-
Pelco IDE - page 1
QUICK START C2961M (10/ 09) ID and IDE Series Network Fixed Dome Cameras Sarix ™ T echnology ...
-
Pelco IDE - page 2
2 C2961M (10/09) Product Overview Figure 1. Camera Connections an d Features ...
-
Pelco IDE - page 3
C2961M (10/09) 3 NOTES: • Pelco recommends co nnecting the ca mera to a network th at uses a Dynamic H ost Configuration Protocol (DHCP) ser ver to address device s. • Do not use a hub in the net work setup of the camera. • T o secure acce ss to the IP camer a, place the camer a behind a fire wall when it is conn ected to a network. ì Relay ...
-
Pelco IDE - page 4
4 C2961M (10/09) Installation BACK BOX AND LENS For detailed instructions, refer to the ID Series Installation/Operation m anual o r the IDE Series Installation/Operation manual. Bo th ar e available on th e resource disc. NOTE: Megapixel lenses are designed and tested to delive r optimal image quality to megapixel cameras. A standard definition le ...
-
Pelco IDE - page 5
C2961M (10/09) 5 3. Plug the network cable in to the RJ-45 network por t on the side of the back box. If the network has no PoE, connect a 24 V AC Class 2 power supply to the 24 V AC power connector . Figure 3. RJ-45 Pin Descriptio ns 4. Connect the necessary wiring for alarms and relays (refer to Figure 4). Only use the 24 V AC wires if PoE is not ...
-
Pelco IDE - page 6
6 C2961M (10/09) 5. Install the back box using one of the follow ing options: • In-Ceiling Instal lation (1) Install the back box by compre ssing t he spring clips and pushing the back box through the hole (refer to Figure 6 ). (2) T ighten the machine screws completely to secure the back box to the ceiling. Figure 6. In-Ceiling Insta llation • ...
-
Pelco IDE - page 7
C2961M (10/09) 7 7. Position the camera a. View the camera image using the service port or a Web browser . b. Unlock the tab locks located on each side of the camera. c. Manually rotate and tilt the camera module to position the camera. Do not over -rotate the module. d. Lock the tab locks to secure the camera. Figure 8. Positioning the Camera 8. F ...
-
Pelco IDE - page 8
8 C2961M (10/09) DOME LINER AND LOWER DOME 1. Align the magnets on the dome liner with the magnets located on the back box (refer to Figure 9). Figure 9. Installing the Dome Liner 2. Attach the lower dome leash to the back box (refer to Figure 10). Figure 10. Attaching the Leash ...
-
Pelco IDE - page 9
C2961M (10/09) 9 3. Move the lower dome latches away from the bubbl e until you hear a click. Align the lower dome latches with the slots located on the back box (refe r to Figure 11). Figure 11. Aligning the Lower Dome with the Ba ck Box 4. Snap the lower dome into place, and then move the lower dome latches towards the bubble until you hear a cli ...
-
Pelco IDE - page 10
10 C2961M (10/09) Operation Once the camera is installed, apply power to the camera. The camera will start a configuration sequence: the green LED flashes five times per second for approx imately two minutes, and then turns solid after the boot cycle is complete a nd the camera is on lin e. IP ADDRESS SETTINGS If the camera is connected to a Dynami ...
-
Pelco IDE - page 11
C2961M (10/09) 11 MINIMUM SYSTEM REQUIREMENTS ID SERIES Processor: Intel ® Pentium ® 4 microprocessor , 1.6 GHz Operating S ystem: Microsoft ® Win dows ® XP , Windows V ista ® , or Mac ® OS X 10.4 (or later) Memory: 512 MB RAM Network Interface Card : 100 megabits (or greater) Monitor: Minimum of 1024 x 768 r esolution, 16- or 32-bit pixel co ...
-
Pelco IDE - page 12
12 C2961M (10/09) LIVE PAGE ICONS Viewable icons are based on group permissions. Show Device List: Displays a list of viewable cameras connected to the same virtual lo cal area network (VLAN) as the camera to which you are logged on. Disable Viewer: Closes the live view window . 1 x 1 Mode: Displays a single video pane. 2 x 2 Mode: Displays 4 video ...
-
Pelco IDE - page 13
C2961M (10/09) 13 SETTINGS PAGE Depending on user permissions, t he Settings page allows you to manage camera system settings, set up users and groups, and control the camera. T o access the camera settings: 1. Log on to the camera. 2. Click the Settings link in the navigation bar located in the upper-right corner of the page; a list of menu tabs a ...
-
Pelco IDE - page 14
14 C2961M (10/09) A/V STREAMS T AB Use the A/V Streams tab to conf igure the video and audio streams for the camera. The A/V Streams tab includes a Video Presets page, a V ideo Configuration page, and an Audio Configuration page. Video Presets: The Video Preset p age includes three full y-configured video presets, which include primary and secondar ...
-
Pelco IDE - page 15
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merc handise proved defective in materi al or workma nship for a period of one year after the date of shipment. Exception s to this warrant y are as noted bel ow: • Five years: – Fiber optic products – TW3000 Series un shielded twiste d pair (UT ...
-
Pelco IDE - page 16
Pelco, Inc. W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el (800) 289-9100 Fax (800) 289-9150 International T el +1 (559) 292-1981 Fax +1 (559) 348-1120 www .pelco.co m ...
Pelco IDEについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもPelco IDEの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPelco IDEで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。