-
Peerless Industries 3P600 - page 1
© Copyright 2000 Pr inted Great Plains Mfg., Inc. Used with: Installation Instructions 151-071M 6 Foot Drill Seed Box Agitator Option • 605NT • 3P605NT • 3P600 General Inf ormation Assembl y Instructions When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of other ...
-
Peerless Industries 3P600 - page 2
151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Bo x Agitator Option 2 5. Slide lock collars (8 and 10) against bearing and flanges (7 and 11) and tighten set screws . See Figure 2 Agitator shaft Installation 18727 Figure 2: 2. Slide agitator shaft (5) into seed bo x from left side of drill. 3. As shaft adv ances , slide on par ts in the f ol- low ...
-
Peerless Industries 3P600 - page 3
3/31/2004 151-071M Great Plains Mfg., Inc. 3 Installation Instructions Drive Assembl y 605NT and 3P605NT Drive NO TE: If your drill is equipped with a native g rass option, a majority of the agitator dr iv e is already installed. Go to page 4 f or chain routing. See Figure 3 605NT & 3P605NT Drive Assembly 18662 Figure 3: 1. Mount bearings and ? ...
-
Peerless Industries 3P600 - page 4
151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Bo x Agitator Option 4 5. Ref er to Figure 4 . Figure 4 Gearbo x Sproc ket 18728 Install 16 tooth splined sprock et (11) to gearbo x as shown, and fas- ten with snap ring (12). See Figure 5 18730 Agitator Chain Routing with Native Grass Agitator Chain Routing NO TE: F or dr ills with the nativ e grass ...
-
Peerless Industries 3P600 - page 5
3/31/2004 151-071M Great Plains Mfg., Inc. 5 Installation Instructions 3P600 Drive See Figure 6 3P600 Drive Assembly 18728 Figure 6: 1. Mount bearing and flanges (1) inside end panels of drill frame. Use 5/16 x 1 inch bolts (2), washers and n uts to secure flanges . Leav e bolts loose. 2. Install drive shaft (3) through bearings. As y ou install ...
-
Peerless Industries 3P600 - page 6
151-071M 3/31/2004 Great Plains Mfg., Inc. Seed Bo x Agitator Option 6 See Figure 7 Idler Installation 18731 Figure 7: 6. Install two 12 tooth idler sproc k ets (10) in lo- cations shown, using 1/2 x 3 1/2 inch bolts (11), he x jam nuts (12), USS flat w ashers (13) and he x flange n uts (14). See Figure 8 3P600 Chain Routing 18732 Figure 8: 7. Ro ...
-
Peerless Industries 3P600 - page 7
3/31/2004 151-071M Great Plains Mfg., Inc. 7 Installation Instructions Agitator P ad dle Installation See Figure 9 Agitator P addle Assembl y 18739 paddle 1 paddle 2 paddle 3 paddle 4 paddle 5 paddle 6 Figure 9: 1. Place an agitator paddle (1) ov er the he x shaft directly abov e a f eeder cup. P osition paddle as shown (paddle 1). 2. Slip a 1/4 x ...
-
Peerless Industries 3P600 - page 8
3/31/2004 151-071M Great Plains Mfg., Inc. Seed Bo x Agitator Option 8 118-748A 3P600 A GIT A T OR ASSY W/DRIVE - 7-1/2" Y our kit includes: 9 118-493D A GIT A TOR P ADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOA T DO WN FLOA T ST OP 1 118-556D 6’ DRILL A GIT A TOR SHAFT 1 133-037D SGS/A UXILLAR Y DRIVE SHAFT 1 136-06 ...
-
Peerless Industries 3P600 - page 9
151-071M 3/31/2004 Great Plains Mfg., Inc. 9 Installation Instructions 118-750A 605NT & 3P605NT A GIT A T OR ASSY W/DRIVE Y our kit includes: 9 118-493D A GIT A TOR P ADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOA T DO WN FLOA T ST OP 1 118-556D 6’ DRILL A GIT A TOR SHAFT 1 202-182D A UXILLAR Y DRIVE SHAFT 1 136-054D C ...
-
Peerless Industries 3P600 - page 10
3/31/2004 151-071M Great Plains Mfg., Inc. Seed Bo x Agitator Option 10 118-751A 605NT & 3P605NT A GIT A T OR ASSY WITHOUT DRIVE Y our kit includes: 9 118-493D A GIT A TOR P ADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOA T DO WN FLOA T ST OP 1 118-556D 6’ DRILL A GIT A TOR SHAFT 1 136-054D CHAIN RL #40 89 PITCHES 1 168 ...
-
Peerless Industries 3P600 - page 11
151-071M 3/31/2004 Great Plains Mfg., Inc. 11 Installation Instructions 118-788A 3P600 A GIT A T OR ASSY W/DRIVE - 6" Y our kit includes: 11 118-493D A GIT A TOR P ADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOA T DO WN FLOA T ST OP 1 118-556D 6’ DRILL ADGIT A TOR SHAFT 1 133-037D SGS/A UXILLAR Y DRIVE SHAFT 1 136-104D ...
-
Peerless Industries 3P600 - page 12
3/31/2004 151-071M Great Plains Mfg., Inc. Seed Bo x Agitator Option 12 118-789A 3P600 A GIT A T OR ASSY WITHOUT DRIVE - 6" Y our kit includes: 11 118-493D A GIT A TOR P ADDLE 3/4 HEX 2 118-494D LOCK COLLAR 3/4 HEX BORE 1 118-498D SEED FLOA T DO WN FLOA T ST OP 1 118-556D 6’ DRILL A GIT A TOR SHAFT 1 136-111D CHAIN RL #40 68 PITCHES 1 168-12 ...
Peerless Industries 3P600についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもPeerless Industries 3P600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPeerless Industries 3P600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。