-
SkyLink TD-434 - page 1
Model: TD-434 User’ s Manual L CD Delux e Remote 15 01 : FR ...
-
SkyLink TD-434 - page 2
1 CONTENT INTRODUCTION................................................................................................... POWER UP ......................................................................................................... SET THE CLOCK .................................................................................................. ...
-
SkyLink TD-434 - page 3
2 INTRODUCTION SkylinkHome TM LCD Deluxe Remote allows you to wirelessly operate SkylinkHome TM various wireless receiver controls. This LCD Deluxe Remote provides features such as: - Zone Operation - Scene Operation - Timer Operation You can control various home appliances or lights with this remote control and different receiver units. Applicatio ...
-
SkyLink TD-434 - page 4
3 POWER UP Insert 2 AAA batteries to the remote (with the correct polarity as shown), its LCD display will turn on and red LED will ash once. Press the button on the remote, the red LED should ash. The remote is now powered properly. If the LCD display does not turn on or red LED does not ash when button is pressed, refer to Section “Bat ...
-
SkyLink TD-434 - page 5
4 PROGRAMMING THE LCD DELUXE REMOTE TO RECEIVER CONTROL In order to operate the receiver control with this LCD Deluxe Remote, it must be programmed to the receiver control. The LCD Deluxe Remote can transmit 4 types of command: 1) Individual Operation – Control one light only, i.e. the ceiling light in the family room. 2) Zone Operation – Contr ...
-
SkyLink TD-434 - page 6
5 PROGRAMMING FOR INDIVIDUAL OPERATION Individual operation allows you to use one of the buttons from 1 to 9 to control one specic light or appliance. To program a remote to the receiver control, a “Learn” code must be transmitted, follow the instructions below to transmit the “Learn” code to the receiver control. You may use the followi ...
-
SkyLink TD-434 - page 7
6 1. Put the receiver control that you plan to program into programming mode. Refer to the User’s Instructions of that receiver control. 2. During the standby mode, the LCD display will show the current time. Press the [PROG] button once to enter the Individual Programming mode. The Signal icon [ ] and red LED stays on for 15 seconds. 3. Once the ...
-
SkyLink TD-434 - page 8
7 PROGRAMMING FOR SCENE OPERATION Scene can provide specic brightness of multiple lights with a press of a button, this can create specic atmosphere. The remote provides 9 different scene settings, brightness of light control from 0% [off] to 100% [brightest], i.e. common scenes are morning scene, evening scene, movie scene and etc. To setup ...
-
SkyLink TD-434 - page 9
8 4. Now the Red LED stays on and the SCENE icon, Signal icon and Settings icon stay on for 15 seconds to allow you to program this scene to the receiver control. 5. Put the receiver control that you plan to program into programming mode. Refer to the User’s Instructions of that receiver control. 6. Once the receiver control is in programming mod ...
-
SkyLink TD-434 - page 10
9 You may assign a scene to specic receivers with preset brightness to create different atmosphere. Some examples below. Scene No. Scene Name Receiver Control Brightness 1 Evening Family Room Floor Light 30% 1 Evening Family Room Ceiling Light 40% 1 Evening Kitchen Floor Light 30% 2 Movie Kitchen Ceiling Light 30% 2 Movie Family Room Ceiling Lig ...
-
SkyLink TD-434 - page 11
10 1. Press the [PROG] button 5 times to enter the Timer Programming mode. The PROG icon and TIMER icon will stay on and the Timer number will ash in the LCD display. [show LCD] 2. Press [1 – 9] to select the Timer number you want to setup. 3. The day of the week (e.g. SU) will ash. Select the day you want the timer to be activated by using ...
-
SkyLink TD-434 - page 12
11 To Assign a Timer: 1. Press TIMER button once to select Timer mode. 2. Press [1 – 9] to select the desired timer, i.e. Enter [1] for Timer 1. 3. Press [PROG] to select between assigning this timer for: a. Individual Light / Device b. Zone c. Scene You can press [PROG] multiple times until the desired setting. 4. Use the Up [2] / Down [8] Butto ...
-
SkyLink TD-434 - page 13
12 To Activate or Deactivate the Timer: 1. During the standby mode, press [TIMER] once [show LCD]. 2. Press [1 – 9] to select the desired timer, i.e. Enter [1] for Timer 1. 3. Press [TIMER] again to activate or deactivate the timer. If the Timer icon stays on, the timer is activated. If the Timer icon is off, that timer is not activated. BATTERY ...
-
SkyLink TD-434 - page 14
13 WARRANTY If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required. CUSTOMER SERVICE If you would like to - nd out the up-to-date specications - know more ...
-
SkyLink TD-434 - page 15
14 ...
-
SkyLink TD-434 - page 16
15 101Z945 ...
SkyLink TD-434についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSkyLink TD-434の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSkyLink TD-434で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。