日本語 dropdown-ico

Toshiba SD-W1111の取扱説明書

34ページ 0.63 mb
ダウンロード

ページに移動 of 34

Summary
  • Toshiba SD-W1111 - page 1

    TOSHIBA DISK PRODUCTS DIVISION SD-W 1111 DVD-RAM DRIVE PRODUCT SPECIFICA TION JUNE 1999 REV . 1.0 Specifications are subject to change without notice DOCUMENT NUMBER 12043 ...

  • Toshiba SD-W1111 - page 2

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 2 Product Specification Matters to be attended to: This drive adopts RPC-II for its “ Standard Specification Model ” . This DVD-R A M Drive adopts RPC-II, the Phase II System of RPC (Regional Playback Control) for “ Standard Specification Model ” , on the basis of a ...

  • Toshiba SD-W1111 - page 3

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 3 Product Specification Precaution This equipment ( an optical disc drive) handled under the conditions out of product specifications may cause injury, heat generation, trouble, erroneous operation and performance degradation, so, care will be necessar y , and proper handlin ...

  • Toshiba SD-W1111 - page 4

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 4 Product Specification 1. Scope .................................................................................................................................................... 6 2. Features ............................................................................... ...

  • Toshiba SD-W1111 - page 5

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 5 Product Specification 15. MISCELLANEOUS ........................................................................................................................... 30 15.1 Accessories ......................................................................................... ...

  • Toshiba SD-W1111 - page 6

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 6 Product Specification 1. Scope The specification is applied to DVD-RAM drive SD-W1111. 2. Features (1) 2.6 GBytes capacity on one side of a 120 mm disc • Us ing 650 nm short-wavelength laser, 0.74 µ m single spiral land and groove tracking and Z-CLV system, realizes the ...

  • Toshiba SD-W1111 - page 7

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 7 Product Specification 3. External views and dimensions External views: 146.0 x 203.0 x 41.3 (mm) (W x D x H) (Except for f ront bezel) ...

  • Toshiba SD-W1111 - page 8

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 8 Product Specification 4. Basic specifications • 5.25 ” half height form factor • Applicable discs(1G B = 2 30 Byte, 1M B = 2 20 Byte 1K B = 2 10 Byte) 1) DVD-RAM * 1 DVD Specification s for R ewritable Disc Part 1 Ve rsion 1.0 2.42 GBytes* 2 x 1 ( C artridge with a s ...

  • Toshiba SD-W1111 - page 9

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 9 Product Specification • Average seek time ( Operating time of SEEK command ) DVD-RAM 120 ms ( typ.) DVD-ROM 210 ms ( typ.) CD-ROM 140 ms ( typ.) • Average access time DVD-RAM playback 180 ms * 1 ( typ.) DVD-ROM 260 ms * 1 ( typ.) CD-ROM 170 ms * 2 ( typ.) *1 Operation ...

  • Toshiba SD-W1111 - page 10

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 10 Product Specification 5. Power supply specifications 5.1 Input power supply +5V ± 5%, peak current 3A (Max. 2 sec., at spindle motor ON/OFF) Note: Power supply current is usually 1.4A. But at a spin-up time the current increase to 3.0A. If the power supply cable that is ...

  • Toshiba SD-W1111 - page 11

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 11 Product Specification According to the steps described below, the optical head auto-lock mechanism can be functioned. • Eject a disc. • Pull-in the tray inside the drive. • After “ BUSY ” lamp turns off, the auto-lock function completes. When transporting , tran ...

  • Toshiba SD-W1111 - page 12

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 12 Product Specification 8.2 Relative humidity Operating 8 to 80% RH Storing 5 to 95% RH Transporting (with packing) 5 to 95% RH (Temperature variation gradient: 10% /h, absolute humidity: 30 gm 3 ) * No dew condensation 8.3 Vibration(5 to 300 Hz) Operating 2 . 45 m/s 2 (0.2 ...

  • Toshiba SD-W1111 - page 13

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 13 Product Specification EN61000-4-6 : 1996 EN61000-4-8 : 199 3 EN61000-4-11 : 1994 ...

  • Toshiba SD-W1111 - page 14

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 14 Product Specification 9. Block diagram ROM (2 Mbit ) CPU DVD-RAM/ROM p rocessor LD c ontroller Mode select jumper Audio out I/F Authent ication Servo- a mp RF- a mp Pre- a m p Lens a ctuator Ho- LD Head SCSI controller CD-ROM d ecoder CD p rocessor S ervo p rocessor Actua ...

  • Toshiba SD-W1111 - page 15

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 15 Product Specification 10. Mounting 10.1 Mounting Mount the drive using four M3 tapping holes bottom and two M3 tapping holes on each side. The following shows an example mounting on a personal computer or a sub system. Use screws of which length inside the drive should be ...

  • Toshiba SD-W1111 - page 16

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 16 Product Specification 10.2 Mounting direction Install direction Horizontal or vertical installation (When using a n 80mm disc, vertical direction installation is not allowed.) Allowable slants (Refer to the drawing.) Left/right directions : Within ±15°. (When installing ...

  • Toshiba SD-W1111 - page 17

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 17 Product Specification 10.3 Notes on mounting • Keep more than 5mm clearance to circulate an adequate amount of air by c onvection around the drive and mounting metal parts. • Keep more than 0.8mm clearance around the top cover in order to secure absorbing shock and vi ...

  • Toshiba SD-W1111 - page 18

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 18 Product Specification • Do not apply force (under 1.5N : 150gf ) caving in the top plate. • Use screws of which length inside the drive should be more than 2.5mm and less than 3.5 mm from the drive frame surface . 2.5 - 3.5mm M3 screw Drive Frame ...

  • Toshiba SD-W1111 - page 19

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 19 Product Specification 11. Front bezel 11.1 Standard Bezel The front view of the drive with a s tandard bezel • Load/Unload switch: Push when ejecting/pulling-in the tray • Emergency disc eject hole: When ejecting a disc with power turned off, insert an exclusive tool ...

  • Toshiba SD-W1111 - page 20

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 20 Product Specification (3) A disc is not loaded, all LED ’ s turn off. (4) While executing following command, “ BUSY ” LED turns on. Command REASIGN READ WRITE SEEK WRITE & VERIFY VERIFY SEND DIAGONOSTIC READ HEADER SET READ AHEAD GET PERFORMANCE START / STOP UNI ...

  • Toshiba SD-W1111 - page 21

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 21 Product Specification 12. Rear View and Connectors The rear view of the drive • Power supply connector (4 pin): DC power supply is to be connected. • I / F (SCSI) connector (50 pin) : SCSI connector is to be connected. • Modes select h eaders (2 x 8 bits) : Used to ...

  • Toshiba SD-W1111 - page 22

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 22 Product Specification 12.2 I/F connector (SCSI connector) 12.2.1 Pin No. table of connector terminal Pin Signal Pin Signal 1 Ground 2 DB0 3 Ground 4 DB1 5 Ground 6 DB2 7 Ground 8 DB3 9 Ground 10 DB4 11 Ground 12 DB5 13 Ground 14 DB6 15 Ground 16 DB7 17 Ground 18 DBP 19 Gr ...

  • Toshiba SD-W1111 - page 23

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 23 Product Specification 12.2.2 External view diagram 12.2.3 Signal interface Type 50 core flat cable or 25 couple stranded wire cable Inductor size more than AWG28 Characteristic impedance 100 ohm ± 10% Maximum cable length 3.0m ...

  • Toshiba SD-W1111 - page 24

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 24 Product Specification 12.3 Mode select header s functions By inserting the jumper wire to the mode select headers , each kind of operation mode is made. Mode select headers : 2.54-mm pitch Pin No. Functions Setting at shipping 1 SCSI ID1 (LSB) Open 2 SCSI ID2 Open 3 SCSI ...

  • Toshiba SD-W1111 - page 25

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 25 Product Specification 1 2 3 4 12.3.4 ONE LUN/TWO LUN setting Pin 6 Function Open The drive operates in ONE LUN mode . Short The drive operates in TWO LUN mode . ONE LUN mode : The drive operates in one LUN (Logical Unit Number) for all discs to which SFF8090 Ver. 0.2 supp ...

  • Toshiba SD-W1111 - page 26

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 26 Product Specification 13. Host interface specification 13.1 Applicable standard SCSI Command set SFF8090 Ver. 2 Rev 0.95 ANSI X3T9.2 Rev 10 L 13.2 SCSI command set Code (Hex.) Command 00 TEST UNIT READY 01 REZERO UNIT 03 REQUEST SENSE 04 FORM A T UNIT 07 REASSIGN BLOCKS 1 ...

  • Toshiba SD-W1111 - page 27

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 27 Product Specification Code (Hex.) Command 5A MODE SEN S E (10) A2 SEND E VENT A3 SEND KEY A4 REPORT KEY A5 PL AY AUDIO (12) A7 SET READ AHEAD A8 READ (12) AA WRITE (12) AC GET PERFORMANCE AD READ DVD STRUCTURE AE WRITE AND VERIFY (12) AF VERIFY (12) B6 SET STREAMING B9 RE ...

  • Toshiba SD-W1111 - page 28

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 28 Product Specification 14. Notes on data guarantee 14.1 Disappearance of data in buffer in a write cache operation In a write cache operation, before data are actually written to a disc, a status response to the WRITE command or WRITE & VERIFY command is sent. If the p ...

  • Toshiba SD-W1111 - page 29

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 29 Product Specification Moreover, not only the data which tried to be recorded but also the data of other addresses in the same ECC block might be lost due to the failure to record. ...

  • Toshiba SD-W1111 - page 30

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 30 Product Specification 15. MISCELLANEOUS 15.1 Accessories Function setting jumper pins 5 p ie ce s. Emergency eject tool 1 p iece . 15.2 A bare disc setting at vertical installation In case of using a bare disc (ex. DVD-ROM or CD-ROM) at vertical installation, use disc hol ...

  • Toshiba SD-W1111 - page 31

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 31 Product Specification 3. First hang a disc on a disc holder in an upper and rear side of a tray , and then put the disc on disc holders in a down side of the tray. 4. Check three disc holders to confirm to the disc surely. ...

  • Toshiba SD-W1111 - page 32

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 32 Product Specification Notes in use (1) A disc might be scratched, damaged and dropped from a tray when used with a disc not correctly installed. Please install correctly and use a disc. (2) Please do drawing out (pulling return) a disc holder before setting a disc in a tr ...

  • Toshiba SD-W1111 - page 33

    OD- A 017 -0 2 TOSHIBA DVD-RAM SD-W1111 ‘ 99/0 6 / 26 Version 1 . 0 Page 33 Product Specification 15.3 Disc eject at emergency Please do according to the following procedures when it is necessary to take out a disc from the drive in the emergency. Check that the power supply of the drive is turned off and one minute or more passes. Insert an atta ...

  • Toshiba SD-W1111 - page 34

    Deviation List Page Item Rev # 0.9 a Rev # 1 . 0 3 Caution s --- Add (6) 8 Rotational speed(DVD-RAM) 1 ,130 - 2,640 rpm 1,028 – 2,400 rpm Host I/F ANSI ~ R ev 10k ANSI ~ Rev 10L 9 Average access time 150 ms ( typ.) 170 ms ( typ.) 12 8.3 vibration 9.8 cm/s 2 9.8 m/s 2 17 10.3 Notes on mounting 150 gf : 0.015N 1.5N : 150 gf 20 12 Rear V iew and Con ...

メーカー Toshiba カテゴリー DVD Recorder

Toshiba SD-W1111のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SD-W1111の取扱説明書
- Toshibaの製品カード
- パンフレット
- またはToshiba SD-W1111の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Toshiba SD-W1111の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Toshiba SD-W1111の取り付け説明書、サービスマニュアル、簡易説明書、またはToshiba SD-W1111のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Toshiba SD-W1111の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Toshiba SD-W1111デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがToshiba SD-W1111を使用するのを助ける技術的文書のことです。説明書は通常、全てのToshiba SD-W1111ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Toshibaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Toshiba SD-W1111の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははToshiba SD-W1111の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Toshiba SD-W1111に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Toshiba SD-W1111デバイスの基本機能を使うにあたってのヒント。 Toshiba SD-W1111のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Toshiba SD-W1111に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるToshiba SD-W1111のメーカー/サービスへの連絡先に関する情報。

Toshiba SD-W1111についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもToshiba SD-W1111の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがToshiba SD-W1111で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)