Mitsubishi Electronics WD8700Uの取扱説明書

19ページ 1.43 mb
ダウンロード

ページに移動 of 19

Summary
  • Mitsubishi Electronics WD8700U - page 1

    1 DLP™ Pr ojector WD8700U Contr olling the pr ojector via RS-232C connection Contents 1. Introduction ............................................................................................................ 2 1.1 Connection ........................................................................................................................ ...

  • Mitsubishi Electronics WD8700U - page 2

    2 1 . Introduct ion This projector can be contr olled by connecting a personal computer with RS-232C terminal. In addition, by connecting multiple projectors to each other in a daisy chain configuration, you can contr ol each projector fr om one personal computer . PC-controllable functions: • T urning the power ON or OFF • Changing input sign ...

  • Mitsubishi Electronics WD8700U - page 3

    3 • Example of ID setting (When Group A, which performs multi-pr ojection with two projectors, and Group B, which performs multi-projection with thr ee projectors, are connected.) Projector 1 PROJECTOR ID : 01 GROUP ID : A Multi-projection Gr oup A Projector 2 PROJECTOR ID : 02 GROUP ID : A Projector 3 PROJECTOR ID : 03 GROUP ID : B Multi-project ...

  • Mitsubishi Electronics WD8700U - page 4

    4 2 . Cont rol com man d config ur ati on The command consists of the address code, ID code, function code, data code, ACK/NAK, and end code. The length of the command varies among the functions. Address code ID code Function code Data code ACK/NAK End code ASCII code ‘30h’ ‘30h’ ‘3Bh’ ID ‘3Bh’ Function Data ‘3Ah’ ‘4Eh’ ‘ ...

  • Mitsubishi Electronics WD8700U - page 5

    5 • The projector may not r eceive a command when the splash screen is being displayed immediately after turning on the power . Use command “00r10” to cancel the splash screen. • While using the LAN terminals, the LAN functions take precedence. • For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number ...

  • Mitsubishi Electronics WD8700U - page 6

    6 Projector error Send out “00vER” to check error details. Recover from error state. 0– 3 To normal operation 4 Enter password. Send out “00PASS****.” Projector is functioning. Use “00FNCOFF” to cancel the current function. 65 Sending “00vST” Checking response to “00vST” [Method of checking state of projector] Sending out comm ...

  • Mitsubishi Electronics WD8700U - page 7

    7 4. Execut io n proc edu re of RS -232 C comma nd s via L A N • When you use the LAN function, set the ST ANDBY MODE to ST ANDARD or LAN. • When you execute RS-232C commands via LAN, check that the CONTROL SYSTEM in the NETWORK menu is set to ST ANDARD. • Y ou can change the certification password using the NETWORK P ASSWORD in the NETWORK ...

  • Mitsubishi Electronics WD8700U - page 8

    8 5. Comma nd lis t 5. 1 Gen er al co nt rol c omm an ds The general control commands are used for the basic operation setting of this projector . They may not be exe- cuted while the signals are changed. The general control commands have no data codes. (When the commands for input select are sent while the splash screen is being displayed, the spl ...

  • Mitsubishi Electronics WD8700U - page 9

    9 5. 2 . 2 Read co mma nd s for i tem s in IN FORMA TION me nu Use the following commands to obtain the values of the items in the INFORMA TION menu. ITEM Function Data (Receive) Character ASCII code LAMP 1 TIME (LOW) vLE1L 76h 4Ch 45h 31h 4Ch hhhhmm LAMP 2 TIME (LOW) vLE2L 76h 4Ch 45h 32h 4Ch hhhhmm LAMP illuminating status (an icon displayed at t ...

  • Mitsubishi Electronics WD8700U - page 10

    10 [Example] When checking the currently selected input terminal (when the INPUT VIDEO is being selected). (V alues enclosed in quotation marks are ASCII codes.): • When ID is not specied: Command sent from the PC, etc. Status code returned from the pr ojector Description ‘30’ ‘30’ ‘76’ ‘49’ ‘0D’ 00vl Command for checking t ...

  • Mitsubishi Electronics WD8700U - page 11

    11 [Example] When displaying the MENU selection bar . (V alues enclosed in quotation marks are ASCII codes.): • When ID is not specied: Command sent from the PC, etc. Status code returned from the pr ojector Description ‘30’ ‘30’ ‘72’ ‘35’ ‘34’ ‘0D’ 00r54 Command operating the same as the MENU button (ID command is omit ...

  • Mitsubishi Electronics WD8700U - page 12

    12 5. 5 Funct ion c omma nd s (Not executable in stand-by m ode. When the mute comman ds are sent while the spl ash screen is being displayed, the splash screen is only canceled.) ITEM Function Data Character ASCII code BLANK MUTE 4Dh 55h 54h 45h 0 (OFF), 1 (ON) SPLIT SPL T 53h 50h 4Ch 54h 0 (OFF), 1 (ON) MAGNIFY MGNFY 4Dh 47h 4Eh 46h 59h 0 (OFF), ...

  • Mitsubishi Electronics WD8700U - page 13

    13 ITEM Function Data Character ASCII code NOISE REDUCTION NR 4Eh 52h 0 (OFF), 1 (ON) CTI CTI 43h 54h 49h 0 (OFF), 1 (ON) INPUT LEVEL IPL 49h 50h 4Ch ±5, For DVI input: +0 (NORMAL), +1 (ENHANCED) For HDMI input: +0 (AUTO), +1 (NORMAL), +2 (ENHANCED) CLOSED CAPTION CC 43h 43h 0 (OFF), 1 (CC1), 2 (CC2) DEMO MODE DM 44h 4Dh 0 (OFF), 1 (ALL), 2 (DYNAM ...

  • Mitsubishi Electronics WD8700U - page 14

    14 ITEM Function Data Character ASCII code REMOTE 1 MODE (RESET) R1MRST 52h 31h 4Dh 52h 53h 54h FIL TER MENU (CLEANUP PERIOD) FLCP 46h 4Ch 43h 50h xdhh x: Cleanup interval 0 (OFF), 1 (24H), 2 (1WEEK) dhh: Next cleanup time (d: days, hh: hours) OFF: Fixed to 0 days and 00 hours 24H: Max. 0 days and 24 hours 1 WEEK: Max. 7 days and 00 hours FIL TER M ...

  • Mitsubishi Electronics WD8700U - page 15

    15 ITEM Function Data Character ASCII code COLOR MA TCHING- MANUAL (RESET) MNRST 4Dh 4Eh 52h 53h 54h COLOR MA TCHING- -MEASURE-MEASURED DA T A (Y(Relative value)) MSML 4Dh 53h 4Dh 4Ch x00050 to 20000 x: Color selection R (RED), G (GREEN), B (BLUE), W (WHITE) COLOR MA TCHING- -MEASURE-MEASURED DA T A (x) MSMX 4Dh 53h 4Dh 58h x*.*** to *.*** x: Color ...

  • Mitsubishi Electronics WD8700U - page 16

    16 5.6 .6 SIG NA L men u ITEM Function Data Character ASCII code MEMOR Y CALL MMC 4Dh 4Dh 43h 0 (AUTO), 1 to 8 (MEMOR Y 1 to 8) HORIZ.POSITION HP 48h 50h + (increment), - (decrement) *1 VERT . POSITION VP 56h 50h + (incr ement), - (decrement) *1 FINE SYNC. FN 46h 4Eh 00–31 TRACKING TRK 54h 52h 4Bh + (increment), - (decr ement) *1 COMPUTER INPUT C ...

  • Mitsubishi Electronics WD8700U - page 17

    17 How to set the value Use the character or ASCII code as shown below to set the value. Character + - 0 1 2 3 4 5 6 7 8 9 ASCII code ‘2Bh’ ‘2Dh’ ‘30h’ ‘31h’ ‘32h’ ‘33h’ ‘34h’ ‘35h’ ‘36h’ ‘37h’ ‘38h’ ‘39h’ [Example 1] When setting the AUTO POWER ON to ON. (V alues enclosed in quotation marks are ASCII ...

  • Mitsubishi Electronics WD8700U - page 18

    18 [Example 3] When checking the TINT setting (when the TINT is set to +10). (V alues enclosed in quotation marks are ASCII codes.): • When ID is not specied: Command sent from the PC, etc. Status code returned from the pr ojector Description ‘30’ ‘30’ ‘53’ ‘0D’ 00S Command for checking the TINT setting (ID command is omitted.) ...

  • Mitsubishi Electronics WD8700U - page 19

    19 5.7 Passwor d loc k com man ds The password lock commands control the password lock. The password lock enabling or disabling command is sent with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password lock is enabled or disabled successfully , the projector sends a return command comprising ...

メーカー Mitsubishi Electronics カテゴリー Projector

Mitsubishi Electronics WD8700Uのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WD8700Uの取扱説明書
- Mitsubishi Electronicsの製品カード
- パンフレット
- またはMitsubishi Electronics WD8700Uの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Mitsubishi Electronics WD8700Uの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Mitsubishi Electronics WD8700Uの取り付け説明書、サービスマニュアル、簡易説明書、またはMitsubishi Electronics WD8700Uのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Mitsubishi Electronics WD8700Uの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Mitsubishi Electronics WD8700Uデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMitsubishi Electronics WD8700Uを使用するのを助ける技術的文書のことです。説明書は通常、全てのMitsubishi Electronics WD8700Uユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Mitsubishi Electronicsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Mitsubishi Electronics WD8700Uの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMitsubishi Electronics WD8700Uの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Mitsubishi Electronics WD8700Uに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Mitsubishi Electronics WD8700Uデバイスの基本機能を使うにあたってのヒント。 Mitsubishi Electronics WD8700Uのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Mitsubishi Electronics WD8700Uに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMitsubishi Electronics WD8700Uのメーカー/サービスへの連絡先に関する情報。

Mitsubishi Electronics WD8700Uについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMitsubishi Electronics WD8700Uの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMitsubishi Electronics WD8700Uで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)