Xantrex Technology 18V 10Aの取扱説明書

32ページ 0.67 mb
ダウンロード

ページに移動 of 32

Summary
  • Xantrex Technology 18V 10A - page 1

    XPH Series 18V 10A DC Power Supply XPH 18-10 Operating Manual ...

  • Xantrex Technology 18V 10A - page 2

    About Xantrex Xantrex T echnology Inc. is a world-leading supplier of advanced power electronics and controls with products from 50 watt mobile unit s to one MW utility-scale systems for wind, solar , batteries, fuel cells, microturbines, and backup power applications in both grid-connected and stand-alone systems. Xantrex product s include inverte ...

  • Xantrex Technology 18V 10A - page 3

    Introduction The XPH 18-10 is an exceptionally comp act and lightweight single output laboratory dc power supply providing 0 to 18V at 0 to 10A. The XPH 18-10 uses mixed − mode regulation technology which combines switch − mode pre − regulation with linear post − regulation. S pecial techniques are used to maintain very high efficiency whil ...

  • Xantrex Technology 18V 10A - page 4

    Specification OUTPUT V oltage Range: 0V to 18V minimum Current Range: 0A to 10A minimum Output V oltage Setting: By coarse and fine controls. Output Current Setting: By single logarithmic control. Operating Mode: Constant volt age or const ant current with automatic cross-over . Output Switch: Electronic. Preset voltage and current displayed when o ...

  • Xantrex Technology 18V 10A - page 5

    Safety This power supply is a Safety Class I instrument according to IEC classification and has been designed to meet the requirements of EN61010-1 (S afety Requirement s for Electrical Equipment for Measurement, Control and Laboratory Use). It is an Installation Category II instrument intended for operation from a normal single phase supply . This ...

  • Xantrex Technology 18V 10A - page 6

    EMC This instrument has been designed to meet the requirements of the EMC Directive 89/336/EEC. Compliance was demonstrated by meeting the test limits of the following st andards: Emissions EN61326 (1998) EMC product standard for Electrical Equipment for Measurement, Control and Laboratory Use. T est limits used were: a) Radiated: Class B b) Conduc ...

  • Xantrex Technology 18V 10A - page 7

    Installation Mains Operating V olt age Check that the instrument operating voltage marked on the rear p anel is suit able for the local supply . Mains Lead When a three core mains lead with bare ends is provided this should be connected as follows: BROWN - MAINS LIVE BLUE - MAINS NEUTRAL GREEN/YELLOW - EARTH Safety Earth Symbol When fitting a fused ...

  • Xantrex Technology 18V 10A - page 8

    Operation Setting Up the Output With the POWER switch on ( l ) and the output off the output volt age and current limit can be accurately preset using the VOL T AGE and CURRENT controls; the left-hand meter shows the set voltage and the right-hand meter shows the set maximum current. When the output switch is switched on, the ON lamp lights; the le ...

  • Xantrex Technology 18V 10A - page 9

    Series or Parallel Connection with Other Outputs The outputs of the power supply are fully floating and may be used in series with other power supply units to generate high DC volt ages up to 300V DC. The maximum permissible voltage between any terminal and earth ground ( ) is 300VDC. W ARNING! Such voltages are exceedingly hazardous and great care ...

  • Xantrex Technology 18V 10A - page 10

    Calibration Allow at least 5 minutes warm-up before commencing calibration. Access to Calibration Adjustment s All adjustments are on the front p anel control board; all the trimmers are adjusted from the reverse side of the board through holes in the board. T o gain access to the board it is necessary to remove the top cover . W ARNING! When the i ...

  • Xantrex Technology 18V 10A - page 11

    V olt age Calibration Set the sense switch to local. Connect the DMM (set to V olts) across the output. Set volt age and current controls to minimum. Switch output ON (Check LED is on) and check for a reading of 00.00V ± 0.01V on the V olts display and DMM; check the Amps display reads 0.00 ± 0.01A. Set voltage and current controls to maximum. Ad ...

  • Xantrex Technology 18V 10A - page 12

    Sécurité Cet instrument est de Classe de sécurité 1 suivant la classification IEC et il a été construit pour satisfaire aux impératifs EN61010-1 (impératifs de sécurité pour le matériel électrique en vue de mesure, commande et utilisation en laboratoire). Il s'agit d'un instrument d'installation Catégorie II devant être ...

  • Xantrex Technology 18V 10A - page 13

    Installation T ension d’utilisation secteur Vérifier que la tension opérationnelle de l'instrument indiquée sur le panneau arrière est appropriée pour l'alimentation locale. Câble secteur Relier de la manière suivante tout câble secteur à trois conducteurs à fils nus: MARRON - SECTEUR SOUS TENSION BLEU - SECTEUR NEUTRE VERT/JA ...

  • Xantrex Technology 18V 10A - page 14

    F onctionnement Réglage de la sortie L ’interrupteur POWER (alimentation) sur ( l ) et la sortie éteinte, il est possible de régler avec précision la limite de tension et de courant de sortie au moyen des commandes VOL T AGE (T ension) et CURRENT (Courant); l’app areil de mesure gauche indique la tension réglée et l’appareil droit le co ...

  • Xantrex Technology 18V 10A - page 15

    Connexion en série ou en p arallèle avec d’autres sorties Les sorties de l’alimentation sont entièrement flott antes et elles peuvent être utilisées en série avec d’autres blocs d’alimentation, afin de produire des tensions c.c. jusqu’à 300 V c.c. La tension maximale admissible entre une borne et la terre ( ) est de 300 V c.c. A VE ...

  • Xantrex Technology 18V 10A - page 16

    Sicherheit Dieses Gerät wurde nach der Sicherheitsklasse (Schutzart) I der IEC-Klassifikation und gemäß den europäischen V orschriften EN61010-1 (Sicherheit svorschriften für elektrische Meß-, S teuer , Regel- und Laboranlagen) entwickelt. Es handelt sich um ein Gerät der Installationskategorie II, das für den Betrieb von einer normalen ein ...

  • Xantrex Technology 18V 10A - page 17

    Installation Netzbetriebssp annung Sicherstellen, daß die auf der Geräterückwand angegebene Betriebsspannung mit der V ersorgungsspannung am Ort übereinstimmt. Netzkabel S teht nur ein Netzkabel ohne S tecker zur V erfügung, so ist es wie folgt anzuschließen: BRAUN - STROMFÜHRENDER LEITER BLAU - NULLEITER GRÜN/GELB - SCHUTZLEITER Schutzleit ...

  • Xantrex Technology 18V 10A - page 18

    Betrieb Einstellung des Ausgangs Bei eingeschaltetem POWER-Schalter (Netz I ) und ausgeschaltetem Ausgang läßt sich die Ausgangsspannung und S trombegrenzung mit Hilfe der Knöpfe VOL T AGE (S pannung) und CURRENT (S trom) genau voreinstellen. Die linke Anzeige zeigt die eingestellte S pannung und die rechte den eingestellten Maximalstrom an. Wen ...

  • Xantrex Technology 18V 10A - page 19

    Leitungen miteinander verdrillt werden oder indem ein koaxial geschirmtes Kabel (Abtastung über den Innerleiter) verwendet wird. Auch ein Elektrolytkondensator direkt am Lastanschlusspunkt kann hier von Nutzen sein. Der S pannungsabfall darf bei keiner Ausgangsleitung mehr als 0.5 V olt betragen. Wenn die Istwert-Fernerfassung nicht benutzt wird, ...

  • Xantrex Technology 18V 10A - page 20

    W artung Die Hersteller bzw . deren V ertretungen im Ausland bieten die Reparatur von Geräten an, bei denen eine S törung aufgetreten ist. Wenn der Eigentümer die W artungsarbeiten selbst durchführen möchte, hat er dafür Sorge zu tragen, daß diese Arbeiten ausschließlich von entsprechend qualifiziertem Personal und gemäß W artungshandbuch ...

  • Xantrex Technology 18V 10A - page 21

    Sicurezza Questo strumento appartiene alla Categoria di Sicurezza 1, secondo la classifica IEC, ed è st ato progettato in modo da soddisfare i criteri EN61010-1 (requisiti di Sicurezza per Apparecchiature di misura, controllo e per uso in laboratorio). È uno strumento di Categoria d’installazione II ed è inteso per il funzionamento con un’al ...

  • Xantrex Technology 18V 10A - page 22

    Installazione T ensione d’esercizio Controllare che la tensione d’esercizio dello strumento segnata sul p annello posteriore sia uguale a quella della rete elettrica locale. Cavo d’aliment azione Quando viene fornito un cavo a tre fili con le estremità nude, collegare come segue: MARRONE LINEA BLU NEUTRO VERDE/GIALLO TERRA Simbolo di sicurez ...

  • Xantrex Technology 18V 10A - page 23

    F unzionamento Impost azione dell’uscit a Con l’interruttore POWER (alimentazione) regolato su ( l ) e l’uscit a su off (spent a), la tensione di uscita ed il limite di corrente possono essere preimpost ati accurat amente usando i comandi VOL T AGE (tensione) e CURRENT (corrente); il misuratore di sinistra mostra la tensione impostat a mentre ...

  • Xantrex Technology 18V 10A - page 24

    Collegamento in serie/p arallelo con altre uscite Le uscite del dispositivo di alimentazione sono complet amente flott anti e possono essere usate in serie con l’uscita di altri dispositivi si aliment azione per generare tensioni più alte, fino a 300V c.c. La tensione massima ammessa tra un morsetto qualsiasi e il morsetto di terra ( ) è 300Vc. ...

  • Xantrex Technology 18V 10A - page 25

    Seguridad Este es un instrumento de Clase de Seguridad I según la clasificación del IEC y ha sido diseñado para cumplir con los requisitos del EN61010-1 (Requisitos de Seguridad p ara Equipos Eléctricos para la Medición, Control y Uso en Laboratorio). Es un instrumento de Categoría de Inst alación II propuesto para ser usado con un suministr ...

  • Xantrex Technology 18V 10A - page 26

    Instalación T ensión de la Red Eléctrica V erificar que la tensión de funcionamiento del instrumento que figura en el panel trasero concuerde con el suministro local. Cable de Red Cuando se suministra un cable de tres conductores con puntas peladas, se deberá conect ar como sigue: MARRON - CORRIENTE DE RED AZUL - NEUTRO DE RED VERDE/AMARILLO - ...

  • Xantrex Technology 18V 10A - page 27

    Operación Ajuste de la Salida Con el interruptor POWER conectado ( l ) y se pueden preajust ar la salida de la tensión de salida y el límite de corriente con precisión usando los controles de VOL T AGE y CURRENT ; el medidor a la izquierda indica la tensión ajustada y el medidor a la derecha indica la corriente máxima preajustada. Cuando se c ...

  • Xantrex Technology 18V 10A - page 28

    Conexión en Serie o en Paralelo a Otras Salidas Las salidas del suministro de fuerza son completamente flot antes y pueden emplearse en serie con otras unidades de suministro de fuerza para generar altos volt ajes de CC de hast a 300V CC. La tensión máxima admisible entre cualquier borne y la tierra física ( ) es de 300 VCC. ADVERTENCIA! Dichos ...

  • Xantrex Technology 18V 10A - page 29

    W arranty Information W arranty What does this warranty cover? This Limited Warranty is provided by Xantrex Technology, Inc. ("Xantrex") and covers defects in workmanship and materials in your XPH series. This warranty lasts for a Warranty Period of three years (3 years) from the date of purchase at point of sale to you, the original end ...

  • Xantrex Technology 18V 10A - page 30

    What does this warranty not cover? This Limited Warranty does not cover normal wear and tear of the product or costs related to the removal, installation, or troubleshooting of the customer's electrical systems. This warranty does not apply to and Xantrex will not be responsible for any defect in or damage to: a) the product if it has been mis ...

  • Xantrex Technology 18V 10A - page 31

    Return Material Authorization Policy Before returning a product directly to Xantrex you must obtain a Return Material Authorization (RMA) number and the correct factory "Ship To" address. Products must also be shipped prepaid. Product shipments will be refused and returned at your expense if they are unauthorized, returned without an RMA ...

  • Xantrex Technology 18V 10A - page 32

    Xantrex Technology Inc. 8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 604 422 8595 Tel 604 421 3056 Fax 800 667 8422 Toll Free North Am erica prg.info@xantrex.com www .xantrex.c om 975-0104-01-02 48511-0740 Issue 2 ...

メーカー Xantrex Technology カテゴリー Power Supply

Xantrex Technology 18V 10Aのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 18V 10Aの取扱説明書
- Xantrex Technologyの製品カード
- パンフレット
- またはXantrex Technology 18V 10Aの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Xantrex Technology 18V 10Aの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Xantrex Technology 18V 10Aの取り付け説明書、サービスマニュアル、簡易説明書、またはXantrex Technology 18V 10Aのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Xantrex Technology 18V 10Aの製品を使用するにあたって最も人気のある説明書を閲覧できます。

Xantrex Technology 18V 10Aデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがXantrex Technology 18V 10Aを使用するのを助ける技術的文書のことです。説明書は通常、全てのXantrex Technology 18V 10Aユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Xantrex Technologyの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Xantrex Technology 18V 10Aの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははXantrex Technology 18V 10Aの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Xantrex Technology 18V 10Aに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Xantrex Technology 18V 10Aデバイスの基本機能を使うにあたってのヒント。 Xantrex Technology 18V 10Aのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Xantrex Technology 18V 10Aに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるXantrex Technology 18V 10Aのメーカー/サービスへの連絡先に関する情報。

Xantrex Technology 18V 10Aについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもXantrex Technology 18V 10Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがXantrex Technology 18V 10Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)