table of Contents Table of Contents 2 Introduction Features and Specifications Control and Functions Planning / Mounting Your System Adjusting and Tuning Troubleshooting Wiring Diagram Warning and Disclaimer Bridging 2 Amplifiers 3 4 5-10 11 12 16 15 17 13-14 Warranty 18-19 ...

  • Audiobahn A12001DT - page 4

    Introduction Dear Customer , Congratulations on your purchase of the worlds finest brand of car audio products. Here at Audiobahn Inc. we are devoted to making our musical reproduction the vert best, and we are pleased you have chosen our product. Through years of engineering expertise, hand craftsmanship, and critical testing procedures, we have c ...

  • Audiobahn A12001DT - page 5

    1-CHANNEL HIGH OUTPUT CLASS D AMPLIFIER DOUBLE SIDED CIRCUIT BOARD DUAL COOLING FANS VARIABLE LOW PASS FILTER REMOTE BASS BOOST CONTROL DIGITAL DISPLAY VOLT-METER L.E.D. ILLUMINATED HEAT SINK VAIRIABLE LOW PASS FILTER 50Hz - 150Hz VARIABLE BASS BOOST 0 - 18dB INPUT SENSITIVITY 200mV to 8V TYPICAL CURRENT DRAW 1.4 AMPS POWER OUTPUT A8001DT 1600 WATT ...

  • Audiobahn A12001DT - page 6

    Controls and Functions 5 ...

  • Audiobahn A12001DT - page 7

    Controls and Functions 6 This plug connects the amplifier and the remote bass knob using the supplied cable. This control adjusts the amplifier's input sensitivity . The input sensitivity is variable from 200 Millivolts to 8 volts. T urning clockwise increases sensitivity . T urning counter clockwise decreases sensitivity . This knob is not a ...

  • Audiobahn A12001DT - page 8

    Controls and Functions 7 The LINE OUT allows you to build a multiple amplifier system without having to use splitter cords or Y -adapters to distribute the signal. Now it is simply a matter bringing one set of RCAs into the first amplifier , then using the line out RCA jacks as the feed to the next amplifier . By using the bass boost function, bass ...

  • Audiobahn A12001DT - page 9

    8 Controls and Functions For use as a dedicated subwoofer channel, set the filter switch to the "LPF" (Low Pass Frequency). Adjust the variable crossover frequency with control knob as desired. The amplifier input circuit filters out everything above 50Hz ... 150Hz (dependant on the adjustment of the frequency control), so only the lowest ...

  • Audiobahn A12001DT - page 10

    Controls and Functions 9 These terminals are used to wire your subwoofer(s) to the amplifier . T o avoid unwanted ignition noise caused by ground loops, it is essential that the amplifier be grounded to a clean, bare, metal of the vehicle's chassis. This metal surface should be solid, strong and connected directly to the frame of the car . Not ...

  • Audiobahn A12001DT - page 11

    Controls and Functions 10 The remote terminal needs to be wired to the car's stereo or source unit remote turn on wire. This amplifier is turned on remotely when the vehicle's stereo is turned on. NOTE: iF YOUR RADIO DOES NOT HA VE A +12 VOL T OUTPUT LEAD WHEN THE CAR IS TURNED ON, THE "REMOTE" TERMINAL ON THE AMPLIFIER CAN BE C ...

  • Audiobahn A12001DT - page 12

    b. Are your components matched? The RMS power rating of your speakers must be equal or greater than the Amplifier's. They also must be 1-8 Ohms impedance (this information is normally printed on the speaker magnet). c. Consider both the length of your leads, and routing when determining the mounting location. Pre-Amp input Jacks require a leng ...

  • Audiobahn A12001DT - page 13

    Wiring Diagram 12 MONO MODE ...

  • Audiobahn A12001DT - page 14

    Bridging 2 Amplifiers 13 Master Slave Master Slave BRIDGED BRIDGED IF BRIDGED SWITCH POSITION IS ON SLA VE, ALL CONTROLS ARE NON-FUNCTIONAL. ALL CONTROLS ARE NOW CONTROLLED BY THE MASTER AMPLIFIER. HEAD UNIT ...

  • Audiobahn A12001DT - page 15

    Bridging 2 Amplifiers 14 ...

  • Audiobahn A12001DT - page 16

    Adjusting and T uning 15 ADJUSTING THE GAIN / LEVEL SETTING Below you will find information on adjusting the amplifiers gains. Adjusting the gain correctly is essential to proper operation of the amplifie r . If the gain is not adjusted properly it can and will lead to damage of the amplifier and connected speakers and will void your MANU F ACTURER ...

  • Audiobahn A12001DT - page 17

    Separate speaker wires and insulate Speaker wires short STATUS LAMP ON Temperature shut down Be sure proper speaker load impedance recommendations are observed. (If you use an ohmmeter to check speaker resistance, please remember that DC resistance and AC impedance may not be the same.) AMP TURNING OFF MEDIUM/HIGH VOLUME impedance Check speaker loa ...

  • Audiobahn A12001DT - page 18

    Investigate the layout of your automobile thoroughly before drilling or cutting any holes. T ake care when you work near the gas tanks, lines, hydraulic lines, and electrical wiring. Do not use the power amplifier unmounted. Attach the system securely to the automobile to prevent damage, particularly in the event of an accident. Do not mount the sy ...

  • Audiobahn A12001DT - page 19

    W arranty       18 ...

  • Audiobahn A12001DT - page 20

    How to receive warranty service: Contact your local Authorized Audiobahn Dealer , or call Audiobahn at (800) 488-8595 between the hours of 9:00 AM and 5:00 PM PST . If you are having problems with your system, we recommend you check the product carefully and thoroughly to confirm that the product truly has a manufacturer defect; as opposed to abuse ...

メーカー Audiobahn カテゴリー Car Amplifier

Audiobahn A12001DTのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- A12001DTの取扱説明書
- Audiobahnの製品カード
- パンフレット
- またはAudiobahn A12001DTの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Audiobahn A12001DTの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Audiobahn A12001DTの取り付け説明書、サービスマニュアル、簡易説明書、またはAudiobahn A12001DTのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Audiobahn A12001DTの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Audiobahn A12001DTデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAudiobahn A12001DTを使用するのを助ける技術的文書のことです。説明書は通常、全てのAudiobahn A12001DTユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Audiobahnの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Audiobahn A12001DTの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAudiobahn A12001DTの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Audiobahn A12001DTに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Audiobahn A12001DTデバイスの基本機能を使うにあたってのヒント。 Audiobahn A12001DTのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Audiobahn A12001DTに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAudiobahn A12001DTのメーカー/サービスへの連絡先に関する情報。

Audiobahn A12001DTについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAudiobahn A12001DTの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAudiobahn A12001DTで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)