-
Auto Page C3-RS1100 - page 1
C3 RS 1100 REV. A 1 C3 - RS 1100 OLED PROFESSIONAL 2 - WAY 915 MHz. OLED REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built - in Temperature Sensor And Two Way Serial Port Data Link INSTALLATION MANUAL Compatible THIS PRODUCT IS DESIG NED FOR PROFESSIONAL INSTALLATION ONLY ...
-
Auto Page C3-RS1100 - page 2
C3 RS 1100 REV. A 2 TABLE OF CONTENTS: INSTALLATION DIAGRAMS 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION 6 H1/1 Violet Wire – Starter Output 6 H1/2 & H1/3 Red Wire – +12V Power Input 7 H1/4 Yellow Wire – Ignition 1 Output 7 H1/5 Pink Wire – Ignition 2 Output 7 H1/6 Brown Wire – Accessory Output (Heater /ACC Ou tput) 7 H 5 : 5 PIN WHITE ...
-
Auto Page C3-RS1100 - page 3
C3 RS 1100 REV. A 3 Mechanical Neutral Safety Switch Considerations 31 Park/Neutral EC M Input 31 Key In Sensor Circuits 32 INTRODUCTION This Remote Starter with Alarm and Keyless Entry System has been designed to be installed on fuel - injected vehicles with an automatic transmission ONLY . n Never install this remote starter on a manual transmiss ...
-
Auto Page C3-RS1100 - page 4
C3 RS 1100 REV. A 4 INSTALLATION DIAGRAM ...
-
Auto Page C3-RS1100 - page 5
C3 RS 1100 REV. A 5 20A 20A Red: Remote Start Power 1 Red: Remote Start Power 2 Violet: Starter (+) Output Pink: Ignition 2 (+) Output Yellow: Ignition 1 (+) Output Brown: Acc/Heater (+) Output H1 6 PIN HEAVY GAUGE WIRE HARNESS H5 5 PI N WIRE HARNESS Red: 12v + Battery Power Brown: Siren ( + ) Output Black: System Main Ground ( - ) White: Parking L ...
-
Auto Page C3-RS1100 - page 6
C3 RS 1100 REV. A 6 WIRING Keep wiring away from moving engine parts, exhaust pipes and high - tension cable. Be sure to tape wires that pass through holes on the firewall to prevent fraying. CAUTION : Do not connect the wire harness to the control module until all wiring to vehicle is compl ete . H1: 6 PIN HEAVY GAUGE WIRING CONNECTIONS: Remember ...
-
Auto Page C3-RS1100 - page 7
C3 RS 1100 REV. A 7 Red Wire (2) — +12V Power Input Remove the two 20A fuses prior to connecting these wires and do not replace them until the satellite has been plugged into the control module. These wires are the source of current for all the circuits the relay satellite will energize. They must be connected to a high current source. Since the ...
-
Auto Page C3-RS1100 - page 8
C3 RS 1100 REV. A 8 been designed for use with all C I 3 compatible components. C I 3 Telematics system is available at any authorized Autopage dealer. This port will only operate correctly with Autopage C3 I - Datalink Modules . H 3 . 2 PIN WHITE CONNECTOR (THE LED STAT US INDICATOR): The led indicator status should be mounted in a highly visible ...
-
Auto Page C3-RS1100 - page 9
C3 RS 1100 REV. A 9 H 7 . 4 - PIN BLACK CONNECTOR. – TWO - WAY TRANSCEIVER/ANTENNA MODULE The Two - way transceiv er/antenna mounting location should be the upper left or lower left corner of driver’s windshield. For optimum range we suggest that the antenna be mounted Antenna tip facing down. Warning! Do not mount in such a manner that it obst ...
-
Auto Page C3-RS1100 - page 10
C3 RS 1100 REV. A 10 H 6 : 2 2 PIN WIRE CONNECTORS: H 6/1 BROWN/BLACK WIRE: 200 mA ( - ) Ground Output When Running. This wire provides a negative output during the remote start process. It can be used to operate by - pass modules that may be required in your installation. This wire will provide ground once the remote start process has been initiat ...
-
Auto Page C3-RS1100 - page 11
C3 RS 1100 REV. A 11 This output is for a Key Sense wire by - pass that some Chrysler and Toyota vehicles need to activate remote start. This wire come s on when remote start is activated and stays on for 20 seconds. H 6/ 4 White / Bule wire – (- ) Instant Start & Turn Off Input – This wires activates and turns off the remote starter each t ...
-
Auto Page C3-RS1100 - page 12
C3 RS 1100 REV. A 12 When the BLACK/WHITE wire is grounded, the remote start unit is operable. When this wire is open from ground, the remote start is disabled. 1. The optional “remote start toggle switch” can be added on to temporarily disable the Remote Start Device, it can prevent the vehicle from being remote started accidentally. This feat ...
-
Auto Page C3-RS1100 - page 13
C3 RS 1100 REV. A 13 Also on certain BMW, Mercedes Benz, Jaguar and Volkswagen cars, you can use this unique timed output to allow remote closure of all power window and sunroof without the need for an external module! H 6/1 2 Blue / Black wire – (- ) 200mA Accessory 2 Output – This wire provides a 200mA ( - ) ground output . This output will e ...
-
Auto Page C3-RS1100 - page 14
C3 RS 1100 REV. A 14 This wire provides a 200mA ( - ) ground output that becomes active 4 seconds before the remote start unit initialize, and remains grounded while running. Ignition 3 output: Some newer vehicles use a third ignition wire which is required to start and keep the vehicle’s engine running. If this is the case, wire an IGN 3 relay ( ...
-
Auto Page C3-RS1100 - page 15
C3 RS 1100 REV. A 15 To + 12 V Ignition Switch YELLOW wire Matching Resistor VATS control Module 87a 86 30 87 85 VAT wire (#1) VAT wire (#2) H 6/ 15 Green wire – Negative Door Switch Sensing Input (Zone 3) – This wire is the ground trigger input wire for negative door pin switch. This wire is connection for "grounding" type factory do ...
-
Auto Page C3-RS1100 - page 16
C3 RS 1100 REV. A 16 The WHITE/BLACK wire provides an instant shutdown for the remote start, whenever it is grounded. Connect the wire to the hood pin switch previously installed. This wire must be routed though a grommet in the firewall and connected to the hood pin switch. If the pin switc h is to be used with an alarm system, connect this wire w ...
-
Auto Page C3-RS1100 - page 17
C3 RS 1100 REV. A 17 VACUUM OPERATED CENTRAL LOCKING Green Wire Blue Wire +12V X Cut Compressor Door Switch 30 86 87a 85 87 30 86 87a 85 87 3 Pin Plug To Alarm VACUUM OPERATED DOOR LOCKING SYSTEM: TYPICAL OF MERCEDES BENZ AND AUDI. Locate the wire under the driver's kick panel. Use the voltmeter connecting to ground, verify that you have the c ...
-
Auto Page C3-RS1100 - page 18
C3 RS 1100 REV. A 18 2 STEP DOOR UNLOCK WIRE CONNECTION FOR GROUND SWITCHED DOOR LOCKS Cut Existing Unlock X Lock Unlock OEM Door Master Lock Switch To All Other Door Lock Motors Pink Wire OEM Door Lock Motor Existing Neg. Lock Wire Existing Neg. Unlock Wire 86 30 85 87 87a + 12V Green Wire Door Lock Blue Wire Door Unlock OEM Door Lock Relay H 10 / ...
-
Auto Page C3-RS1100 - page 19
C3 RS 1100 REV. A 19 4. Press the transmitter button corresponding to the feature you want to program. Press Transmitter Button One Chirp / LED one pulse Fact ory Default Setting Two Chirps / LED two pulses Three Chirps / LED three pulses Four Chirps / LED four pulses 1 Active arming Passive arming without passive door locking Passive arming with p ...
-
Auto Page C3-RS1100 - page 20
C3 RS 1100 REV. A 20 1 Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position . 2 Push the Valet switch 5 times (holding in on the 5 th push ) until two chirps with one long chir p is heard then release the valet switch. You are now in the Alarm feature “B” programming mode. 3 Press and release the transmitter button correspondi ...
-
Auto Page C3-RS1100 - page 21
C3 RS 1100 REV. A 21 (The system Can not be Arm with the engine running) The shock sensor will be by - passed upon engine running. (The engine will run by itself after the ignition is turned off) The shock sensor by - pass three minutes after armed. (The engine will run by itself after the ignition is turned off) Press and buttons at the same time ...
-
Auto Page C3-RS1100 - page 22
C3 RS 1100 REV. A 22 2 H 6 / 6 Brown / White Wire = ( - ) 200mA Horn Output H 6 / 6 Brown / White Wire = Factory Security Rearm Signal Output 3 Fahrenheit display for Temperature Celsius display For temperature 4 Override Without Password Pin Code Override With Password Pin Code 5 + H 6/7 Black / Green Wire Channel 4 Output = Pulsed out put H 6/7 B ...
-
Auto Page C3-RS1100 - page 23
C3 RS 1100 REV. A 23 Note 1 : If your built - in timer controls window/sunroof closure in your car DO NOT change the timer setting! This requires installer - only programming. Changing the value will adversely effect operation and may cause damage. Note 2: Momentary output = The momentary output s election will send a negative signal from the Chann ...
-
Auto Page C3-RS1100 - page 24
C3 RS 1100 REV. A 24 Program: 1. Press and release the transmitter button twice, [2] LED flash, [2] siren/horn chirp to indicate you are in features “Password pin code programming mode”. 2. Within 5 seconds, press and release the valet Switch 9 times. 3. Within 15 seconds of the last entered 9ths digit, t urn the Ignition Switch to “ON” pos ...
-
Auto Page C3-RS1100 - page 25
C3 RS 1100 REV. A 25 6 + Temperature - Control Starting OFF Te mperature - Co ntrol Starting “ON” 0 ºF / - 18 ºC Temperature - Cont rol Starting “ON” 15 ºF / - 9 ºC 7 + Press button = Activate Remote Start. Press - button = Activate Remote Start. Press + button = Activate Remote Start. 8 + H 6/4 White/Bl ue wire= 1 pulse activate H 6/4 ...
-
Auto Page C3-RS1100 - page 26
C3 RS 1100 REV. A 26 6 + “TEST” Mode for Zone 2 / instant tri gger & Zone 3 / Door trigger “TEST” Mode for Zone 1 & Zone 4 (2 Stage Shock Sensor) 7 + + 50 RPM DBI ONLY No RPM learning 8 + - 50 RPM DBI ONLY No RPM Learning or < 50RPM 9 + Automatic Transmission Exit: Press the button on the transmitter. 3 long chirps & 3 parkin ...
-
Auto Page C3-RS1100 - page 27
C3 RS 1100 REV. A 27 CHECK LEVEL PROGRAMMING: (TEST and ADJUST) 1. Press button once on the transmit ter to start the vehicle. 2. If everything goes well: a. Press button once on the transmitter to stop engine running. You have been completed this programming successfully. b. Press button on the transmitter to exit the program mode. There will be 3 ...
-
Auto Page C3-RS1100 - page 28
C3 RS 1100 REV. A 28 b. Press button on the transmitter to set proper “Start Timer”. The chirp & LED pause will confirm entry. (Increase “Start Timer ” is necessary.) c. Repeat steps 1 – 4. Timer Checking Type 1. Turn the Ignition 'switch ‘ ON/OFF’ 3 TIMES and stay in OFF position. 2. Push the Valet switch 11 times and hold i ...
-
Auto Page C3-RS1100 - page 29
C3 RS 1100 REV. A 29 b. Test the Zone 1 & Zone 4 / Two S tage Shock Sensor (Connected to H 9 4 Pin Plug) : Press and release the transmitter and button s at the same time again. [2] LED flash, [2] siren/horn chirps to indicate your are in the shock sensor (connected to H 9 4 pin plug) test mode. 1. Activate the war n - away (first stage of the ...
-
Auto Page C3-RS1100 - page 30
C3 RS 1100 REV. A 30 5. The remote start feature programming has not been programmed to start the vehicle. The rem ote start must be programmed how to start the vehicle. SHUTDOWN DIAGNOSTICS The unit has the ability to report the cause of the last shutdown of the remote start system. Enter: 1. Turn the Ignition switch to ‘ON position. 2. Press th ...
-
Auto Page C3-RS1100 - page 31
C3 RS 1100 REV. A 31 3. NEUTRAL START SAFETY TEST: 1. Set the vehicle parking brake. 2. Block the drive wheels to prevent vehicle movement. 3. Sitting in the vehicle, turn the ignition switch to “ON” or “RUN” position. But do not start the engine. 4. Step on the brake pedal and shift the gear selector into “DRIVE” (D). 5. Put your foot ...
-
Auto Page C3-RS1100 - page 32
C3 RS 1100 REV. A 32 Ignition P 1 2 D N R Electronic Control Module (ECM) Solid State, Do Not Measure Resistance To Neutral Safety Switch Input wire Black/White ( H 10 /1 ) Optional Enable Switch KEY IN SENSOR CIRCUITS: If the vehicle you are working on does not have or you cannot locate the ECM reference wire, there are two alternatives available. ...
-
Auto Page C3-RS1100 - page 33
C3 RS 1100 REV. A 33 (H 6 / 8 ) of the Remote Start Unit. F. Connect terminal 86 of the relay to a fused + 12 volt constant battery source. G. Connect terminal 87 of the relay to the Chime Module side of the previously cut wire in step D. H. Connect terminal 85 of the re lay to the Drivers Door side of the pin switch wire previously cut in step B. ...
-
Auto Page C3-RS1100 - page 34
C3 RS 1100 REV. A 34 Available At an Authorized Autopage Dealer The RS - 1100 is CI3 Compat ible It is recommended to have a minimal digital service plan on your cell phone. ...
-
Auto Page C3-RS1100 - page 35
C3 RS 1100 REV. A 35 BLANK PAGE ...
-
Auto Page C3-RS1100 - page 36
C3 RS 1100 REV. A 36 960 Knox Street Unit B Torrance, California 90502 Main Office: 310 - 323 - 1800 Technical Support: 8 00 - 945 - 2527 (For Authorized Dealers Only) ...
-
Auto Page C3-RS1100 - page 37
C3 RS 1100 REV. A 37 www.autopageusa.com 2 - Way Communication to the Power of 3 ...
Auto Page C3-RS1100についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもAuto Page C3-RS1100の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAuto Page C3-RS1100で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。