-
Briggs & Stratton 1695287 - page 1
A TT A CHMENT OPERA T OR’S MANU AL 42” 2-Bin Bagger Mfg. No. Description 1695287 42” 2-Bin Bagger 1734239 Rev. 00 Rev. Date 01/2007 TP 100-4451-00-AT-SN 2-BIN B A GGER ...
-
Briggs & Stratton 1695287 - page 2
THIS P A GE INTENTIONALL Y BLANK ...
-
Briggs & Stratton 1695287 - page 3
1 Safety Rules & Inf ormation General W arnings ............................................2 Saf ety Decals ..................................................2 General Operating Instructions Bef ore Operation .............................................3 Mowing with the Catcher .................................3 After Operation .............. ...
-
Briggs & Stratton 1695287 - page 4
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This uni ...
-
Briggs & Stratton 1695287 - page 5
Bef ore Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i ...
-
Briggs & Stratton 1695287 - page 6
Initial Installation 4 W ARNING To avoid serious injury, engage parking brake, disengage PTO, stop engine, remove key and disconnect spark plug(s) before attempting to install, remove or work on the mower. NOTE: In this manual, “left” and “right” are always defined from the standpoint of the operator position facing forward from seat. COUNT ...
-
Briggs & Stratton 1695287 - page 7
5 Hitch Installation HITCH INST ALLA TION Hitch Installation 1. Remove 5/16-16 nut (G, Figure 2) from seat deck support capscrew (E). 2. Remove 3/8-16 nut (F) from rear debris guard capscrew (D). 3. Remove 1/2-13 nut (H) from rear of frame (A). 4. Remove 3/8-16 nut (I) from rear transmission support (J). 5. Attach hitch assembly (B) to frame (A) sl ...
-
Briggs & Stratton 1695287 - page 8
6 Bag Support and Cover Installation Figure 3. Install Bag and Cover Support A. Upright Support B. Bag and Cover Support C. Support Mount D. Mount Pin E. Retainer Spring F. Shoulder Rest G. Shoulder Bolt E A G B F D C C Bag Support Installation 1. Attach the bag and cover support (B, Figure 3) to the upright support (A) by sliding the support mount ...
-
Briggs & Stratton 1695287 - page 9
7 Bag Installation and T ube Assembly INSTALL COLLECTOR BAGS 1. Raise the cover (A, Figure 5). 2. Attach collector bags (B) using grass bag hanger (C) to bag hanger post (D). A D Figure 5. Install Collector Bags A. Cover B. Collector Bags C. Grass Bag Hanger D. Bag Hanger Post B C B A 42” Mowers 42” Mowers CONNECTING UPPER AND MIDDLE TUBE 1. Sl ...
-
Briggs & Stratton 1695287 - page 10
8 Chute and T ube Installation Chute Installation 1. Install 5/16 x 3/4” carriage bolts (D, Figure 7) with 5/16 push nuts (E) to mower deck as shown. 2. Lift discharge deflector(B). 3. Place the holes of the chute (A) onto carriage bolts (D, installed in step 1), sliding the front edge of the chute under the hinge bracket. 4. Secure knob (C) onto ...
-
Briggs & Stratton 1695287 - page 11
9 THIS P A GE INTENTIONALL Y BLANK ...
-
Briggs & Stratton 1695287 - page 12
Normal Installation & Removal 10 Figure 9. Normal Installation & Removal A. Hitch Support Assembly B. Bag and Cover Support Assembly C. Shoulder Bolt D. Mount Pin E. Retainer Spring F. Hinge Pin G. Retainer Spring H. Cover Hinge Pivots I. Cover J. Bag K. Bag Hanger L. Ridge Cutout M. Upper Tube N. Ridge O. Tube Assembly P. Rubber Strap Q. P ...
-
Briggs & Stratton 1695287 - page 13
Normal Removal 11 Remov al 1. Unhook rubber strap (P, Figure 9) from pin (Q), then remove tube assembly (O) from chute (R) and from cover (I). 2. Lift cover (I) and remove bags (J) from bag and cover support assembly (B). Note: Support the cover during the next step. 3. Remove cover (I) by disconnecting retainer springs (G), then remove both hinge ...
-
Briggs & Stratton 1695287 - page 14
Briggs & Stratton Yard Power Products Group Copyright © 2007 Briggs & Stratton Corporation Milwaukee, WI USA. All Rights Reserved MANUFACTURING, INC. Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.SimplicityMfg.com Simplicity Mfg. Inc. - Snapper Products 535 Macon Street McDonough, GA 30253 www.Sna ...
Briggs & Stratton 1695287についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもBriggs & Stratton 1695287の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがBriggs & Stratton 1695287で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。