Nissan 6303の取扱説明書

34ページ 5.52 mb
ダウンロード

ページに移動 of 34

Summary
  • Nissan 6303 - page 1

    T YPE #1 6802/630 3 USB Consult Hardw are Installation Man ual V3.2 Type 1 - Rev3A/3B / 4 Boards (JECS ECCS 1984-1989 Legacy Engine Control Units, HITACHI ECCS/NICS 1985-1989 Legacy Engine Control Units) Copyr ig ht 2004, 2005, 2006, 2007, 2008, 2009 NIStune D evel opments ...

  • Nissan 6303 - page 2

    NIStune Type 1 Hardware Installation Page 2 of 2 I I N N T T R R O O D D U U C C T T I I O O N N Welcome to NI Stune. The NI Stune hardware and software solution provides a means for the c ar enthusiast to retune their vehicle whilst retaining their factory ECU and its default programming . This solution provides many a dvantages ove r aftermarke t ...

  • Nissan 6303 - page 3

    NIStune Type 1 Hardware Installation Page 3 of 3 TERMS AND CONDITIONS Nistune Develo pments has performed necessary measures to ensure that the Nistun e softwar e and boards a re built to high st andards. By using this p roduct you agree to the follow in g terms: I MPORTA NT - READ CAREFU LL Y: This License A gree ment ( Agreem ent ) is a legal agr ...

  • Nissan 6303 - page 4

    NIStune Type 1 Hardware Installation Page 4 of 4 Nistune Develo pments may, from time to time, revise or update th e Softw are. I n so doing, Nistun e Deve lopments incurs no obligation to furn ish such revision or updat es to yo u. 9. WARRA NTY The author of this Software has verified as best as possible that t he main features and functions of th ...

  • Nissan 6303 - page 5

    NIStune Type 1 Hardware Installation Page 5 of 5 WA RNING If y our ECU pulses the fuel pump, injectors, fuel regulator, flashe s LEDs ra ndomly (or they just stay on w hen they shouldn’t) or y our engine does not start then your ECU may not have y our boa rd fitted correctly. Testing has s how n on early Nissan ECUs that this c an potentially kee ...

  • Nissan 6303 - page 6

    NIStune Type 1 Hardware Installation Page 6 of 6 TABLE OF CON TENTS 1. Removing the ECU......................................................................................................................................... 7 2. Opening the ECU ........................................................................................................ ...

  • Nissan 6303 - page 7

    NIStune Type 1 Hardware Installation Page 7 of 7 1. Remov ing the ECU Loc ate the ECU in vehicle to be modified. The location of the fa ctory ECU can be identified from the vehicle service manual. The picture below shows the location of the ECU in the L HS passenger f oot well of an R31 Sky line. Disconnect y our negative battery terminal prior to ...

  • Nissan 6303 - page 8

    NIStune Type 1 Hardware Installation Page 8 of 8 2. Opening the ECU For NI S tune board installation, firstly remove the top and bottom lids from the ECU. Screws require a correctly matched Philips head screw driver as they are usually fitt ed from factory with a red or blue epoxy which requires some force in order to remove the scre ws. The follow ...

  • Nissan 6303 - page 9

    NIStune Type 1 Hardware Installation Page 9 of 9 3. Resocketing the ECU A . 1984-1985 Dual Board - Dual ROM ECUs Vehicles: Early Z31 300ZX and E12 Nissan Exa. This is a multiboard ECU with a 1K and 8K ROM chip. The two chips need to be removed and jumpers changed on the boa rd before the NI Stune board can be installed. The ROM images must be read ...

  • Nissan 6303 - page 10

    NIStune Type 1 Hardware Installation Page 10 of 10 To remove the two ROM chips (U3 and U4) desolder f rom the top side of the ECU. Be very c areful with the heat of the desoldering gun beca use the pads on these ECUs lift very easily. I t doesn't take much to break a trac k on these earlier circ uit boards. I nsert the supplied I C socket in I ...

  • Nissan 6303 - page 11

    NIStune Type 1 Hardware Installation Page 11 of 11 The below picture shows the removed I Cs, installed 28 pin m achine drilled socket and four wire link jumpers installed in their new locations. Next remove R15 which is below J9/J 10. This is no longer used with the NI Stune board installed. Note that You will no longer be able to use the fa ctory ...

  • Nissan 6303 - page 12

    NIStune Type 1 Hardware Installation Page 12 of 12 B. 1986 Single Board - Dual ROM ECUs Vehicles: Z31 300ZX VG30 1986-1987, CR31 / VL / VLT RB30 Some 1986 era ECU have both a 28 pin ROM and 24 pin ROM chip. These are loca ted next to each other. Not to be confused with the 24 pin RAM chip that is located next to the HD6802 processor. 1. Remove both ...

  • Nissan 6303 - page 13

    NIStune Type 1 Hardware Installation Page 13 of 13 2. Where the 28 pin ROM has been removed, replac e this with a 28 pin machine drilled socket. Fill in the throughholes where the 24 pin ROM was mounted with solder. Note the orientation of the socket must have the crescent indent fac ing the same direc tion of the previously i nstalled ROM chip. 3. ...

  • Nissan 6303 - page 14

    NIStune Type 1 Hardware Installation Page 14 of 14 C. 1987 Single Board - Si ngle ROM ECUs Vehicles: Z31 300ZX VG30 1987, VL RB30 These ECUs only contain a single chip such as pictured below one 28 pin ROM chip 1. Remove the factory ROM chip, install a 28 pin machine drilled socket 2. Then test that the ECU still works by placing the fac tory ROM c ...

  • Nissan 6303 - page 15

    NIStune Type 1 Hardware Installation Page 15 of 15 D. 1989 Single Board - Si ngle ROM - Header Connector ECUs Vehicles: Z31 VG30 late, HR31 RB20, S13 CA18, A31 RB20, EK10 MA09, S13 KA24E These ECUs either only contain a single chip such as shown in the pictures below. These contain a header connector which the NI Stune board connects to on this par ...

  • Nissan 6303 - page 16

    NIStune Type 1 Hardware Installation Page 16 of 16 S13 CA18DE/DET A31 RB20DE/DET ...

  • Nissan 6303 - page 17

    NIStune Type 1 Hardware Installation Page 17 of 17 EK10 MA09ERT / S13 KA24E 1. Remove the factory ROM chip, install a 28 pin machine drilled socket 2. Then test that the ECU still works by placing the fac tory ROM chip i n the socket and checking the vehicle runs and flashes L EDs when in diagnostic mode. I nstallation of the NI Stune board now fol ...

  • Nissan 6303 - page 18

    NIStune Type 1 Hardware Installation Page 18 of 18 4. CPU Header Connector Installation (X1) The NI Stune board will come supplied with two header conne ctors. One is for the USB socket and the other connects to the ECU processor (marke d HD6802 or HD6303) Early model ECUs wil l require direct connec tion to the processor, whilst later model ECUs p ...

  • Nissan 6303 - page 19

    NIStune Type 1 Hardware Installation Page 19 of 19 A . Early Model ECUs You need to solder the following wire s to the HD6802 processor similar to the picture below. The header c onnector y ou are supplied with is marked with a '1' on the left hand side. This corresponds to the 1 on the diagra m below. Solder the ends of the wires to the ...

  • Nissan 6303 - page 20

    NIStune Type 1 Hardware Installation Page 20 of 20 B. Later M odel ECUs La ter model ECUs connect directly to the circuit board using through holes provided by Nissan. Loc ate the header connec tor through holes and silkscree n and solder directly to this. 1989 Z31 300ZX Connector Wire 1 - ECU throughhole #33 Connector Wire 2 - ECU throughhole #32 ...

  • Nissan 6303 - page 21

    NIStune Type 1 Hardware Installation Page 21 of 21 J30 Maxima Connector Wire 1 - ECU throughhole D Connector Wire 2 - ECU throughhole C Connector Wire 3 - ECU throughhole B Connector Wire 4 - ECU throughhole A S13 CA18 / S13 KA24E Connector Wire 1 - ECU throughhole #1 Connector Wire 2 - ECU throughhole #2 Connector Wire 3 - ECU throughhole #3 Conne ...

  • Nissan 6303 - page 22

    NIStune Type 1 Hardware Installation Page 22 of 22 A31 RB20 Connector Wire 1 - ECU throughhole near 61 Connector Wire 2 - ECU throughhole ........... Connector Wire 3 - ECU throughhole ........... Connector Wire 4 - ECU throughhole near 9 HR31 RB20 Early : Connector Wire 1 - ECU throughole 3 Connector Wire 2 - ECU throughole 1 Connector Wire 3 - EC ...

  • Nissan 6303 - page 23

    NIStune Type 1 Hardware Installation Page 23 of 23 5. USB Connector Installation (X2) The USB-B sty le connector that comes with the NI S tune board is recommended for install where the diagnostic potentiometer normally sits. It is up to the owner where they wish to locate this port. The existing bracket from the diag nostic potentiometer fits the ...

  • Nissan 6303 - page 24

    NIStune Type 1 Hardware Installation Page 24 of 24 Then put the USB-B socket inside the bra cket and refa sten the bracket as see n below. I f y our ECU has no daughter board then the USB conne ctor board may face upwards. I f you ar e using a daughter boar d then ensure that the USB ada ptor board faces downwa rds and does not touch any other comp ...

  • Nissan 6303 - page 25

    NIStune Type 1 Hardware Installation Page 25 of 25 6. Inserting The Bo ard Push the NIStune boar d into the machine drilled socket previously inst alled. Connect the CPU cable to connector X1 and the USB c able to connector X2. Ensure the PGM jumper is not soldered if the board was previously programmed. Where there is a knock sensor boar d, being ...

  • Nissan 6303 - page 26

    NIStune Type 1 Hardware Installation Page 26 of 26 HR31 HR20 Installation ...

  • Nissan 6303 - page 27

    NIStune Type 1 Hardware Installation Page 27 of 27 7. Securing The Board I s is the responsbility of the installer to ensure that an vibration that the ECU is subjected with the installed NI Stune board (ie unsurface d roads, train lines, speed humps, gra tes etc) will not affect to opera tion of the vehicle. The NI Stune board must be installed us ...

  • Nissan 6303 - page 28

    NIStune Type 1 Hardware Installation Page 28 of 28 8. Installing In The Vehi cle Put the ECU casing back toge ther and reinstall ECU into the metal bracket. The dia gnostic indicator now containing the USB-B port should be accessible as seen be low. Reinstall ECU into vehicle. You may need to enlarg en kick panel diag nostics hole for correc t line ...

  • Nissan 6303 - page 29

    NIStune Type 1 Hardware Installation Page 29 of 29 9. Upgrading ECU MA F hardw are Early model engine control units such as Z31, R31, most HR31 (1985-1988) and VL Turbo use a 2 -7 volt hotwire airflow meter. These air flow meters then have their voltag e converte d to 0 - 5 volts for the internal microprocessor using wha t is known as 'opamp&a ...

  • Nissan 6303 - page 30

    NIStune Type 1 Hardware Installation Page 30 of 30 6. Rewire the AFM as per pinouts in the AFM section of the Nistune Software Users Manual 1987 - 1989 Z31 1. Disconnect parallel resistors pictured be low and and remove resistor R201 2. Rewire the AFM as per pinouts in the AFM section of the Nistune Software Users Manual ...

  • Nissan 6303 - page 31

    NIStune Type 1 Hardware Installation Page 31 of 31 1986-1988 HR31 RB20DET Note the later y ear models (such as MEC-R70 do not require this modification) 1. Loc ate opamp daughte r board 2. On reverse side of ECU count fr om the outside edge inwards a nd bridge pins 7 and 8 with solder. 3. Connect a 5.1 volt zener diode with stripe side on pin 8 and ...

  • Nissan 6303 - page 32

    NIStune Type 1 Hardware Installation Page 32 of 32 10. Reading the factory ROM image ECU Type A (1984-1985) These ECUs have two non-standard ROM chips (1K a nd 8K) which require spec ial adaptors to read them in a standard EPROM programmer . I t is recommended y ou send the ECU to NIStune developments for reading a nd board installation. We plan to ...

  • Nissan 6303 - page 33

    NIStune Type 1 Hardware Installation Page 33 of 33 1. So ensure y ou select the correct chip ty pe matching y our ROM/EPROM chip. Then select the read option which will load the contents from the chip into memory . 2. Then check the EPROM contents using a he x editor to ensure y ou read it corre ctly . S hould have data such as below. 3. Then save ...

  • Nissan 6303 - page 34

    NIStune Type 1 Hardware Installation Page 34 of 34 R R E E V V I I S S I I O O N N H H I I S S T T O O R R Y Y DATE VERSION DESCRIPTION 21/12/2005 1.0 Document Creation 24/01/2006 1.0.1 Correct HD6802 wiring to X3 hea der connection 11/6/2006 1.1 Pictures include Rev 2 board Cover different Z 31 variants Add HR31/CA18 ECU installation documentation ...

メーカー Nissan カテゴリー Stereo Receiver

Nissan 6303のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 6303の取扱説明書
- Nissanの製品カード
- パンフレット
- またはNissan 6303の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Nissan 6303の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Nissan 6303の取り付け説明書、サービスマニュアル、簡易説明書、またはNissan 6303のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Nissan 6303の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Nissan 6303デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがNissan 6303を使用するのを助ける技術的文書のことです。説明書は通常、全てのNissan 6303ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Nissanの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Nissan 6303の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははNissan 6303の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Nissan 6303に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Nissan 6303デバイスの基本機能を使うにあたってのヒント。 Nissan 6303のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Nissan 6303に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるNissan 6303のメーカー/サービスへの連絡先に関する情報。

Nissan 6303についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもNissan 6303の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがNissan 6303で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)