Makita 5077Bの取扱説明書

15ページ 0.86 mb
ダウンロード

ページに移動 of 15

Summary
  • Makita 5077B - page 1

    185 mm (744”) MODEL 5077B Equlpped wlth Electric Blade Brake Blade diameter 185 mm (7-1/4”) INSTRUCTION MANUAL Max. cutting capacity No load speed Overall length Net weight 62 mm (2-318”) 4,300 Rimin. 439 mm (17.114”) 6.3 kg (13.9 Ibs) DOUBLE INSULATION SPEC IF I CAT IONS ...

  • Makita 5077B - page 2

    IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 2 Keep work area clean. Cluttered areas and bench ...

  • Makita 5077B - page 3

    17. Extension cords. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and namepl ...

  • Makita 5077B - page 4

    VOLTAGE WARNING: Before connecting the tool to a power source (receptacle outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user, as well as damage the tool. If in doubt, DO NOT PLUG IN THE TO ...

  • Makita 5077B - page 5

    ADDITIONAL SAFETY RULES 1. Keep Guards In Place and In Working Order. Never wedge or tie lower guard open. Check operation of lower guard be- fore each use. Don’t use if lower guard does not close briskly over saw blade. CAUTION: If saw is dropped, lower guard may be bent, restricting full return. 2. Keep Blades Clean and Sharp. Sharp blades mini ...

  • Makita 5077B - page 6

    NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump back- wards over your hand, possibly causing severe injury. Fig. 7. Lower Guard. Raise lower guard with the retracting handle. 8. Adjustments. Before cutting be sure depth and bevel adjustments are tight. 9. Use Only Correct Blades In Mounting. Don’t us ...

  • Makita 5077B - page 7

    12. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. As examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, and Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down. DON'T TRY TO HOLD SHORT PLECE ...

  • Makita 5077B - page 8

    Removing or installing saw blade CAUTION : Always be sure that the tool is switched off and unplugged before removing or installing the blade. To remove the blade, press the shaft lock so that the blade cannot revolve and use the wrench to loosen the hex bolt clock- wise. Then remove the hex bolt, outer flange and blade. To install the blade, follo ...

  • Makita 5077B - page 9

    Adjusting depth of cut Loosen the lever on the depth guide and move the base up or down. At the desired depth of cut, secure the base by tightening the lever. Fig. 1 CAUTION : Use a shallow depth of cut when cutting thin workpiece for cleaner, safer cuts. *After adjusting the depth of cut, always tighten the lever securely. Bevel cutting Loosen the ...

  • Makita 5077B - page 10

    Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates pro- perly and returns to the "OFF" position when released. Operation Grasp the rear handle with your right hand, the front grip with your left. Set the base pla ...

  • Makita 5077B - page 11

    MAINTENANCE CAUTION : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be r ...

  • Makita 5077B - page 12

    OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory service center. Service centers are listed on the warranty card packed with your tool. CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of ...

  • Makita 5077B - page 13

    May-26-'87 US 185 mm (7-1/4") HYPOID SAW Model 5077B Note The switch, noise suppressor and other part conftguratlons may differ from country to country. 13 ...

  • Makita 5077B - page 14

    MODEL 50778 'iLM & DESCRIPTION May-26-'87 US 'iLM At., DESCRIPTION MACHINE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 36 37 38 39 40 1s - 1 1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1 1 1 3 1 1 1 2 1 4 4 2 2 1 1 1 1 2 1 1 1 1 4 - Hex Flange Hesd Bolt M8x20 Outer Flange 40 Inner Flange 40 Spindle ...

  • Makita 5077B - page 15

    MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight ...

メーカー Makita カテゴリー Saw

Makita 5077Bのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 5077Bの取扱説明書
- Makitaの製品カード
- パンフレット
- またはMakita 5077Bの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Makita 5077Bの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Makita 5077Bの取り付け説明書、サービスマニュアル、簡易説明書、またはMakita 5077Bのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Makita 5077Bの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Makita 5077Bデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがMakita 5077Bを使用するのを助ける技術的文書のことです。説明書は通常、全てのMakita 5077Bユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Makitaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Makita 5077Bの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははMakita 5077Bの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Makita 5077Bに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Makita 5077Bデバイスの基本機能を使うにあたってのヒント。 Makita 5077Bのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Makita 5077Bに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるMakita 5077Bのメーカー/サービスへの連絡先に関する情報。

Makita 5077Bについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもMakita 5077Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMakita 5077Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)