-
K-Tec HP3A - page 1
Model HP3A Instruction Manual ...
-
K-Tec HP3A - page 2
...
-
K-Tec HP3A - page 3
T able of Contents SECTION P AGE # SECTION 1: IMPORT ANT SAFEGUARDS 1 SECTION 2: UNP ACKING 3 SECTION 3: BLENDER OVERVIEW 4 SECTION 4: INST ALLA TION 4 SECTION 5: CARE AND CLEANING 6 SECTION 6: OPERA TIONAL OVERVIEW 7 SECTION 7: TROUBLESHOOTING 8 SECTION 8: W ARRANTY 10 ...
-
K-Tec HP3A - page 4
HP-1 SECTION 1 IMPORT ANT INFORMA TION Read all instructions carefully before using your Blender™ 1.1 SAFETY CERTIFICA TION The blender is certied by ETL (Report No. 3018204-4, 3018204-2 & 3018204-3). 1.2 CERTIFICA TION Blender and its accessories are certied by NSF International (NSF), under K-TEC in the NSF Ofcial Listing. 1.3 A VO ...
-
K-Tec HP3A - page 5
HP-2 1.8 NEVER OPERA TE THE BLENDER USING A TT ACHMENTS NOT SOLD BY BLENDTEC The use of any unauthorized attachments may cause re, electric shock, and/or injury and will void the warranty . 1.9 CONT AINER MUST BE PROPERL Y IN PLACE WHILE APPLIANCE IS OPERA TING 1.10 BLADES ARE SHARP! HANDLE CAREFULL Y! 1.1 1 WHEN BLENDING HOT LIQUIDS, REMOVE CEN ...
-
K-Tec HP3A - page 6
HP-3 SECTION 2 SA VE ALL P ACKAGING MA TERIALS AND INSTRUCTIONS FOR FUTURE USE. 2.1 UNP ACKING YOUR BLENDER Y ou should have received the following items: • Motor base • Blender jar with lid • Recipe book 1. Remove blender motor , blender jar and lid from packaging. 2. Unwind the power cord. 3. Check for any packing material that may have blo ...
-
K-Tec HP3A - page 7
HP-4 SECTION 3 Blender OVERVIEW (Refer to Figures 1 and 2) 3.1 BLENDER MOTOR • Motor Cover: Houses the power unit in a durable, easy-to-clean polycarbonate. • T ouch Pad: Consists of six buttons that contain pre-programmed settings for selective blender control, a pulse button, and two speed control buttons. • LCD Information Center: will ind ...
-
K-Tec HP3A - page 8
HP-5 ...
-
K-Tec HP3A - page 9
HP-6 SECTION 5 CARE AND CLEANING 5.1 AFTER USE CLEANING 1. Add 1 cup of hot water and a drop of liquid dishwashing soap to the blender jar . 2. Place the lid tightly onto the jar . Place the blender jar on the blender base, and with your hand placed on top of the lid; press the pulse button for 5 seconds. 3. Rinse with clear water until all soap is ...
-
K-Tec HP3A - page 10
HP-7 SECTION 6 OPERA TIONAL OVER VIEW Y our Blendtec home blender has 30+ pre-programmed blend cycles for your con- venience, or optional manual controls. A representation of the controls is found below: 6.1 BEFORE YOU BEGIN OPERA TION 1. T urn on the main power switch located on the back of the blender motor in the lower right corner . The display ...
-
K-Tec HP3A - page 11
HP-8 6.3 AUTOMA TIC AND CUSTOM CONTROLS PRESETS: The four numbered buttons on the left side of the touchpad oper- ate four customizable pre-selected blend cycles. T o select one of these presets simply press the designated button. SELECTING A CYCLE FROM THE CYCLE MENU: T o access the Cycle Menu press the SELECT CYCLE MENU button. The Menu Mode LED ...
-
K-Tec HP3A - page 12
HP-9 6.4 RESTORING F ACTOR Y DEF AUL TS The Blendtec home blender has the following cycles set as factory defaults: BUTTON # CA TEGORY CYCLE NAME 1 Multi-Use Low Energy 2 Beverages Smoothie 3 Drinks/Ice Cream Mixed Drinks 4 Whole Foods Whole Juice T o restore your blender to these settings, press and hold preset button 4 and the ST ART/ST OP button ...
-
K-Tec HP3A - page 13
HP-10 SECTION 7 TROUBLESHOOTING 7.1 BLENDER MOTOR WILL NOT TURN ON If the blender motor will not turn on, try the following: • Make sure the main power switch on the back lower-right corner is turned ON. • Check your house circuit breaker switch or fuse, to make sure it is set to the ON position. • Unplug the power cord from the wall receptac ...
-
K-Tec HP3A - page 14
HP-1 1 7.3 BLENDED TEXTURE UNSA TISF ACTOR Y If the blended texture of product is lumpy or uneven, do the following: • Ensure the mixture is not cavitating during the cycle. Cavitation is a condi- tion in which the blender blade spins freely in an air pocket within the drink mix because the mix is too cold or too solid. This problem can be correc ...
-
K-Tec HP3A - page 15
HP-12 SECTION 8 W ARRANTY W ARRANTY DESCRIPTION (US Domestic and Canada) Y our Blendtec Blender motor is warrented for 3 years or 10,000 cycles, which- ever happens rst. The jar assembly , including all moving jar parts, is covered against leaking or breakage for 1 year . The blender jar blade and the motor base drive socket are covered by a lif ...
-
K-Tec HP3A - page 16
HP-13 UNDER W ARRANTY 1. Contact Blendtec immediately to diagnose the difculty . Please have blender serial number ready as well as a description of the problem. Do not attempt to do your own repairs. Repairs made by persons other than Blendtec authorized service representatives will void the warranty . Many issues can be resolved simply and qui ...
-
K-Tec HP3A - page 17
HP-14 1206 South 1680 West Orem, UT 84058 801-222-0888 blendtechome.com OWN-RE-023 Model HP3A Manual Rev . 02 12/06 ©2006 K-TEC, Inc., All Rights Reserved Blendtec is a registered trademark of K-TEC, Inc. ...
K-Tec HP3Aについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもK-Tec HP3Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがK-Tec HP3Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。