Smeg WO-01の取扱説明書

23ページ 0.88 mb
ダウンロード

ページに移動 of 23

Summary
  • Smeg WO-01 - page 1

    INSTALLATION, USER AND MAINTENANCE MANUAL FOR WATER OSMOSIS UNIT WO-01 ...

  • Smeg WO-01 - page 2

    ...

  • Smeg WO-01 - page 3

    - 29 - EQUIPMENT FOR POTABLE WATER TREATMENT CONTENTS: P a r a g r a p h GENERAL WARNINGS................................................................................................................. TECHNICAL CHARACTER ISTICS ............................................................................................... POSITIONING AND INSTALLA ...

  • Smeg WO-01 - page 4

    - 30 - 1. General warnings STORAGE: THE PACKED APPLIANCE MUST BE STORED IN A DRY, CONDENSATION-FREE AREA, UNDER COVER. THE ADMITTED STO R AGE TEMPERATURE IS 4-50°C. ALWAYS DISCONNE CT ELECTRICAL POWER BEFORE WORKING ON THE APPLIANCE OR DISASSEMBLING IT. POSITIONING, HOOKUP, COMMISSIONING, TROUBLESHOOTING AND REPLACING POWE R CABLES MUST ALWAYS BE ...

  • Smeg WO-01 - page 5

    - 31 - 2. Technical characteristics Dimensions Height 814 mm Empty weight 60 kg Width 376 mm Empty weight including packagi ng 67 kg Depth 600 mm Installation chara cteri st ics Pow er cab le 3x1 length 1.5 m Di ame ter of was te di sch arg e p ip e 4 mm Plug Schuko Length of waste discharge pipe 1.5 m Length of filler pipe 1.5 m Delivery fitting 3 ...

  • Smeg WO-01 - page 6

    - 32 - Technical chara ct eri stics Single phase power voltage 230 v Frequency 50 Hz Osmosis pump power ratin g 450 w Delivery pump power rating 300 w Min/max water supply pressure 150-600 (1.5-6) kPa (bar) Max osmosis-treated water output 150 l/h Max water supply temperature 30 °C Max water supply hardnes s 40 °F Max water supply conductivity 2. ...

  • Smeg WO-01 - page 7

    - 33 - 3. Positioning and installation Positioning: Before installing the appliance, check that there is su ffi cient clearance for easy extraction of consum ables and for servicing the unit. Check that there is a power socket in the vicinity of the unit. The applian ce is designed for installation in clean area, protected from freezing tem p eratu ...

  • Smeg WO-01 - page 8

    - 34 - Water circuit and electrical hookup diagram Installing the membranes Open the front door to access the membrane housi ngs, which must be kept in their original packaging until the machine is started up Disconnect Und o Fit Screw on Reconnect the quick coupling the base the membrane the base the hoses hoses Membrane mount ...

  • Smeg WO-01 - page 9

    - 35 - Pressurizing and starting up the unit: After all pipes have been connected, pressurise the system gradually and check for leaks. Turn the “Osmosis pump” switch to “ I ”. Check that the following message displays: In normal operation the value Rj varies during osmosis-treated wate r prod uction. Wait 5-10 minutes, then continue by sta ...

  • Smeg WO-01 - page 10

    - 36 - 4. Maintenance The osmosis treatment unit runs com pletely automatically and maintenance is minimal. The only essential operation is periodic replacement of the filter cartridges. IMPORTANT Replace the pre-filter every 3000 hours of operation and AT LEAST 1 time a year . Pre-filter Membrane Replacing the pre-filter: Filter cartridge replacem ...

  • Smeg WO-01 - page 11

    - 37 - Special adjustments: RECIRCULATION Recirculation retreats the wa ste water to reduce the amount of water rejected. Turn the needle valve “Recirculation” to retreat the waste water, thus reducing overall wa ter consumption. Important! Make sure, when making adjustments, that the press ure gauge reading nev er exceeds 10 -11 bar. BYPASS Tu ...

  • Smeg WO-01 - page 12

    - 38 - 5. Plumbing diagram ...

  • Smeg WO-01 - page 13

    - 39 - LEGEND HYDRAULIC DI AGRAM IN Water inlet F 1 Product flow meter E 1 Filler solenoid valve P 2 Delivery minimum pressure switch P 1 Filler pressure switch R Vat cock FIL Filter - CA RBONLOK 5 micron M2 Delivery pump M1 Osmosis pump F 2 Waste flow meter S R “Re-treatment” needle valve E 2 Discharge solenoid valve VR Non-return valve SS Dis ...

  • Smeg WO-01 - page 14

    - 40 - 6. Wiring diagram ...

  • Smeg WO-01 - page 15

    - 41 - Electrical specifications: Power supply: 230v AC 50/60Hz Max motor outlet load: 16A_ at 230V AC Max load on solenoid valve 1 outlet: 1A_ at 230v AC Max load on solenoid valve 2 outlet: 1A_ at 230V AC Instrumentation: Conductivity meter (normalised at 20°C ) scale: 0-200 uS/cm with probe K=5. Class (overall): 1 Calibrated by samples. Switcha ...

  • Smeg WO-01 - page 16

    - 42 - 6- Faults Front door leds The door has two leds to indicate: - Green: power on, normal operatio n; - Red: fault, production of osmosis-treate d water stopped Important: THE DOOR GIVES NO INDICATION OF DELIVERY CIRCUIT FAULTS See below for details. Green Red List of faults A) No osmosis-treated water deliver y Possible causes Subcause Solutio ...

  • Smeg WO-01 - page 17

    - 43 - B) Osmosis-treated water not produced Possible causes Subcause Solution Display alarm message Check power supply and power switch ON (see “Positioning and installation”) No electrical power Power plug not inserted in electrical panel (insert) Check connections and whether board is sending a signal No power to pump Pump condenser faulty ( ...

  • Smeg WO-01 - page 18

    - 44 - C) Water production not conforming Display alarm message Cause of alarm Solution Adjust "bypass" needle valve HHHH The treated water does not conform with settings Replace membrane s Replace pre-filter (see mai ntenan ce section) Replace membranes (see maintenance section) LLLL The water production is below the set value Adjust &qu ...

  • Smeg WO-01 - page 19

    - 45 - Fig.3 Non-return valve Fig.4 Vat cock Fig.5 Pressure switch Solenoid valve Filter ...

  • Smeg WO-01 - page 20

    - 46 - 7. Electronic circuit board and programming Hold down F1 and press ENTER to enter conductivity programmi ng. We can now read the calibrated value. Press UP/DOWN to set the value. Press ENTER to save and quit. Press F1 to abort without saving. ...

  • Smeg WO-01 - page 21

    - 47 - In standby (system not running) : Pressing F1 runs a water flushing cycle. X.X indicates the software version (e.g. 2.1) Display: After a few minutes, switch off and on again with the osmosis pump switch. In stand by: hold down UP/DOWN together to enter programmi ng mode: (in all the following procedures: UP/DO WN changes the value, ENTER sa ...

  • Smeg WO-01 - page 22

    - 48 - Press ENTER or F1 : Stop motore se in moto per … (Stop motor after …) The following two messages concern the osmo si s pump motor condition. Set = 0 to exclude this mode; if the value is not 0, the motor stops running after having run continuously for the set period, then starts agai n. After two seconds, the system disp lays:>>> ...

  • Smeg WO-01 - page 23

    - 49 - Press ENTER or F1 ; the system returns to standby. The sw it ch at the top of the display, if pressed to the right, switches from the waste wa ter flow display to the osmo si s-treated water flow displa y. When it is released, the display returns to waste water flow mode. ...

メーカー Smeg カテゴリー Home Dialysis Equipment

Smeg WO-01のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WO-01の取扱説明書
- Smegの製品カード
- パンフレット
- またはSmeg WO-01の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Smeg WO-01の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Smeg WO-01の取り付け説明書、サービスマニュアル、簡易説明書、またはSmeg WO-01のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Smeg WO-01の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Smeg WO-01デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSmeg WO-01を使用するのを助ける技術的文書のことです。説明書は通常、全てのSmeg WO-01ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Smegの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Smeg WO-01の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSmeg WO-01の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Smeg WO-01に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Smeg WO-01デバイスの基本機能を使うにあたってのヒント。 Smeg WO-01のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Smeg WO-01に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSmeg WO-01のメーカー/サービスへの連絡先に関する情報。

Smeg WO-01についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもSmeg WO-01の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSmeg WO-01で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)