Acer WT 300の取扱説明書

54ページ 3.39 mb
ダウンロード

ページに移動 of 54

Summary
  • Acer WT 300 - page 1

    Acer WT 300 User’ s Guide Wbt.book Page 1 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 2

    Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to t ...

  • Acer WT 300 - page 3

    iii Notices FCC Notice This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if n ...

  • Acer WT 300 - page 4

    Notices iv Use Conditions This part complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian Users This Class B digital appara ...

  • Acer WT 300 - page 5

    v cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating. 9. Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric s ...

  • Acer WT 300 - page 6

    Notices vi Year 2000 Compliance Statement This product is Year 2000-compliant and carries the “ NSTL Hardware Tested Year 2000 Compliant ” logo. This product has been tested both by Acer ’ s internal test labs and NSTL using NSTL ’ s YMARK2000 certification test. These tests certify that this product will successfully make the year 2000 tra ...

  • Acer WT 300 - page 7

    vii T able of Contents Chapter 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Preinstallation . . . . ...

  • Acer WT 300 - page 8

    T able of Contents viii Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Troubleshooting Your Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Wbt.book Page viii Monday, Au ...

  • Acer WT 300 - page 9

    Getting Started Chapter 1 Wbt.book Page 1 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 10

    Chapter 1 Getting Started 2 Introduction Acer has been on the leading edge of microcomputer systems development for both corporate and home computing needs for 20 years, as the OEM of choice for many of the world ’ s leading computer companies. Acer is committed to meeting the world ’ s demand for state-of-the-art computers at the best prices. ...

  • Acer WT 300 - page 11

    3 Preinstallation The preinstallation process involves the following activities: · Selecting a site · Unpacking components Selecting a Site Consider the following when selecting a site for your computer: · Determine the best site for your system. Cable paths should not run near equipment that might cause electromagnetic or radio frequency interf ...

  • Acer WT 300 - page 12

    Chapter 1 Getting Started 4 Features The basic configuration consists of a system unit, a base holder , power adapter and it may also come with an optional SmartCard. Front Panel The figure below shows the system unit front panel. # Description 1 SmartCard slot 2 Power indicator 3 Manufacturer’ s logo Wbt.book Page 4 Monday, August 2, 1999 4:07 P ...

  • Acer WT 300 - page 13

    5 Rear Panel The figure shows the system unit rear panel. # Description 1 Parallel/Printer connector 2 Mouse connector 3 Ethernet connector 4 Main power switch 5 Power adapter jack Wbt.book Page 5 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 14

    Chapter 1 Getting Started 6 Note : As of now , Windows CE does not support the USB port, it will be available in the future. 6 USB ports 7 Keyboard connector 8 Serial connector 9 Monitor/VGA connector 10 Line-out/Speaker port # Description Wbt.book Page 6 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 15

    7 Connecting System Components Do not turn on the power until you finish connecting the system components. The following sections show how to connect each component to the system. Connecting the Keyboard Plug the keyboard cable into the keyboard connector on the rear panel. See the figure below. Wbt.book Page 7 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 16

    Chapter 1 Getting Started 8 Connecting the Monitor Plug the monitor signal cable into the VGA connector on the rear panel. Connecting the Mouse Plug the mouse cable into the mouse connector on the rear panel. Wbt.book Page 8 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 17

    9 Connecting the Printer If you have a parallel printer , connect it to the parallel connector on the rear panel. See figure below. Wbt.book Page 9 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 18

    Chapter 1 Getting Started 10 Connecting to the Network Plug into the network via the Ethernet connector to the hub. See figure below. Connecting the Power Adapter Plug one end of the power adapter to the power adapter jack, and then one end to the power cord, then plug the other end of the power cord into the wall outlet. Wbt.book Page 10 Monday, A ...

  • Acer WT 300 - page 19

    11 Connecting the Speaker The figure below shows the connection of the speaker to the system. Wbt.book Page 11 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 20

    Chapter 1 Getting Started 12 Using the Base Holder Y our system also includes a base holder to save precious table space. See figure below for the assembly. Wbt.book Page 12 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 21

    13 T urning On Y our System After you have connected all peripherals and cables, follow these steps to turn on your computer: 1. Turn on all peripherals connected to the system such as monitor , printer , etc. 2. Turn on the main power switch located at the back of the system. Note : If your system needs a SmartCard to power on, then insert the Sma ...

  • Acer WT 300 - page 22

    Chapter 1 Getting Started 14 T urning Off Y our System 1. Log off from the server and then tur n off the power of the system. 2. Turn off all peripherals connected to the system such as the monitor , printer , etc. 3. Turn off the main power switch and unplug the system if you are going to do any of the following ■ not use the system for a long p ...

  • Acer WT 300 - page 23

    15 Setup The setup refers to the Setup Wizard and the T erminal Properties. The Setup Wizard is used when the Acer WT 300 is installed for the first time. The T er minal Properties is used after the Setup Wizard is set. Setup Wizard The Setup Wizard lets you set terminal network configuration and terminal display parameters. Any future changes can ...

  • Acer WT 300 - page 24

    Chapter 1 Getting Started 16 Press next to go to the next screen. Read the end user ’ s license agreement carefully, press “ Accept ” to go to the next screen. Wbt.book Page 16 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 25

    17 If you choose the “ Y es, use the IP infor mation supplied by DHCP ” you will go directly to the dialog box where you provide the IP information. Choosing the “ No, I will enter status IP information ” option, press next and you will be asked to supply IP address, Subnet Mask and Gateway. If you do not know the information, you can ask y ...

  • Acer WT 300 - page 26

    Chapter 1 Getting Started 18 After supplying the necessary information, press “ Next ” , and you will have to supply additional information as shown below. Wbt.book Page 18 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 27

    19 When the necessary information is supplied, choose “ Next ” to set your video display resolution. The screen below shows the current setting of the video display resolution. Note : Make sure the resolution you select is supported by you monitor , otherwise your monitor will only display a blankscreen. After choosing your video display resolu ...

  • Acer WT 300 - page 28

    Chapter 1 Getting Started 20 If you choose “ OK ” the following screen will be displayed saying that you have successfully completed the Setup Wizard. Click “ Finish ” to apply the settings that you have chosen. After clicking the “ Finish ” , you will be asked to restart the system in order for the settings to take effect. Click on “ ...

  • Acer WT 300 - page 29

    21 T erminal Connection Manager T er minal Connection Manager dialog box is designed to help you manage your terminal's network connections. The dialog box displays after you are finish with the Setup Wizard. This is the screen that is displayed everytime you start your terminal and want to log onto a server . It can support up to seven differ ...

  • Acer WT 300 - page 30

    Chapter 1 Getting Started 22 3. On the “ New Connection ” dialog box, you can choose a “ Citrix ICA Client ” , “ Ericom Power Te rm Terminal Emulator ” or “ Microsoft Remote Desktop Client ” type of connection to create. Note: “Citrix ICA Client” and “Microsoft Remote Desktop Client” is a Windows NT based type of operating s ...

  • Acer WT 300 - page 31

    23 be added to the Connection Name list in the T er minal Connection Manager . Use the Back command button to go to the previous dialog box. Click on the Cancel command button to quit this dialog box at any time. The following figures show the sequence of the WTS Connection Wiza rd. Wbt.book Page 23 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 32

    Chapter 1 Getting Started 24 After you are finished with the configuration, you can get connected to a server by going to the connection option and double-clicking on a connection name or you can also highlight a connection name and click on “ Connect ” . Wbt.book Page 24 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 33

    25 Citrix ICA Client The following procedure describes how to create a network connection to a Citrix server . Creating a Network Connection 1. In the Connection Manager dialog box click the Configure tab and then click “ Add ” . 2. In the New Connection dialog box, click Citrix ICA Client in the type of connection list. Click “ OK ” . 3. I ...

  • Acer WT 300 - page 34

    Chapter 1 Getting Started 26 4. The Select a Citrix Server or Published Application screen will appear and If your Windows CE device is not on the same network as the Citrix server you want to connect to (for example, if you are on the other side of a router , across the Internet, or using RAS to connect to a remote network containing Citrix server ...

  • Acer WT 300 - page 35

    27 server on the remote network. Click “ OK ” . The Select a Citrix Server or Published Application screen reappears. Scroll through the list and select the name of the Citrix server or published application you want to connect to. Click “ Next ” to continue. 6. The Specify an Application screen will appears and in the Command Line field, e ...

  • Acer WT 300 - page 36

    Chapter 1 Getting Started 28 password when the ICA Windows CE Client connects to the Citrix server . Click “ Next ” to continue. 8. In the Select Window Option screen, select 16 or 256 colors from the Window Colors field. Click “ Next ” to continue. 9. In the Compression, Cache, and Sound screen, click Compress Data Stream to reduce the amo ...

  • Acer WT 300 - page 37

    29 recommended for low-bandwidth connections, including most modem connections. Click “ Next ” to continue. 10. By default, the Citrix server or published application name appears in the edit field. Y ou can accept this name or enter another . The name you choose will be the name of the entry in the Current Client Connections list and will appe ...

  • Acer WT 300 - page 38

    Chapter 1 Getting Started 30 a Windows 95 or Windows NT RAS server . Click "Next" to continue. 4. From the pull-down list in the Dial-In Devices screen, select your modem. In the Area, Phone Number , and Country fields, type the area code, phone number , and country code of the Citrix server . Click Next to continue. 5. From here on follo ...

  • Acer WT 300 - page 39

    31 Ericom Power T erm T erminal Emulator (Optional) 1. Select “ Ericom Power T er m T erminal Emulator ” and click on “ OK ” to go to the next dialog box. 2. On this dialog box, you will be asked to supply some information in order to connect to the server . Click on “ OK ” to add that to the T er minal Connection Manager ’ s Connecti ...

  • Acer WT 300 - page 40

    Chapter 1 Getting Started 32 Multiple Sessions T o start a multiple sessions: 1. From one of the active session: a. Press “ Ctrl+Alt+End ” ( “ End ” key on the editing keypad) to call up the T er minal Connection Manager . b. Click on another connection to connect and start another session. 2. From the T er minal Connection Manager: a. Clic ...

  • Acer WT 300 - page 41

    33 T erminal Properties T er minal Properties is used to change the setting of the terminal. This sections guide you through the steps on some of the features of T er minal Properties. 1. Everytime you press the F2 function key, the following screen will be displayed: a. Y ou can either click on okay to start your system or you can pick one of the ...

  • Acer WT 300 - page 42

    Chapter 1 Getting Started 34 3. Y ou can also choose the display option to set the video display resolution and to enable the screen saver . Note : Make sure the resolution you select is supported by you monitor , otherwise your monitor will only display a blankscreen. Wbt.book Page 34 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 43

    35 4. Click on the “ Network ” option to specify another network settings. Y ou can choose to “ Obtain an IP address from a DHCP server ” or “ Specify an IP address ” . The following screen shows the informations that needs to be supplied by the users. 5. Choosing the “ Specify an IP address ” will require you to supply the IP addre ...

  • Acer WT 300 - page 44

    Chapter 1 Getting Started 36 6. Choosing the “ Misc ” will enables you to put identification on your computer , enable remote upgrade function, control the sound volume and set the global ICA Client Setting. Wbt.book Page 36 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 45

    37 7. Below are the three screen shots of the Global ICA Client Settings. Wbt.book Page 37 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 46

    Chapter 1 Getting Started 38 Wbt.book Page 38 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 47

    Har dwar e Specifications Chapter 2 Wbt.book Page 39 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 48

    Chapter 2 Hardware Specifications 40 This chapter describes the hardware specification and all its major components. Major Components The system board has the following major components: ❑ CPU: Cyrix MediaGX L V 200 MHz internal speed ❑ Up to 256 MB Ram supported ❑ Ethernet Controller: AMD AM79C973 which supports 100BaseT and 10BaseT ❑ Exte ...

  • Acer WT 300 - page 49

    41 ■ DIMM type : 100 MHz SDRAM ■ Max DIMM module size : 256 MB VGA Controller ❑ Built in MediaGX with Virtual system architecture ❑ VGA memory size is shared with system memory Serial Port ❑ One high speed Ns 16c550 compatible UART built-in NS super I/O PC97317 ❑ Onboard 9-pin D type connector Parallel Port ❑ Standard Mode/ECP/EPP mod ...

  • Acer WT 300 - page 50

    Chapter 2 Hardware Specifications 42 Software Specification Bootloader ❑ Boot ROM - contains basic system initialization code and OS loader for Disk On Chip ❑ OS and application image stored in Disk On Chip Operating System ❑ Client side: Microsoft Windows CE 2.11 ■ Microsoft RDP Client ■ Citrix ICA Client ■ Ericom Power T er m T ermina ...

  • Acer WT 300 - page 51

    43 ❑ Serial and parallel port driver Application ❑ Acer customized logon screen ❑ T er minal configuration setup program ❑ Windows T erminal Client Wbt.book Page 43 Monday, August 2, 1999 4:07 PM ...

  • Acer WT 300 - page 52

    Chapter 2 Hardware Specifications 44 T roubleshooting Y our T erminal The following table lists some possible situations that may arise during the use of your terminal and provides easy answers and solutions. If you still encounter problems which you cannot resolve, please call any authorized dealer or distributor for assistance. Problem Solution W ...

  • Acer WT 300 - page 53

    45 The parallel printer connected to my terminal does not respond when I try to print to it. 1. Make sure that the printer is plugged into the proper outlet and is turned on. 2. Check the cable connection from the printer to the terminal. See “ Connecting the Printer ” on page 9 for more detail. 3. Make sure that the printer is on- line. 4. Mak ...

  • Acer WT 300 - page 54

    Chapter 2 Hardware Specifications 46 When a user improperly disconnects from the server , the user is not able to log on to the server again and the sound device does not work properly . If a user improperly disconnects from the server (i.e., suddenly turns off the power of the terminal without logging off), there will be an un-log off session in t ...

メーカー Acer カテゴリー Network Card

Acer WT 300のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WT 300の取扱説明書
- Acerの製品カード
- パンフレット
- またはAcer WT 300の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Acer WT 300の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Acer WT 300の取り付け説明書、サービスマニュアル、簡易説明書、またはAcer WT 300のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Acer WT 300の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Acer WT 300デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがAcer WT 300を使用するのを助ける技術的文書のことです。説明書は通常、全てのAcer WT 300ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Acerの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Acer WT 300の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははAcer WT 300の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Acer WT 300に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Acer WT 300デバイスの基本機能を使うにあたってのヒント。 Acer WT 300のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Acer WT 300に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるAcer WT 300のメーカー/サービスへの連絡先に関する情報。

Acer WT 300についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもAcer WT 300の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがAcer WT 300で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)