-
Delta 50-851 - page 1
INSTRUCTION MANUAL 2 H.P . Single-Stage Dust Collector (Model 50-851) P ART NO. 902114 - 07-01-02 Copyright © 2002 Delta Machinery T o learn more about DEL T A MACHINER Y visit our website at: www .deltamachinery .com. For Parts, Service, W arranty or other Assistance, please call 1-800-223-7278 ( In Canada call 1-800-463-3582). ...
-
Delta 50-851 - page 2
2 GENERAL SAFETY RULES W oodworking can be dangerous if safe and pr oper operating procedur es ar e not followed. As with all machinery , ther e are certain hazar ds involved with the operation of the pr oduct. Using the machine with respect and caution will considerably lessen the possibility of personal injury . However , if normal safety precaut ...
-
Delta 50-851 - page 3
3 ADDITIONAL SAFETY RULES FOR DUST COLLECTORS WARNING: F AILURE TO FOLLOW THESE RULES MA Y RESUL T IN SERIOUS PERSONAL INJUR Y . 1. DO NOT OPERA TE THIS MACHINE until it is assembled and installed according to the instructions. 2. OBT AIN ADVICE FROM YOUR SUPERVISOR, instructor , or another qualified person if you are not familiar with the operatio ...
-
Delta 50-851 - page 4
4 Fig. 2 Fig. 3 Fig. 2 1 - Blower and motor assembly 2 - Eight-hole rubber gasket 3 - T en-hole rubber gasket 4 - Base 5 - Intake Port Caps (3) 6 - Intake Ports 7 - Support Drum Fig. 3 8 - Filter bag 9 - Locking bands for filter and dust collection bags (2) 10 - Dust collection bag 11 - Support r od 12 - Support r od extension 13 - 5/16 - 18 x 5/8 ...
-
Delta 50-851 - page 5
5 Fig. 4 Fig. 5 Fig. 6 Fig. 7 ASSEMBLING CASTER ASSEMBLIES TO BASE 1. Align the holes in swivel caster assembly (A) Fig. 4, with four holes in caster bracket (B) located on the underside of base (C). Place a 5/16" lockwasher (E) Fig. 4 onto a 5/16-18x5/8" hex head screw (D), then place a 5/16" flat washer (F) onto the hex head screw ...
-
Delta 50-851 - page 6
6 Fig. 8 Fig. 9 Fig. 10 Fig. 11 5. Place ten-hole rubber gasket (J) Fig. 8, on blower flange (H). Align holes in gasket with mounting holes in blower flange and press gasket onto flange as shown. 6. Align mounting holes in chute (K) Fig. 9, with holes in gasket (J), which was assembled in STEP 5. Place a 5/16" lockwasher onto a 5/16-18x5/8&quo ...
-
Delta 50-851 - page 7
7 Fig. 12 Fig. 13 Fig. 14 Fig. 15 8. Align mounting holes in drum (N) Fig. 12, with gasket (M), which was assembled in STEP 7. Place a 5/16" lockwasher onto a 5/16-18x5/8" hex head screw , insert screw (P) Fig. 13 thr ough chute (K), thr ead screw into drum (N) and tighten securely . Repeat this process for the seven remaining holes. 9. A ...
-
Delta 50-851 - page 8
8 Fig. 16 Fig. 17 Fig. 18 Fig. 19 12. Assemble the other end of drum support arm (T) Fig. 16, to base (B). Place a 5/16" lockwasher onto a 5/16-18x5/8" hex head screw (W), insert the hex head screw thr ough drum support arm (T), and thr ead into base (B). Repeat this process for the r emaining hole. NOTE: Do not completely tighten mountin ...
-
Delta 50-851 - page 9
9 Fig. 20 Fig. 21 Fig. 22 Fig. 24 Fig. 23 3. Position open end of filter bag (A) Fig. 20, over upper lip of support drum (E). Insert locking band (F) Fig. 20, through the loops of filter bag (A) and fasten with clamp (G) a s shown in Fig. 21. NOTE: Make certain locking band (F) Fig. 20, is positioned in the channel of drum (E) before fastening clam ...
-
Delta 50-851 - page 10
10 Fig. 25 3. Three dust intake port caps (D) Fig. 25, are suppl ie d with the dust collector . NOTE: These caps should be inserted into the intake ports as shown, when they are not in use. WARNING: DO NOT INSER T FINGERS OR ANY FOREIGN OBJECT INTO THE DUST INT AKE PORTS WHEN UNIT IS OPERA TING. CONNECTING MACHINE TO POWER SOURCE ELECTRICAL CONNECT ...
-
Delta 50-851 - page 11
11 OPERA TING CONTROLS ON/OFF SWITCH The “on/off” switch is located on the side of the motor . T o tur n the dust collector “ON”, push the start button (A) Fig. 27. T o tur n the dust collector “OFF”, push stop button (B). Fig. 27 MAINTENANCE WARNING: Befor e any maintenance or service is performed, be sur e that the unit is disconnecte ...
-
Delta 50-851 - page 12
The following are trademarks of POR TER-CABLE · DEL T A (Las siguientes son marcas r egistradas de PORTER-CABLE S.A.): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’ s Saw ® , Contractor’ s Saw ® , Contractor’ s Saw II™, Delta ® , DEL T ACRAFT ® , DEL T AGRAM™, Delta Series 2000™, DURA TRONIC™, Emc²™, FLEX ® , Flying Chips? ...
Delta 50-851についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもDelta 50-851の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがDelta 50-851で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。