-
Mitsubishi FR-A5AR - page 1
TRANSIST ORIZED INVER TER -INSTR UCTION MANU AL- IB(NA)-66810-B (0201) MEE TRANSIST ORIZED INVER TER Printed in J apan Specifications subject to change without not ice. HEAD OFFICE:MITSUBISHI DENKI BLDG MAR UNOUC HI T OKY O 100-8310 FR-A5AR RELA Y OUTPUT ib66810b.book 1 ページ ２０ ０２年２月１５日 金曜日 午前 ８時１０分 ...
-
Mitsubishi FR-A5AR - page 2
A-1 Thank you for choosing the Mitsubishi transistor ized inverter option unit. This instruction man ual gives handling in formation and prec autions for use of this equipment. Incorrect handling might cause an unexpected fault. Before using the equipment, please read this manual carefully to use the equipment to its optimum. Please forward this ma ...
-
Mitsubishi FR-A5AR - page 3
A-2 2. Injury Preventio n 3. Additional inst ru ction s Also note the following points to prevent an accidental failure, injury , electric shock, etc.: (1) T ransportation and m ounting (2) T est o peration and adjustm ent ! Any person who is involved in the wir ing or inspection of t his equipment should be fully competent to do the work. ! Always ...
-
Mitsubishi FR-A5AR - page 4
A-3 (3) Usage (4) Mainten ance, inspe ction and pa rts replace ment (5) Disposal (6) General instructio n ! Do not modify t he equi pment. ! When parameter clear or a ll parameter clear is performed, each parameter retu rns to the factory setting. Re-set the re qu ired param e t ers before s t arting ope r a ti on. ! For prevent ion of damage due t ...
-
Mitsubishi FR-A5AR - page 5
CONTENTS 1.PRE -OP ERA TIO N INST RUCT IONS 1 1.1 Unpacking and Product Confirmation ..................................................................................................1 1.2 Packing Confirmation ........................................................................................................ ...................1 1.3 Structure ...
-
Mitsubishi FR-A5AR - page 6
1 1.PRE-OPE RATION INSTRUCTION S 1.1 Unpacking and Product Confirmation T ak e the option unit out of the package, check the unit name, and confirm that the product is as you ordered and intact. Functions arailable dif fer between FR-A500(L)/F500(L) series and FR-V500 series, always check before using. " SERIAL number check This product may be ...
-
Mitsubishi FR-A5AR - page 7
2 PRE-OPERATION INSTRUCTIONS 1.3 S tructure Front v ie w Mo unt in g holes Optio n fixing ho les Terminal symbol Terminal block scre w siz e M3 Rear vi ew Connect or FR- A5 AR 1A 1B 2A 2B 3C 1C 3B Mo unt in g holes 2C 3A Mo unt in g hole ib66810b.book 2 ページ ２０ ０２年２月１５日 金曜日 午前 ８時１０分 ...
-
Mitsubishi FR-A5AR - page 8
3 2.INSTALLATION 2.1 Pre-Installation I nstructions Make sure that the input power of the inverter is of f. 2.2 Installation Proc edure (1) Securely insert the connector of the option unit far into the connector of the inverter. At thi s time, fi t the option fixing holes snugly . For the position of slot, refer to the next page. Also be sure to fi ...
-
Mitsubishi FR-A5AR - page 9
4 INSTALLATI ON CAUTION 1. Only one type of opt ion per inverter may be used. When two or more option s are mounted, pri- ority is in order of slots 1, 2 and 3, the o ptions having lowe r priority are inoperative. 2. When the inverter cannot recogniz e that the option is mounted, it d isplays the option error . T he errors shown differ according to ...
-
Mitsubishi FR-A5AR - page 10
5 INSTALLATION 2.3 Wiring Route the wires so that the y do not take up a lot of space in the control circuit term inal block of the option unit. During wiring, do not leave wire of f-cuts in the inverter . They may cause a fault, failure or malfunction. Use the space on the left side of the control ci rcuit terminal unit to route the wires. REMARKS ...
-
Mitsubishi FR-A5AR - page 11
6 3.FUNCTIONS 3.1 Inte rnal Bl ock Diagram 3.2 Te rminals * The operation of each relay depends on the output signal selected. Y ou can selec t any three output signals available with an inverter as standard, and output them as relay contant signals. Functions arailable dif fer between FR-A500(L)/F500(L) series and FR-V500 series. The output signal ...
-
Mitsubishi FR-A5AR - page 12
7 4.PARAM ETE RS 4.1 Para m eter List By install ing this option unit, the parameters below are extended. Set the values according to need. The setting value of the parameter dif fers according to the inverter . Please refer to the inverter ins truction manual (output terminal function selection (Pr . 190 to)). (The setting value of negative logic ...
-
Mitsubishi FR-A5AR - page 13
8 5.THE C OMMERCIAL POWER SUPPL Y-INVERTER SWITC H-OVER SEQ UENCE FUNC TION If the commercial p ower suppl y-inverter swi tch-over seq uence functi on is acti vated with t he FR-A5AR mounted on the inverte r , th e phe nomen on wh ere ma gnet contac tor swi tch es al ternat e bet ween ON and O FF ma y occ ur . T o prev ent this, adapt either connec ...
-
Mitsubishi FR-A5AR - page 14
9 6.SPECIFICATIONS 6.1 S pecificat ions (1) Output signal type: contact output (three rela ys mounted) (2) Contact output: 230VAC 0.3A 30VDC 0.3A CAUTION The contacts shou ld be used within t he rated capacity to ensure long contact life. ib66810b.book 9 ページ ２０ ０２年２月１５日 金曜日 午前 ８時１０分 ...
-
Mitsubishi FR-A5AR - page 15
REVISIONS *The manu al nu mbe r is gi ven o n the b ott om l eft of th e bac k cov er . Print Date *Manual Number Revision Sep., 1997 IB(NA)-66810 -A First ed ition Jan., 20 02 IB(NA)-66810-B Adapt able inve rters Addit ion ib66810b.book 10 ページ ２ ００２年２月１５日 金曜日 午 前８時１０分 ...
Mitsubishi FR-A5ARについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもMitsubishi FR-A5ARの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがMitsubishi FR-A5ARで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。