-
Porter-Cable SPEED-BLOC 330 - page 1
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...
-
Porter-Cable SPEED-BLOC 330 - page 2
2 T ABLE OF CONTENTS Read and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basic safety precautions should always be followed to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and propert ...
-
Porter-Cable SPEED-BLOC 330 - page 3
3 Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: ● lead from lead-based paints ● crystalline silica from bricks and cement and other masonry pro ...
-
Porter-Cable SPEED-BLOC 330 - page 4
4 Read all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. GENERAL SAFETY RULES SAVE THESE INSTRUCTIONS 1) Work area ...
-
Porter-Cable SPEED-BLOC 330 - page 5
5 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose ...
-
Porter-Cable SPEED-BLOC 330 - page 6
6 ADDITIONAL SPECIFIC SAFETY RULES 1. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. 2. Always disconnect the sander cord plug from th ...
-
Porter-Cable SPEED-BLOC 330 - page 7
7 SYMBOL DEFINITION V ........................ volts A ........................ amperes Hz ........................ hertz W ........................ watts kW ........................ kilowatts F ........................ farads µ F ........................ microfarads l ........................ litres g ........................ grams kg ........... ...
-
Porter-Cable SPEED-BLOC 330 - page 8
8 ADDITIONAL SAFETY RULES FOR P AINT REMOV AL Extreme care should be taken when removing paint. The peelings, residue, and vapors of paint may contain lead, which is poisonous. Exposure to even low levels of lead can cause irreversible brain and nervous system damage. Young and unborn children are particularly vulnerable. Before beginning any paint ...
-
Porter-Cable SPEED-BLOC 330 - page 9
9 If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amp ...
-
Porter-Cable SPEED-BLOC 330 - page 10
10 FUNCTIONAL DESCRIPTION FOREWORD Your Porter-Cable Finishing Sander is equipped to accept Stikit™ adhesive backed abrasives (4 1 / 2 " width) or conventional abrasive sheets (4 1 / 2 " x 5 1 / 2 "). This Sander is suitable for coarse, medium or fine sanding of wood, plaster, metal and plastics. It is ideal for leveling wallboard ...
-
Porter-Cable SPEED-BLOC 330 - page 11
11 TO ST ART AND STOP SANDER Make sure switch (A), Fig. 3, is in “OFF” position. 1. Make sure power source voltage is the same as specified on the sander’s specification plate. 2. Insert cord plug into power source outlet. 3. While holding sander firmly and off of work surface, slide switch (A), Fig. 3, to the “ON” position. 4. Allow sand ...
-
Porter-Cable SPEED-BLOC 330 - page 12
12 TROUBLESHOOTING GUIDE For assistance with your tool, visit our website at www.porter-cable.com for a list of service centers or call the Porter-Cable help line at 1-800-487-8665. FINE FINISHING The action of the Porter-Cable Finishing Sander causes thousands of tiny abrasive grits to move in circular orbits against the work at high speed. Each g ...
-
Porter-Cable SPEED-BLOC 330 - page 13
13 KEEP TOOL CLEAN Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth. NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear ANSI Z87.1 safety glasses while using compressed air. F AILURE TO ST ART Should your tool fail t ...
-
Porter-Cable SPEED-BLOC 330 - page 14
14 POR TER-CABLE LIMITED ONE YEAR W ARRANTY Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material ...
-
Porter-Cable SPEED-BLOC 330 - page 15
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): Auto-Set ® , BAMMER ® , B.O.S.S. ® , Builder’s Saw ® , Contractor’s Saw ® , Contractor’s Saw II™, Delta ® , DELTACRAFT ® , D ...
Porter-Cable SPEED-BLOC 330についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもPorter-Cable SPEED-BLOC 330の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable SPEED-BLOC 330で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。