Husqvarna CTH2036Tの取扱説明書

32ページ 1.6 mb
ダウンロード

ページに移動 of 32

Summary
  • Husqvarna CTH2036T - page 1

    CTH2036T  Operator's Manual ...

  • Husqvarna CTH2036T - page 2

    2 I. GENERAL OPERA TION • Read, understand, and follow all instructions on the machine and in the manual before starting. • Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times. • Only allow responsible adults, who are familiar with the in struc tions, to operate the machine. • ...

  • Husqvarna CTH2036T - page 3

    3 • Be sure the area is clear of bystanders before operat- ing. Stop machine if anyone enters the area. • Never carry passengers. • Do not mow in reverse unless absolutely necessary . Al ways look down and behind before and while back- ing. • Never carry children, even with the blades shut off. They may fall off and be seriously injured or ...

  • Husqvarna CTH2036T - page 4

    4 CONGRA TUL A TIONS on your purchase of a new tractor . It has been designed, engineered and manu fac tured to give you the best possible dependability and per for mance. Should you experience any problem you cannot easily remedy , please contact your nearest authorized service center . We have competent, well-trained tech ni cians and the proper ...

  • Husqvarna CTH2036T - page 5

    5 UNAS SEMBLED P ARTS Steering Wheel (1) W asher (1) Knob Steering Wheel Inser t Seat (1) Seat Steering Wheel Adapter Keys (2) K eys Slope Sheet (1) Oil Drain T ube F or Future Use (1) Large Flat W asher (1) Lockn ut ...

  • Husqvarna CTH2036T - page 6

    6 AS SEMBL Y BEFORE REMOVING TRAC TOR FROM SKID Fig. 1 4100 STEERING WHEEL INSERT L OCK NUT L ARGE FLAT WASHER STEERING WHEEL STEERING SHAFT STEERING SLEEVE STEERING WHEEL ADAPTOR Y our new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. T o ensure safe and proper operation of your tra ...

  • Husqvarna CTH2036T - page 7

    7 AS SEMBL Y Fig. 3 2 4 6 6 02464 SEA T P AN SHOULDER BOL T ADJUSTMENT KNOB FL A T WASHER SEA T NOTE: Y ou may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid. WARNING: Before start ing, read, un der stand and fol low all in struc tions in the Op er a tion section of this man u al. Be sure tract ...

  • Husqvarna CTH2036T - page 8

    8 AS SEMBL Y 02306 HOOK BACKPL A TE SL OT DISCHARGE CHUTE Fig. 6 Fig. 7 CLEVIS PIN 3/8 X 11/16 CLEVIS PIN 3/8 X 2 SUPPORT BRACKET 13/32 FL A T WASHER RET AINER SPRING 02813 SUPPORT BRACKET Fig. 8 Fig. 10 TO ASSEMBLE BAGGER (See Figs. 8-10) • Unfold bag by pivoting front bagger tube all the way forward and pressing the bottom vinyl binding onto th ...

  • Husqvarna CTH2036T - page 9

    9 AS SEMBL Y 0 2 2 1 4 A A HAN DLE PIN RE T AIN ER SPRING PLUG Fig. 11 Fig. 12 TO ASSEMBLE AND INST ALL MULCHER PLUG (See Fig. 12) • Remove spring retainer and pin from handle. • Insert plug into handle. Make sure that the letter "A" on both the plug and handle are on the same side and that they can both be seen from the top when layi ...

  • Husqvarna CTH2036T - page 10

    10 OPERA TION These symbols may appear on your tractor or in literature supplied with the product. Learn and understand their meaning. DANGER, KEEP HANDS AND FEET AWAY FREE WHEEL (Automatic Models only) OVER TEMP LIGHT KEEP AREA CLEAR SLOPE HAZARDS 15 15 (SEE SAFETY RULES SECTION) BATTERY REVERSE FORWARD FAST SLOW ENGINE ON ENGINE OFF OIL PRESSURE ...

  • Husqvarna CTH2036T - page 11

    11 OPERA TION KNOW YOUR TRACTOR READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERA TING YOUR TRACTOR Compare the illustrations with your tractor to familiarize yourself with the locations of various controls and ad just ments. Save this manual for future reference. Our tractors conform to the applicable safety standards of the American Nat ...

  • Husqvarna CTH2036T - page 12

    12 OPERA TION The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye dam age. Always wear safety glass es or eye shields while operating your tractor or per form ing any adjustments or repairs. We rec om mend a wide vision safety mask over spectacles or stan dard safety glasses. HOW TO USE YO ...

  • Husqvarna CTH2036T - page 13

    13 OPERA TION Fig. 16 Fig. 15 02710 AT T ACH MENT CLUTCH SWITCH "DISENGAGED" PO SI TION AT T ACH MENT LIFT LEVER HIGH PO SI TION "EN GAGED" PO SI TION LO W POSITION TO OPERA TE MOWER (See Fig. 16) Y our tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine run ...

  • Husqvarna CTH2036T - page 14

    14 Fig. 18 TOWING CARTS AND OTHER A T T ACH MENTS T ow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor . Use common sense when towing. T oo heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor . TO TRAN ...

  • Husqvarna CTH2036T - page 15

    15 Fig. 19 OPERA TION NOTE: Before starting, read the warm and cold starting procedures below . • Insert key into ignition and turn key clockwise to “ST ART” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen sec onds per minute. If the engine does not start after several attempts, push ch ...

  • Husqvarna CTH2036T - page 16

    16 OPERA TION • If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip pings. Make first cut relatively high; the second to the desired height. • Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing. • Always operate engi ...

  • Husqvarna CTH2036T - page 17

    17 MAINTENANCE LUBRICA TION CHART T R A C T 0 R Inspect Muffler/Spark Arrester Clean Air Filter Change Engine Oil (with oil filter) Replace Air Filter Paper Cartridge Replace Spark Plug Check Engine Oil Level Clean Engine Cooling Fins Clean Air Screen 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Servi ...

  • Husqvarna CTH2036T - page 18

    18 MAINTENANCE TRACTOR Always observe safety rules when per form ing any main te nance. BRAKE OPERA TION If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be checked and ad just ed. (See “TO CHECK BRAKE” in the Ser vice and Ad just ments section of th ...

  • Husqvarna CTH2036T - page 19

    19 MAINTENANCE BA TTERY Y our tractor has a battery charging system which is suf fi cient for normal use. However , periodic charging of the battery with an automotive charger will extend its life. • Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour . NOTE: The ...

  • Husqvarna CTH2036T - page 20

    20 MAINTENANCE TO CHANGE ENGINE OIL (See Fig. 27) Determine temperature range expected before oil change. All oil must meet API service classification SG-SL. • Be sure tractor is on level surface. • Oil will drain more freely when warm. • Catch oil in a suitable container . • Remove oil fill cap/dipstick. Be careful not to allow dirt to ent ...

  • Husqvarna CTH2036T - page 21

    21 SERVICE AND ADJUSTMENTS Fig. 28 WARNING: TO A VOID SE RI OUS IN JU RY , BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS: • Depress brake pedal fully and set parking brake. • Place motion control lever in neutral position. • Place attachment clutch in “DISENGAGED” position. • T urn ignition key to “STOP” and remove key . • Make sur ...

  • Husqvarna CTH2036T - page 22

    22 SERVICE AND ADJUSTMENTS 01268 "D" "D" MANDREL Fig. 31 Fig. 32 • When distance “D” is 1/8" to 1/2" lower at front than rear , tighten nuts “F” against trunnion on both front links. • T o raise front of mower , loosen nut “F ” from trunnion on both front links. Tighten nut “E” on both front links a ...

  • Husqvarna CTH2036T - page 23

    23 SERVICE AND ADJUSTMENTS Fig. 34 LH MANDREL COVER IDLER PULLEY BEL T MANDREL PULLEY IDLER PULLEY RH MANDREL COVER MANDRELL PULLEY TO CHECK BRAKE If tractor requires more than five (5) feet to stop at highest speed in high est gear on a level, dry concrete or paved surface, then brake must be serviced. Y ou may also check brake by: 1. P ark tracto ...

  • Husqvarna CTH2036T - page 24

    24 SERVICE AND ADJUSTMENTS TO REMOVE WHEEL FOR REP AIRS (See Fig. 38) • Block up axle securely . • Remove axle cover , retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose). • Repair tire and reassemble. • On rear wheels only: align grooves in rear wheel hub and axle. Insert square key . • Repl ...

  • Husqvarna CTH2036T - page 25

    25 SERVICE AND ADJUSTMENTS TO REMOVE HOOD AND GRILL ASSEMBL Y (See Fig. 41) • Raise hood. • Unsnap headlight wire connector . • Stand in front of tractor . Grasp hood at sides, tilt toward engine and lift off of tractor . • T o replace, reverse above procedure. Fig. 41 02778 HOOD HEADLIGHT WIRE CONNECTOR TO REPL ACE HEADLIGHT BULB • Raise ...

  • Husqvarna CTH2036T - page 26

    26 STORAGE Immediately prepare your tractor for storage at the end of the season or if the tractor will not be used for 30 days or more. WARNING: Never store the trac tor with gas o line in the tank inside a building where fumes may reach an open flame or spark. Allow the engine to cool before storing in any en clo sure. TRACTOR Remove mower from t ...

  • Husqvarna CTH2036T - page 27

    27 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Will not start 1. Out of fuel. 1. Fill fuel tank. 2. Engine not “CHOKED” properly . 2. See “TO ST ART ENGINE” in Operation section. 3. Engine flooded. 3. Wait several minutes before attempting to start. 4. Bad spark plug. 4. Replace spark plug. 5. Dirty air filter . 5. Clean/replace air fil ...

  • Husqvarna CTH2036T - page 28

    28 TROUBLESHOOTING POINTS PROBLEM CAUSE CORRECTION Engine continues to run when oper- ator leaves seat with attachment clutch engaged 1. F aulty operator -safety presence control system. 1. Check wiring, switches and connections. If not corrected, contact an authorized service center/ department. Poor cut - uneven 1. Worn, bent or loose blade. 1. R ...

  • Husqvarna CTH2036T - page 29

    29 15 DEGREES MAX. FOLD ALONG DOTTED LINE THIS IS A 15 DEGREE SLOPE ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION WARNING: To avoid serious injury, operate your tractor up and down the face of slopes, never across the face. Do not mow slopes greater than 15 degrees. Make turns gradually to preven ...

  • Husqvarna CTH2036T - page 30

    30 SERVICE NOTES ...

  • Husqvarna CTH2036T - page 31

    31 SERVICE NOTES ...

  • Husqvarna CTH2036T - page 32

    532 42 66-43 04.01.09 CL Printed in the U.S.A. ...

メーカー Husqvarna カテゴリー Lawn Mower

Husqvarna CTH2036Tのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CTH2036Tの取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna CTH2036Tの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna CTH2036Tの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna CTH2036Tの取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna CTH2036Tのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna CTH2036Tの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna CTH2036Tデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna CTH2036Tを使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna CTH2036Tユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna CTH2036Tの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna CTH2036Tの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna CTH2036Tに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna CTH2036Tデバイスの基本機能を使うにあたってのヒント。 Husqvarna CTH2036Tのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna CTH2036Tに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna CTH2036Tのメーカー/サービスへの連絡先に関する情報。

Husqvarna CTH2036Tについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna CTH2036Tの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna CTH2036Tで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)