Kettler 7176-000-090-500の取扱説明書

28ページ 2.48 mb
ダウンロード

ページに移動 of 28

Summary
  • Kettler 7176-000-090-500 - page 1

    Match 5.0 T able T ennis T able Models 7136-000-500 & 7176-000- 090- 500 Printed on recycled paper . Made in Germany Picture Similar KETTLER ® International Inc. • 1355 London Bridge Road • Virginia Beach, V A 23453 USA www .kettlerusa.com info@kettlerusa.com Adult Assembly Required Please do not return this product to the store. Contact K ...

  • Kettler 7176-000-090-500 - page 2

    Note on Safety All KETTLER ® products are designed in accordance with the latest safety regulations and undergo a constant process of quality control during manufacturing. The knowledge gained in this process is used to constantly improve and develop our products. In order to offer our customers the very best in product quality , we reserve the ri ...

  • Kettler 7176-000-090-500 - page 3

    Before Assembly (continued) General Assembly Instructions • The equipment must be assembled with care by two adults. • Separate all the parts including the hardware. Compare quantities with the package contents section and that all items are undamaged. If there are any problems, please contact KETTLER ® . • Before assembling the equipment, s ...

  • Kettler 7176-000-090-500 - page 4

    Items below are shown at actual size Number Incl. - 1-6mm, 2-8mm Number Incl. - 2 (outdoor only) Number Included - 2 Number Included - 2 Number Included - 1 Number Included - 1 Number Included - 2 Number Included - 2 Number Included - 4 m8x125 Package Contents (continued) Number Included - 4 m8x1 10 Number Included - 4 m8x45 Number Included - 4 m6x ...

  • Kettler 7176-000-090-500 - page 5

    Package Contents (continued) Items below are shown at actual size Number Included - 18 m6 Number Included - 2 Number Included - 8 m8 Number Included - 8 Number Included - 4 Number Included - 8 m12x6x3 Number Included - 4 m26x19x6 Number Included - 2 m16x8x3 Number Included - 2 Number Included - 4 m12x6x15 Number Included - 8 Number Included - 2 Num ...

  • Kettler 7176-000-090-500 - page 6

    Assembly Begin the assembly of your table by carefully removing the plastic wrap and all of the loose contents. Separate the two table tops by removing the four plastic corner protectors and the plastic side strips. Step 1 2 Required Align footlock with stemtube. Insert drift pin. There are two footlocks and stemtubes. Assemble both as shown. A B C ...

  • Kettler 7176-000-090-500 - page 7

    Assembly Step 2 A B C D E F 4 Required 4 Required m8 8 Required dia 16x8 4 Required m8x125 4 Required dia 25x8 8 Required End view and perspective view 4 Required Paying attention to position of wheelbase, assemble the stemtubes to base in order shown. Insert endcaps. Assemble two wheelbase assemblies. 7 ...

  • Kettler 7176-000-090-500 - page 8

    J K L Assembly Step 2 (continued) G H I Photo K shows the non locking stemtube being installed. Step E to step J are the same for the locking and non locking stemtube. 8 ...

  • Kettler 7176-000-090-500 - page 9

    Step 3 Assembly Install non-locking wheels. Do not over torque; wheels should roll smoothly . Install non-locking wheels on both wheelbase assemblies. A B C D E 2 Required m8x1 10 8 Required dia 16x8 2 Required 8m 9 ...

  • Kettler 7176-000-090-500 - page 10

    Step 4 Assembly Install locking wheels. The grooves of wheels should face inward. Again, do not over torque; wheels should roll smoothly . Push down foot lock to lock the wheels.Install non-locking wheels on both wheelbase assemblies. A C D E 2 Required m8x1 10 8 Required dia 16x8 2 Required m8 10 B ...

  • Kettler 7176-000-090-500 - page 11

    Assembly Step 5 Paying attention to position of wheelbase, snap alignment struts into place. Bolt locking struts to base. Bolt the locking strut with thumb latch to the same side as locking wheels. Bolt strut without latch to the side of non-locking wheels. Assemble two identical wheelbase assemblies with wheels and struts. A B C D E F G H I 4 Requ ...

  • Kettler 7176-000-090-500 - page 12

    Assembly Step 6 Bolt one M8 crossbar between each wheelbase. This crossbar is being assembled temporarily to create a support base and will be removed at a later step. For outdoor tables only: slide the shimpad onto wheelbase (steps B, C, and D). The assembly thus far should match photo E. A B C D E M8 threads M6 threads 12 2 Required m8x45 ...

  • Kettler 7176-000-090-500 - page 13

    Assembly Step 7 Insert endcap into the bottom of netpost bar . Using M6 crossbar , assemble crossbar and netpost bars to alignment struts. The netpost bar installation is repeated on the other wheelbase assembly . Fastener quantities include installation on both wheelbase assemblies. The assembly thus far should match photo G. A B C D E F 2 Require ...

  • Kettler 7176-000-090-500 - page 14

    Assembly Step 8 Screw eyelets to four Jbars. Assemble safety levers to two of the Jbars. Slide handgrip onto safety lever . Note the orientation of the slot in the safety lever and the Jbar as shown in photo E. 4 Required dia 12x6 2 Required m6 4 Required 2 Required m6x30 2 Required A B C D E F G 4 Required 3.9x13 note position 14 ...

  • Kettler 7176-000-090-500 - page 15

    Assembly Step 9 Screw eyelets to support leg on table-top half. Repeat for second table-top half. 4 Required A B C 4 Required 3.9x13 Support Leg 15 ...

  • Kettler 7176-000-090-500 - page 16

    A B C D Step 10 Important: have two people complete steps 10-12. With assistance, lift one table top onto the wheelbase; the legs will be facing outward. Have one person support the top while it is resting on the base while the other completes assembly . Assemble crossbar to Jbars and support leg in the order shown. Note: a Jbar with safety lever s ...

  • Kettler 7176-000-090-500 - page 17

    A B C D Step 11 Raise safety lever up straight. Bolt the safety lever to leg. Bolt the Jbars to leg. Insert footcaps. E F Assembly 1 Required m6x37 2 Required dia 12x6 3 Required m6 1 Required m 16x8x3 G H I 2 Required m6x60 4 Required m 12x6x3 End view and side view shown - 2 Required m12x6x15 2 Required 17 m 16x8x3 m 12x6x3 Leg ...

  • Kettler 7176-000-090-500 - page 18

    Step 11 continued Assembly J K L Leg Step 12 Bolt locking struts to support leg. A B C D E F G 2 Required m6x49 2 Required m6 4 Required m12x6 18 Now , remove the temporary crossbar assembled in step 6. Carry out steps 10-12 again for the other side. ...

  • Kettler 7176-000-090-500 - page 19

    Assembly 19 A B C D T o properly open table into playing position: lock wheels (H), push the thumb latch down on the left locking strut. Squeeze the strut on the right side and lower table into playing position. Support the table as you lower it; never allow it to drop down. Open T able T op to Complete Assembly ...

  • Kettler 7176-000-090-500 - page 20

    A C D Step 13 Slide net post onto netpost bar and screw into place. Insert guide plug. Repeat on other side of table. Assembly 2 Required 4.8x25 2 Required A B Step 14 Attach ball/racquet holder to netpost. B 20 ...

  • Kettler 7176-000-090-500 - page 21

    A B Step 15 Screw sideshroud into place. Repeat installation of second shroud on opposite side wheelbase assembly . Assembly 6 Required 3.9x25 21 3 Screws ...

  • Kettler 7176-000-090-500 - page 22

    Assembly Net Assembly Net assembly: Slide Jpin through net.. Place Jpin in designated slots. T ie string to tension tab. Place string in slots over Jpin and net post. Adjust net tension by adjusting tension tab. Remove protective plastic film from table surface. A B C D 22 ...

  • Kettler 7176-000-090-500 - page 23

    Assembly 23 Folding T able Folding T able: T o properly fold the table, lock the wheels, press the safety lever up and lift top. Once the top is halfway up you can release lever and continue to fold the top. A B C Remove Film Remove protective plastic film from table surface. ...

  • Kettler 7176-000-090-500 - page 24

    THERE ARE NO W ARRANTIES, EXPRESSED OR IMPLIED, MADE BY EITHER THE DISTRIBUTOR OR THE MANUF ACTURER ON KETTLER ® PRODUCTS, EXCEPT THE MANUF ACTURER’S LIMITED W ARRANTY AGAINST DEFECTS IN MA TERIAL SET OUT BELOW: This KETTLER ® Limited W arranty applies to products sold through the KETTLER ® Authorized Dealer Network to the original retail purc ...

  • Kettler 7176-000-090-500 - page 25

    25 Ordering Spare Parts When ordering spare parts, always state the full model number , spare part number , the quantity required and the serial number . Example order: Model 7136-500/spare part number 70130761/qty 1/serial number… Important: Spare part prices do not include fastening materials; if fastening material (bolts, nuts, washers, etc.) ...

  • Kettler 7176-000-090-500 - page 26

    12 1 25 13 17 4 4 7 2 3 23 25 22 8 10 11 19 29 28 30 32 27 15 20 21 31 25 12 1 25 33 33 13 17 6 5 2 3 7 23 9 37 34 26 35 36 38 Spare Parts 26 ...

  • Kettler 7176-000-090-500 - page 27

    Spare Parts 1 T op 2 941301 17 94130125 2 Leg 2 941 1 1 138 941 1 1 129 3 Footcap 4 70130540 70130540 4 Clamp (outdoor table) 8 10128028 5 Clamp 25mm (indoor table) 4 941 10341 6 Clamp 18mm (indoor table) 4 941 10192 7 Support Leg 2 941 1 1 139 941 1 1 130 8 Wheelbase 2 941 1 1 142 941 1 1 142 9 Stemtube for non-locking wheel (3437) 2 70130812 7013 ...

  • Kettler 7176-000-090-500 - page 28

    KETTLER ® International Inc., 1355 London Bridge Road, Virginia Beach, V A 23453 USA www .kettlerusa.com • E-mail: info@kettlerusa.com For parts/service: call 866-804-0440 or e-mail parts@kettlerusa.com Docu 7 . 05 .1 1 ©201 1 KETTLER ® All rights reserved. No part of this manual may be reproduced, stored in a retrieval system, or transmitted ...

メーカー Kettler カテゴリー Table Top Game

Kettler 7176-000-090-500のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 7176-000-090-500の取扱説明書
- Kettlerの製品カード
- パンフレット
- またはKettler 7176-000-090-500の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Kettler 7176-000-090-500の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Kettler 7176-000-090-500の取り付け説明書、サービスマニュアル、簡易説明書、またはKettler 7176-000-090-500のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Kettler 7176-000-090-500の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Kettler 7176-000-090-500デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKettler 7176-000-090-500を使用するのを助ける技術的文書のことです。説明書は通常、全てのKettler 7176-000-090-500ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Kettlerの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Kettler 7176-000-090-500の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKettler 7176-000-090-500の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Kettler 7176-000-090-500に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Kettler 7176-000-090-500デバイスの基本機能を使うにあたってのヒント。 Kettler 7176-000-090-500のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Kettler 7176-000-090-500に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKettler 7176-000-090-500のメーカー/サービスへの連絡先に関する情報。

Kettler 7176-000-090-500についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもKettler 7176-000-090-500の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKettler 7176-000-090-500で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)