Poulan 415324の取扱説明書

32ページ 1.39 mb
ダウンロード

ページに移動 of 32

Summary
  • Poulan 415324 - page 1

    OWNER'S MANUAL MODEL NUMBER: 961980019 SNOW THROWER Always W ear Eye Protection During Operation IMPORT ANT MANU AL Do Not Throw Away WARNING: Read the Owner's Manual and fol low all W arnings and Safety In struc tions. F ail ure to do so can result in serious injury . 415324 Rev 1 09.19.07 TH Printed in the U.S.A. ...

  • Poulan 415324 - page 2

    2 IMPORT ANT Safe Operation Practices for W alk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. F ailure to observe the following safety instructions could result in serious injury . WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. Caution should be e ...

  • Poulan 415324 - page 3

    3 MAINTENANCE SCHEDULE ..................................... 13 SERVICE AND AD JUST MENTS ........................... 15-17 STORAGE ................................................................... 17 TROU BLE SHOOT ING ................................................ 18 REP AIR P ARTS ..................................................... 20-31 W ...

  • Poulan 415324 - page 4

    4 P ARTS P ACKED SEP ARA TEL Y IN CARTON ...

  • Poulan 415324 - page 5

    5 AS SEMBL Y / PRE-OPERA TION Read these instructions and this manual in its entirety before you attempt to assemble or operate your new snow thrower . Reading the entire manual will familiarize you with the unit, which will assist you in assembly , operation and maintenance of the product. Y our new snow thrower has been as sem bled at the factory ...

  • Poulan 415324 - page 6

    6 AS SEMBL Y / PRE-OPERA TION INST ALL AUGER CONTROL ROD (See Figs. 5 and 6) The auger control rod has the short loop on the end of the spring as shown. 1. Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown. 2. With top end of rod positioned under right side of control panel, push down on rod and insert ...

  • Poulan 415324 - page 7

    7 OPERA TION KNOW YOUR SNOW THROWER READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERA TING YOUR SNOW THROWER. Compare the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. These symbols may appear on your snow thrower or in literat ...

  • Poulan 415324 - page 8

    8 MEETS A.N.S.I. SAFETY REQUIREMENTS Our snow throwers conform to the standards of the American National Standards Institute. OPERA TION Drift cutter - used to cut through deep snowdrifts. Drive speed control lever – used to select forward or reverse motion and speed of snow thrower . T raction drive control lever – used to engage power -pro- p ...

  • Poulan 415324 - page 9

    9 The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your snow thrower or performing any ad just - ments or repairs. We recommend standard safe ty glasses or a wide vision safety mask worn over spectacles. HOW TO USE Y ...

  • Poulan 415324 - page 10

    10 TO MOVE FORWARD AND BACK WARD (See Fig. 14) SELF-PROPELLING, forward and reverse movement of the snow thrower , is controlled by the traction drive control lever located on the left side handle. • Squeeze traction drive control lever to handle to en gage the drive system. • Release traction drive control lever to stop the forward or reverse ...

  • Poulan 415324 - page 11

    11 OPERA TION TO ST ART ENGINE Y our snow thrower engine is equipped with both a 120 V olt A.C. electric starter and a recoil starter . The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 V olt A .C. household current. • Be sure your house is a 120 V olt A .C. three-wire ground ed system. If yo ...

  • Poulan 415324 - page 12

    12 WARM ST ART - ELECTRIC ST ARTER Follow the steps above, keeping the choke control in the “OFF” position. COLD ST ART - RECOIL ST ARTER 1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT turn the key . Keep the extra safety ignition key in a safe place. 2. Place ON / OFF switch in “ON? ...

  • Poulan 415324 - page 13

    13 MAINTENANCE GENERAL REC OM MEN DA TIONS The warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. T o receive full value from the warranty , operator must maintain snow thrower as in struct ed in this manual. Some ad just - ments will need to be made periodically to properly maintain your ...

  • Poulan 415324 - page 14

    14 MAINTENANCE V -BEL TS Check V -belts for deterioration and wear after every 50 hours of operation and replace if necessary . The belts are not ad just able. Replace belts if they begin to slip from wear . (See “TO REMOVE BEL T COVER” in the Service and Adjustments section of this manual). The V -belts on your snow thrower are of special con ...

  • Poulan 415324 - page 15

    15 WARNING: T o avoid serious injury , before performing any service or ad just ments: 1. Be sure the on/off switch is in the OFF position. 2. Remove safety ignition key . 3. Make sure the augers and all mov ing parts have completely stopped. 4. Disconnect spark plug wire from spark plug and place wire where it can not come in contact with plug. SN ...

  • Poulan 415324 - page 16

    16 SERVICE AND ADJUSTMENTS TO REPL ACE BEL TS (See Fig. 20) The auger and traction drive belts are not adjustable. If the belts are damaged or begin to slip from wear , they should be replaced. It is recommended that the belt(s) be replaced by a Sears service centre/department. NOTE: It is recommended that both the auger and traction drive belt be ...

  • Poulan 415324 - page 17

    17 STORAGE Immediately prepare your snow thrower for storage at the end of the season or if the unit will not be used for 30 days or more. WARNING: Never store the snow thrower with gaso line in the tank in side a build ing where fumes may reach an open flame, spark or pilot light as on a fur nace, water heater , clothes dryer or gas ap pli ance. A ...

  • Poulan 415324 - page 18

    18 TROUBLESHOOTING Does not start 1. Fuel shut-off valve (if so 1. T urn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition key 2. Insert safety ignition key . is not inserted. 3. Out of fuel. 3. Fill fuel tank with fresh, clean gasoline. 4. Throttle in STOP position 4. Move throttle to FAST position (or ON/OFF swit ...

  • Poulan 415324 - page 19

    19 SERVICE NOTES ...

  • Poulan 415324 - page 20

    20                                                       ...

  • Poulan 415324 - page 21

    21 KEY P ART NO . NO. DESCRIPTION 4 191079 Pulley , Impeller 5 188909 Bearing Assembly , Flange 6 155377 Nut, Hex Flange 5/16-18 7 180355 Bolt, Flat Head, Carriage 5/16-18 x 5/8 8 72270505 Bolt, Carriage 5/16-18 9 163183 Bolt, Hex Head 5/16-18 10 404929X428 Housing, Auger 11 404932X479 Bar , Scraper 12 178675X008 Bracket, Corner Discharge 13 175322 ...

  • Poulan 415324 - page 22

    22 3 2 1 1 2 6 19 2 2 26 28 27 27 25 20 29 7 4 5 6 8 8 16 18 17 10 14 3 13 15 9 11 12 31 32 30 REP AIR P ARTS SNOW THROWER - MODEL 961980019 (96198001900) CONTROL P ANEL / DISCHARGE CHUTE ...

  • Poulan 415324 - page 23

    23 KEY P ART NO . NO. DESCRIPTION 1 414280 Knob, Lever , Black 2 17501010 Screw #10-24 x 5/8 3 198475 Control, Cable, Deflector 4 73800600 Nut, Lock 3/8-16 5 19131316 Washer , Flat 3/8 6 404974 Control Assembly , Chute Rotater 7 405784X479 Support, Pivot 8 150078 Screw , Hex Head 5/16-18 x 3/4 9 184505 Spring, Deflector 10 179829 Bolt, Shoulder 11 ...

  • Poulan 415324 - page 24

    24 34 37 42 10 15 23 22 27 27 22 15 32 31 32 30 31 38 39 7 6 36 2 5 5 5 1 8 28 28 9 18 19 26 24 24 25 5 5 40 12 11 15 11 15 16 17 16 17 14 11 13 REP AIR P ARTS SNOW THROWER - MODEL 961980019 (96198001900) HANDLES ...

  • Poulan 415324 - page 25

    25 KEY P ART NO . NO. DESCRIPTION 1 412682X479 Lever , Auger Control, RH 2 412681X479 Lever , T raction Drive Control, LH 5 169675 Retainer , Hairpin 6 17060408 Screw , Hex Head 1/4-20 x 3/4 7 412677 Bail, Interlock 8 196333X008 Arm, Impeller Rod 9 412679X008 Arm, T raction Rod 10 412683X479 P anel, Control 11 74780524 Screw , Hex Head 5/16-18 x 1- ...

  • Poulan 415324 - page 26

    26 4 4 4 4 4 2 2 43 11 1 1 22 5 5 5 2 2 20 41 21 17 13 3 6 14 19 18 18 15 24 36 35 34 37 31 9 12 23 26 29 25 4 4 33 28 32 27 44 REP AIR P ARTS SNOW THROWER - MODEL 961980019 (96198001900) DRIVE ...

  • Poulan 415324 - page 27

    27 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO. DESCRIPTION 1 401619 Chain, Drive 2 751153 Nut, Lock 5/16-18 3 402882 Clip, Retainer 4 1 ...

  • Poulan 415324 - page 28

    28 6 19 17 10 21 22 23 2 3 4 6 42 8 9 12 13 15 27 26 25 24 18 7 20 14 5 40 46 44 49 50 51 52 35 34 33 38 37 39 43 11 32 32 36 36 44 45 41 30 29 31 31 11 11 1 5 5 5 16 56 47 53 10 21 28 57 6 58 REP AIR P ARTS SNOW THROWER - MODEL 961980019 (96198001900) CHAS SIS / ENGINE / PULLEYS ...

  • Poulan 415324 - page 29

    29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORT ANT : Use only Original Equipment Manufacturer (O.E.M.) replacement parts. F ailure to do so could be hazardous, damage your snow thrower and void your warranty . KEY P ART NO . NO. DESCRIPTION 1 414557 Spring, T raction Idler 2 180522 Pulley , Idler (2-1/4) 3 - - - Eng ...

  • Poulan 415324 - page 30

    30 3 2 7 7 5 5 6 6 4 7 1 2            REP AIR P ARTS SNOW THROWER - MODEL 961980019 (96198001900) WHEELS / DECALS ...

  • Poulan 415324 - page 31

    31 KEY P ART NO . NO. DESCRIPTION 1 187833X421 Wheel Assembly , 16", LH 2 155443 Pin, Klik 1/4 3 187865X421 Wheel Assembly , 16", RH 4 146315 Screw , Hex Head, T apping 5/16-18 x 5/8 5 179830 Bearing, Axle 6 174697 Washer , Thrust (1") 7 17490508 Screw , Hex Head 5/16-18 x 1/2 KEY P ART NO . NO. DESCRIPTION 1 181037 Decal, Danger 2 1 ...

  • Poulan 415324 - page 32

    LIMITED W ARRANTY The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and work man ship. For a period of two (2) years from date of purchase by the original consumer pur - chaser , we will repair or replace, at our option, without charge for parts or labor incurred in repl ...

メーカー Poulan カテゴリー Snow Blower

Poulan 415324のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 415324の取扱説明書
- Poulanの製品カード
- パンフレット
- またはPoulan 415324の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Poulan 415324の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Poulan 415324の取り付け説明書、サービスマニュアル、簡易説明書、またはPoulan 415324のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Poulan 415324の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Poulan 415324デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがPoulan 415324を使用するのを助ける技術的文書のことです。説明書は通常、全てのPoulan 415324ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Poulanの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Poulan 415324の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははPoulan 415324の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Poulan 415324に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Poulan 415324デバイスの基本機能を使うにあたってのヒント。 Poulan 415324のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Poulan 415324に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるPoulan 415324のメーカー/サービスへの連絡先に関する情報。

Poulan 415324についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもPoulan 415324の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPoulan 415324で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)