Wasp Wasp WPL305の取扱説明書

18ページ 0.58 mb
ダウンロード

ページに移動 of 18

Summary
  • Wasp Wasp WPL305 - page 1

    WPL305 Thermal Label Printer User’s Guide For Wasp T echnologies  DT /TT Printer  Copyright W asp Bar Code T echnologies 2004. All rights reserved. No part of this publication may be reproduced or t ransmitted in any form or by any means without the written permission of W asp Bar Code T echnologies. The informati on contained in this docum ...

  • Wasp Wasp WPL305 - page 2

    Contents 1. Introduc tion ......................................................................................... 1 2. Getting S t arted .................................................................................... 1 2.1 Unpacking and Inspection............................................ 1 2.2 Equipment Checklist ......................... ...

  • Wasp Wasp WPL305 - page 3

    1. Introduction Thank you for purchasing the W305 The rmal T ransfer and Direct Thermal Bar Code Printer . Although the printer take s only a small amount of sp ace, it delivers reliable, superior performance. This printer provides both thermal trans fer and direct thermal printing at user selectable speed of: 2.0, 3. 0, 4.0 or 5.0ip s. It acc epts ...

  • Wasp Wasp WPL305 - page 4

    2.3 Printer Part s Ribbon Access Window T op Cover Open Lever Feed Button Printer T op Cover LED Indicator Figure 1: Top front view 3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect the printer to the computer with the Centronics or USB cable. 4. Plug the power cord ...

  • Wasp Wasp WPL305 - page 5

    3.2 Loading the Ribbon The printer automatically detects if a ribbon is inst alled after power on and will switch to thermal transfer or direct t hermal pri nting mode. If printer does not detect the ribbon, the motor that drives the ribbon rewi nd spindle will be turned off. In case the ribbon is inst alled but the printer does not detect the ribb ...

  • Wasp Wasp WPL305 - page 6

    Figure 3: Ribbon installation 6. Attach the ribbon spindle to the Back Hub by placing the lef t side of the spindle against the knob with the sp ring on it and compressing with the ribbon spindle. Slide the right side down over the other knob. The ribbon spindle should not be able to be removed without re-compressing the spring. Y ou may have to tu ...

  • Wasp Wasp WPL305 - page 7

    Lower Cover Figure 5: Pull the lever to open the cover 3. Place the roll of labels onto t he center of the paper roll mount. Printer T op Cover Paper Roll Mount Support Bar Paper Guide Te f l o n B a r T op Cover Open Lever Figure 6: Label inst allation 4. Feed the paper , printing side face up, under the T eflon bar and the paper guide and pass ov ...

  • Wasp Wasp WPL305 - page 8

    cover . 2. Do not allow the top cover to slam closed. 3. Failure to securely close and lock th e cover will result in poor print quality . 3.7 T op Cover Operation T o Open: 1. When facing the front of the printer pull the cover release levers on both sides of the printer towards you. 2. Lift the top gradually . There are two stop positions for the ...

  • Wasp Wasp WPL305 - page 9

    when closing the top cover! Figure 8: T op cover is fully open and ready to close Figure 9: Use both hands to close the top cover 5. Do not force the cover! If you are not sure if top cover is locked at a stop position, please do not push top cover to close it or the top cover will be damaged. Instead, open the top cover as wide as it will go and c ...

  • Wasp Wasp WPL305 - page 10

    4. Power on Utilities There are three power-on utilities to set up and test printer hardware. 1. Printer initialization 2. Ribbon sensor calibration 3. Gap or black mark sensor calibration Note: Y ou must run the #2 and #3 utilities after running the #1 to properly set up the printer . 4.1 Initialization Printer initialization is used to clear DRAM ...

  • Wasp Wasp WPL305 - page 11

    4.2 Ribbon Sensor Calibration Note: Please make sure the ribbon is properly installed before doing this calibration. Please follow the steps below to calibrate the ribbon sensor . 1. T urn the printer power of f. 2. Press and hold the FEED butt on then turn on the printer . 3. The LED will turn orange then blink red 5 times. Release after the first ...

  • Wasp Wasp WPL305 - page 12

    Print head check pattern Firmware version Firmware checksum Printed mileage (meter) Serial port configuration Country code Print speed (inch/sec) Print darkness Label size (inch) Gap distance (inch) Gap/black mark sensor sensitivity Numbers of download files T otal & available memory space Figure 10: Self-test printout 10 ...

  • Wasp Wasp WPL305 - page 13

    The printer will enter dump m ode after printing the printer configuration. In dump mode, all characters will be printed in 2 columns as in the figure below . Hex decimal data related to left column of ASCII data ASCII Data Figure 1 1: Dump mode printout The left side characters are received from your system and the right side dat a are the corresp ...

  • Wasp Wasp WPL305 - page 14

    5. Maintenance 5.1 Cleaning Use one or more of the following supplies that meets your needs:  Cleaning pens  Cleaning swabs  Lint-free cloth Printer Part Method Printer Head  Let the print head to cool for one minute.  Use a cleaning pen to swab the print elements. Platen Roller  Rotate the platen rolle r and wipe it thoroughly wi ...

  • Wasp Wasp WPL305 - page 15

    The printer is paused. 3. 4.  Press the feed button to resume printing. The printer is out of label or ri bbon or the printer settings are not correct Out of label or ribbon  Load a roll of labels and follow the instructions in Loading the Labels , then press the feed button to resume printing.  Load a ribbon and follow the instructions in ...

  • Wasp Wasp WPL305 - page 16

    7. Specifications 7.1 Printer Specifications Item W305 Mech ani sm Resolution 203 dpi. Max. Print Width 108 mm. Max. Print Length 1000 mm ( 39” ). Ribbon Capacity 300 meter with 1” core. (Max. OD 67 mm) Printing S peed 2, 3, 4 and 5 ips. Peeler function 2, 3 ips Printing Method Direct thermal and thermal transfer printing. Enclosure S tructure ...

  • Wasp Wasp WPL305 - page 17

    2D: PDF-417, Maxicode, and DataMatrix. Command Set WPL Environment Operation T emperature: 5 ~ 40. Relative Humidity: 25% ~ 85% (Non Condensing). S torage T emperature: -40 ~ 60. Relative Humidity: 10% ~ 90% (Non Condensing). 7.2 Label Stock Specifications Item Specification T ype Label (Continuous , Die-cut , Fan-fold). Wound T ype Out ...

  • Wasp Wasp WPL305 - page 18

    16 8. Product Support If you experience any problems with your W asp printer that you are unable to resolve, use our online support site to register th en call for technical assistance at (214) 547-4100, Monday through Friday , 8:00 AM – 5:00 PM Central Standard T ime. Y ou must register to be eligible for technical support. Our web site is www . ...

メーカー Wasp カテゴリー Printer

Wasp Wasp WPL305のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WPL305の取扱説明書
- Waspの製品カード
- パンフレット
- またはWasp Wasp WPL305の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Wasp Wasp WPL305の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Wasp Wasp WPL305の取り付け説明書、サービスマニュアル、簡易説明書、またはWasp Wasp WPL305のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Wasp Wasp WPL305の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Wasp Wasp WPL305デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがWasp Wasp WPL305を使用するのを助ける技術的文書のことです。説明書は通常、全てのWasp Wasp WPL305ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Waspの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Wasp Wasp WPL305の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははWasp Wasp WPL305の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Wasp Wasp WPL305に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Wasp Wasp WPL305デバイスの基本機能を使うにあたってのヒント。 Wasp Wasp WPL305のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Wasp Wasp WPL305に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるWasp Wasp WPL305のメーカー/サービスへの連絡先に関する情報。

Wasp Wasp WPL305についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもWasp Wasp WPL305の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがWasp Wasp WPL305で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)