QSC Audio DCA Seriesの取扱説明書

16ページ 0.8 mb
ダウンロード

ページに移動 of 16

Summary
  • QSC Audio DCA Series - page 1

    1 Cinema Accessories for DCA Series amplifiers USER MANUAL ▼ ▼ ▼ ▼ ▼ XC-3 Two-way crossover with delay ▼ ▼ ▼ ▼ ▼ LF-3 Low-frequency filter with delay ▼ ▼ ▼ ▼ ▼ SF-3 Subwoofer filter *TD-000079-00* TD-000079-00 rev. B ...

  • QSC Audio DCA Series - page 2

    2 ©Copyright 1998, 2002 QSC Audio Products, Inc. All rights reserved. “QSC , ” “DCA , ” “DataPort , ” and the QSC logo are registered trademarks of QSC Audio Products, Inc. EXPLANATION OF GRAPHICAL SYMBOLS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsul ...

  • QSC Audio DCA Series - page 3

    3 TABLE OF CONTENTS INTRODUCTION Introduction and d escription of e ach m odel.................................4 CONFIGURING THE ACCESSORIES General c onfiguration i nformation, all m odels...............................5 XC-3 Setting u p the XC-3....................................................................6 Factory -i nstalled SIPs......... ...

  • QSC Audio DCA Series - page 4

    4 INTRODUCTION & DESCRIPTION OF EACH MODEL XC-3 This accessory is a two-way crossover, with the low frequency band fed to channel 1 of the amplifier and the high frequencies t o channel 2. An all-pass filter on the low frequency band delays the audio signal, permitting time alignment of a cone driver with a high-frequency horn. A selectable hig ...

  • QSC Audio DCA Series - page 5

    5 CONFIGURING THE ACCESSORIES Configurable functions of the three accessory models Configure each accessory before you mount it to the ampli- fier. If an accessory is already mounted to an amplifier, always turn the amplifier off before changing switch set- tings, changing input or output connections, or detaching the accessory. Use the tables on t ...

  • QSC Audio DCA Series - page 6

    6 XC-3 Setting u p the XC-3 Setting up the XC-3 requires setting the DIP switches and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #2, #9, and #10 must be set to the ON position (default settings for the XC-3). The flowchart below takes you through all the steps necessary before mounting the accessory to the amp. The ...

  • QSC Audio DCA Series - page 7

    7 Use these tables to determine the correct resistor values for the crossover frequencies and delays you need. The shaded values are for the high-pass frequency (f HP ) of the XC-3. XC-3 Setting u p the XC-3 Effects of high frequency boost on frequency response (crossover frequency = 500 Hz). A boost of +10 dB is most common for compensating for sc ...

  • QSC Audio DCA Series - page 8

    8 Setup flowchart for the LF-3 Setting up the LF-3 requires setting the DIP switches and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #2 and #4 through #9 must be set to OFF, and switch #3 set to ON (factory default for proper operation). The flowchart , right, takes you through the steps necessary before mounting th ...

  • QSC Audio DCA Series - page 9

    9 LF-3 Setting Up the LF-3 LF-3 Factory-installed SIPs LF-3 Factory Switch Settings LF-3 Recommended Amplifier Settings f xo 350 Hz, both channels (18 k Ω SIP resistor installed in J6 and J8) Delay 1.4 milliseconds, both channels (22 k Ω SIP resistor installed in J1 and J2) Switch 1 and Switch 10 ON: Delay active (both channels) Switch 2 and Sw ...

  • QSC Audio DCA Series - page 10

    10 Setting up the SF-3 SF-3 Setting u p the SF-3 Setting up the SF-3 requires setting the DIP switches, and selecting/inserting SIP resistors into the appropriate sockets. DIP switches #1 through #6 and #10 must be set to OFF (factory default for proper operation). The flowchart, right, takes you through all the steps necessary before mounting the ...

  • QSC Audio DCA Series - page 11

    11 SF-3 Factory-installed SIPs fHP= 30 Hz (27 k Ω SIP resistor in J2) fLP= 250 Hz (22 k Ω SIP resistor in J6) SF-3 Factory Switch Settings Switches 1 through 6 and Switch 10 OFF: Default setting for SF-3 Switches 7 & 8 ON: Low-pass filter off (“cinema” setting) Switch 9 OFF: LF flat When shipped from the factory, the DIP switch settings ...

  • QSC Audio DCA Series - page 12

    12 An accessory may be mounted with the amplifier either in or out of the rack, even if the amp is installed with rear rack ears. MOUNTING- All Models Mounting the Accessories 1. Turn off the amplifier before installing the accessory. 2. Make sure the SIP resistor networks are installed properly and no SIP sockets are empty. 3. Line up the HD-15 co ...

  • QSC Audio DCA Series - page 13

    13 Setting up the DCA Accessories in the Cinema Sound System If you are unable to obtain a satisfactory frequency response or SPL on a channel, carefully check the wiring and connections. Some likely causes are reversed speaker polarity on one or more drivers, loose or broken wiring or connections, or blown or damaged speaker drivers. 1. Set up the ...

  • QSC Audio DCA Series - page 14

    14 Cleaning The faceplate and chassis can be cleaned with a soft cloth and nonabrasive, noncorrosive, mild cleaning solution. Products like Simple Green and Windex work well. Do not use powders or scrubbing pads of any type as they are usually abrasive and will permanently damage the finish of your cinema accessory. Dampen a soft, lint-free cloth w ...

  • QSC Audio DCA Series - page 15

    15 WORLD WIDE WEB: http://www.qscaudio.com FACSIMILE (FAX) NUMBERS: Sales & Marketing FAX +1 (714) 754-6174 Technical Services FAX +1 (714) 754-6173 TELEPHONE NUMBERS: Main Number +1 (714) 754-6175 Sales Direct Line +1 (714) 957-7100 or (800) 854-4079 toll free (U.S.A. only) Technical Services (714) 957-7150 or (800) 772-2834 toll free (U.S.A. ...

  • QSC Audio DCA Series - page 16

    16 © Copyright 1998, 2002 QSC Audio Products, Inc. All rights reserved. “QSC” and the QSC logo are registered with the U.S. Patent and Trademark Office. QSC Audio Products, Inc., 1675 MacArthur Boulevard Costa Mesa, California 92626 USA PH: (714) 754-6175 FAX: (714) 754-6174 ...

メーカー QSC Audio カテゴリー Stereo Amplifier

QSC Audio DCA Seriesのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- DCA Seriesの取扱説明書
- QSC Audioの製品カード
- パンフレット
- またはQSC Audio DCA Seriesの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、QSC Audio DCA Seriesの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、QSC Audio DCA Seriesの取り付け説明書、サービスマニュアル、簡易説明書、またはQSC Audio DCA Seriesのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、QSC Audio DCA Seriesの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

QSC Audio DCA Seriesデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがQSC Audio DCA Seriesを使用するのを助ける技術的文書のことです。説明書は通常、全てのQSC Audio DCA Seriesユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

QSC Audioの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. QSC Audio DCA Seriesの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははQSC Audio DCA Seriesの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。QSC Audio DCA Seriesに関してこのドキュメントで見つけることができる全てのヒントの目次
3. QSC Audio DCA Seriesデバイスの基本機能を使うにあたってのヒント。 QSC Audio DCA Seriesのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。QSC Audio DCA Seriesに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるQSC Audio DCA Seriesのメーカー/サービスへの連絡先に関する情報。

QSC Audio DCA Seriesについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもQSC Audio DCA Seriesの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがQSC Audio DCA Seriesで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)