Norton C13の取扱説明書

22ページ 0.43 mb
ダウンロード

ページに移動 of 22

Summary
  • Norton C13 - page 1

    OWNERS MANUAL Small Concrete Saw MODEL: C13 FORM <<7317 3/2005 ...

  • Norton C13 - page 2

    2 WARRANTY Norton warrants all products manufactured by it against defects in workmanship or materials for a period of one (1) year from the date of shipment to the customer. The responsibility of Norton under this warranty is limited to replacement or repair of defective parts at Norton's Gainesville, Georgia factory, or at a point designated ...

  • Norton C13 - page 3

    3 Table Of Contents CONTENTS PAGE I. Preparation A. Safety Precautions 4-6 B. Assembly 7 C. C13 Series Concrete Saw Specifications 8 D. Engine Specifications 9 E. Pointer Alignment 9 II. Operation A. Blade Installation 9-10 B. Starting The Engine 10 C. Water Supply 10-11 D. Operating The Saw 11 E. Cutting Technique 12 III. Maintenance A. Engine 13- ...

  • Norton C13 - page 4

    4 I. PREPARATION A. Safety Precautions Important! The following safety precautions must always be observed. Hazard Symbols Fuel (gasoline) is extremely flammable and its vapors can explode if ignited. Store gasoline only in approved containers, in well- ventilated, unoccupied approved ar eas, and away from sparks or flames. Do not fill the fuel tan ...

  • Norton C13 - page 5

    5 Dust and Silica Warning Grinding/cutting/drilling of masonry, c oncrete, metal and other materials can generate dust, mists and fumes containing chemicals known to cause serious or fatal injury or illness, such as respirator y disease, cancer, birth defects or other reproductive harm. If you are unfam iliar with the risks associated with the part ...

  • Norton C13 - page 6

    6 1. Before mounting any blade on the saw, the blade should be inspected for any damage which might have occurred during shipment, handling or previous use. 2. The blade collars and arbors s hould be cleaned and examined for damage before mounting the blade. 3. The blade must be properly fitted o ver the arbor with the drive pin on the outside coll ...

  • Norton C13 - page 7

    7 I. PREPARATION B. Assembly The compact concrete saws are shipped completely assembled and ready for use except for diamond blade, gasoline, oil, and handle bar. Inspect the saw for shipping damage. If any damage is found, contact the shipper immediately and file a freight claim. The Norton Company is not responsible for any freight-related damage ...

  • Norton C13 - page 8

    8 C. C13 Series Concrete Saw Specifications Dimensions/Weight Length (Working) 45.66” (1160 mm) Length (Transport) 33.50” (850 mm) Width 39.50” (1003 mm) Height 39” (990 mm) Weight 220 lbs (100 kg) Engine Engine Mfg. Honda Spec No. GX390K1QXC9 Engine Type Single Cylinder 4 Cycle Horse Power 13 hp (9.5kW) @ 3,600 rpm Max Torque 19.5 ft-lbs ( ...

  • Norton C13 - page 9

    9 D. Engine Prior to attempting to operate the engine, read the information contained in the engine owner's ma nual. An engine owners manual is supplied with every gasoline powered concrete saw. 1. Check Oil: Add oil if low. Refer to the engine owner's manual for the recommended SAE viscosity grades. Capacit y of oil is 1.1 liters (1.16 U ...

  • Norton C13 - page 10

    10 2. Remove the blade shaft nut, (Turn clockwise) , and remove the outside collar. 3. Clean off any foreign particles on the clamping surfaces of both collars and on the mounting surface of the blade. 4. Place the blade on the blade shaft, lining up the drive pin hole in the blade with the drive pinhole in the inside collar. Use only Clipper Diamo ...

  • Norton C13 - page 11

    11 use of water greatly decreases t he amount of dust produced during the cutting process, aids in the cooli ng of the blade, and provides additional stability. • Use Only Water In The Water Tank • Do Not Drink From The Tank D. Operating the Saw 1. For blade installation instructions see section II. Operation sub heading A. Installing the Blade ...

  • Norton C13 - page 12

    12 13. When moving the saw to a new location, be sure the blade is not touching the ground. Always pay close attention to where you are moving and where the blade is at all times. E. Cutting Technique Lower the blade into the concrete to the required depth by turning the hand wheel clockwise. Reduce the forward pressure if the saw begins to stall. ...

  • Norton C13 - page 13

    13 III. MAINTENANCE A. Engine Follow the below schedule for engine maintenance. NOTE: Check the Honda Engine manual that came with the engine for any changes to the maintenance schedule. If the charts have any differences, follow the chart in the Honda Engine Manual. The Norton Company does not warranty the engine. If any warranty or service of the ...

  • Norton C13 - page 14

    14 Always refer to the engine manual for mo re detailed information on checking the oil, changing oil, and oil capacity, ai r filter changes, and fuel type to use. Use only Honda air filters. Do not clean the air filter with gasoline or other flammable solvents. A fire or explosi on could result. To clean, follow the instructions found in the Honda ...

  • Norton C13 - page 15

    15 For best results, bearings should be relubricated while in operation. Note: Due caution for personal safety must be observed when servicing rotating equipment. The grease should be pumped in slowly until a slight bead forms around the seals. Th is bead, in addition to acting as an indicator of adequate relubrication, provides additional protecti ...

  • Norton C13 - page 16

    16 7. Line up the straight edge along the outside face of both pulleys as shown in the drawing. 8. Misalignment will show up as a gap between the pulley face and the straight edge. 9. Make sure that the width of t he outside land (area between the belt and the edge of the pulley) is equal on both pulleys. D. Depth Control The depth control (raising ...

  • Norton C13 - page 17

    17 IV. PARTS LIST SECTION A. Ordering Information 1. List model number and serial number of machine. 2. List part number and serial num ber of part not the item number. 3. Wherever alternate par ts are shown due to product improvement, inspect the part you have and provide additional description as necessary. 4. Specify mode of shipping desired, su ...

  • Norton C13 - page 18

    18 ...

  • Norton C13 - page 19

    19 ...

  • Norton C13 - page 20

    20 Item DESCRIPTION Qty Part No 1 Basic Frame 1 83352 2 Rear axle assy. 1 82784 3 Rear Wheel 2 80991 4 Rear axle 1 82785 5 Front wheel complete 2 82786 6 Bushing Iglidur 20/23/11 4 80999 7 Bushing Iglidur (set of 2) 2 80297 8 Screw Feed.Spindle 1 82787 9 Raise-lower screw + key 1 83353 10 Bearing + Screw 1 76670 11 Stop ring A20 1 82789 12 Depth sc ...

  • Norton C13 - page 21

    NOTES ...

  • Norton C13 - page 22

    Norton Construction Products PO Box 2898 Gainesville, GA 30503 Phone: 800-554-8003 or 770-967-3954 (8:00 A.M. to 7:00 P.M. Eastern Time) Fax: 800-443-1092 or 770-967-7287 ...

メーカー Norton カテゴリー Saw

Norton C13のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- C13の取扱説明書
- Nortonの製品カード
- パンフレット
- またはNorton C13の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Norton C13の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Norton C13の取り付け説明書、サービスマニュアル、簡易説明書、またはNorton C13のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Norton C13の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Norton C13デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNorton C13を使用するのを助ける技術的文書のことです。説明書は通常、全てのNorton C13ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Nortonの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Norton C13の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNorton C13の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Norton C13に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Norton C13デバイスの基本機能を使うにあたってのヒント。 Norton C13のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Norton C13に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNorton C13のメーカー/サービスへの連絡先に関する情報。

Norton C13についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもNorton C13の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNorton C13で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)