Ryobi DP120の取扱説明書

18ページ 0.88 mb
ダウンロード

ページに移動 of 18

Summary
  • Ryobi DP120 - page 1

    1 THANK YOU FOR BUYING A RYOBI BENCHT OP DRILL PRESS. Y our new Drill Press has been engineered and manufactured to Ryobi's high standards for dependability , ease of operation, and operator safety . Properly cared for , it will give you years of rugged, trouble-free performance. CAUTION : Carefully read through this entire operator's man ...

  • Ryobi DP120 - page 2

    2 Chuck 1/2 in. (13 mm) No Load Speed 280 - 3000 RPM Swing 12 in. (305 mm) Spindle T ravel 3-1/4 in. (82 mm) Input 120V AC, 60Hz, 5 amps Net Weight 84 lbs (38 kg) Look for this symbol to point out important safety precautions. It means attention!!! Y our safety is involved. W ARNING: T ABLE OF CONTENTS PRODUCT SPECIFICA TIONS ■ Product Specificat ...

  • Ryobi DP120 - page 3

    3 RULES FOR SAFE OPERA TION Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Safety is a combination of common sense, staying alert, and knowing how your tool works. READ ALL INSTRUCTIONS ■ KNOW YOUR POWER T OOL. Safe operation of this power tool requires that ...

  • Ryobi DP120 - page 4

    4 ■ AL W A YS TURN SWITCH OFF before disconnecting it to avoid accidental starting. ■ ALL REP AIRS, WHETHER ELECTRICAL OR MECHANICAL , should be made at a Ryobi Authorized Service Center . Use only Ryobi identical replacement parts. ■ SA VE THESE INSTRUCTIONS. Refer to them frequently and use to instruct other users. If you loan someone this ...

  • Ryobi DP120 - page 5

    5 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper acciden ...

  • Ryobi DP120 - page 6

    6 ELECTRICAL EXTENSION CORDS Use only 3-wire extension cords that have 3-prong ground- ing plugs and 3-pole receptacles that accept the tool's plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a ...

  • Ryobi DP120 - page 7

    7 GLOSSAR Y OF TERMS Feed Handles Three handles attached to the quill which allow the operator to lower the chuck and bit during a drilling operation. Motor Pulley A grooved, conical pulley driven by the motor and responsible for driving the spindle pulley by means of a belt. Pilot Hole A small hole drilled in a workpiece that serves as a guide for ...

  • Ryobi DP120 - page 8

    8 Fig. 2 ■ Spindle ■ Chuck T ool ■ Chuck Key ■ Chuck ■ Housing Knob and Screw ■ Hex Bolts, M10 x 25 (4) ■ Hex Wrench ■ T able Adjustment Handle ■ Operator ’ s Manual (not shown) Check all loose parts with the list below . Assemble according to the instructions on the following pages. 1 2 D r l l i P r e s s ON R E M O V E T O L ...

  • Ryobi DP120 - page 9

    9 FEA TURES Fig. 3 KNOW YOUR DRILL PRESS See Figure 3. Before attempting to use your drill press, familiarize your- self with all the operating and safety requirements. BEL T TENSION LEVER The belt tension lever is used to release or tighten belt tension. BEL T TENSION SCREWS Belt tension screws on each side of the pulley housing lock the belt tens ...

  • Ryobi DP120 - page 10

    10 ASSEMBL Y W ARNING: Do not connect to power supply until assembly is complete. Failure to comply could result in accidental starting and possible serious injury . AT T ACHING THE COLUMN ASSEMBL Y See Figure 4. ■ Place base on a flat surface. Align screw holes in the column support with screw holes in the base. ■ Place a hex bolt in each hole ...

  • Ryobi DP120 - page 11

    11 ASSEMBL Y INST ALLING THE IDLER PULLEY See Figures 7 and 8. ■ Place idler pulley in the center hole in the head assembly . Fit one belt over the spindle pulley and the idler pulley and the other belt over the motor pulley and the idler pulley . T ighten the belt tension lever and the two belt tension screws. See Figure 7. ■ Fit the spindle i ...

  • Ryobi DP120 - page 12

    12 ADJUSTMENTS Fig. 11 T ABLE ADJUSTMENT HANDLE T ABLE LOCK HANDLE 0 0 10 20 30 40 10 20 30 40 1 2 D r l l i P r e s s O N W ARNING: Before performing any adjustment, make sure the drill press is unplugged from the power supply and the switch is in the OFF position. Failure to heed this warning could result in serious personal injury . ADJUSTING TA ...

  • Ryobi DP120 - page 13

    13 1 2 D r l l i P r e s s O N R E M O V E T O L O C K ADJUSTMENTS Fig. 14 BEL T TENSION LEVER CHANGING SPEEDS See Figure 14. W ARNING: Before performing any adjustment, make sure the drill press is unplugged from the power supply and the switch is in the OFF position. Failure to heed this warning could result in serious personal injury . The spind ...

  • Ryobi DP120 - page 14

    14 INST ALLING BITS See Figure 16. ■ Unplug your drill press. ■ Open or close the chuck jaws to a point where the opening is slightly larger than the drill bit you intend to use. ■ Insert drill bit into chuck the full length of the jaws. W ARNING: Do not insert drill bit into chuck jaws and tighten as shown in figure 16. This could cause dril ...

  • Ryobi DP120 - page 15

    15 W ARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. W ARNING: To avoid serious personal injury make sure the drill press is turned OFF and the cord is unplugged from the power source before performing any maintenance or adjustment. GENERAL MAINTENANCE After usin ...

  • Ryobi DP120 - page 16

    16 Problem Possible Cause Solution Noisy operation Bit burns or smokes Excessive drill runout or wobble Drill bit binds in workpiece W orkpiece support loosens Adjust belt tension. Lubricate spindle. T ighten set screws in pulleys. Change speed. Retract bit frequently to clear chips. Sharpen or replace bit. Feed fast enough, allow drill to cut. Lub ...

  • Ryobi DP120 - page 17

    17 NOTES NOTES ...

  • Ryobi DP120 - page 18

    983000-040 12-02 RYOBI TECHNOLOGIES, INC. 1428 Pearman Dairy Road Anderson, SC 29625 Post Office Box 1207 Anderson SC 29622-1207 Phone 1-800-525-2579 www.ryobitools.com OPERA T OR'S MANUAL 12 in. (305 mm) Drill Press Model DP120 • SER VICE Now that you have purchased your tool, should a need ever exist for repair parts or service, simply con ...

メーカー Ryobi カテゴリー Drill

Ryobi DP120のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DP120の取扱説明書
- Ryobiの製品カード
- パンフレット
- またはRyobi DP120の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Ryobi DP120の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Ryobi DP120の取り付け説明書、サービスマニュアル、簡易説明書、またはRyobi DP120のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Ryobi DP120の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Ryobi DP120デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRyobi DP120を使用するのを助ける技術的文書のことです。説明書は通常、全てのRyobi DP120ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Ryobiの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Ryobi DP120の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRyobi DP120の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Ryobi DP120に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Ryobi DP120デバイスの基本機能を使うにあたってのヒント。 Ryobi DP120のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Ryobi DP120に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRyobi DP120のメーカー/サービスへの連絡先に関する情報。

Ryobi DP120についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもRyobi DP120の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRyobi DP120で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)