-
Troy-Bilt CSV206 - page 1
Chipper Shredder Vacuum Oper ator’ s Man ual IMPOR T ANT : Read saf ety rules and instructions carefully TRO Y -BIL T LLC P .O . BOX 361131 CLEVELAND , OHIO 44136-0019 Warning: This unit is equipped with an internal co mbustion engine and should not be used on or nea r any unimproved forest-covered, brush - covered or grass-covered land unless th ...
-
Troy-Bilt CSV206 - page 2
2 TABLE OF CONTENTS Content Page Important Safe Operation Practic es .. ................ ................ ............. ................ ....... 3 Assembling Your Chipper Shredder Va cuum ................ ................ ............. .......... 5 Know Your Chipper Shr edder Vacuum .......................... ................ ................ ..... ...
-
Troy-Bilt CSV206 - page 3
3 SECTION 1: IMPORTANT SAFE OPERATION PRACTICES Training 1. Read, understand, and follow all instructi ons on the machine and in the manual(s) before attempti ng to assemble and ope rate. Keep this manual in a safe place for future and regular re ference and for o rdering replacement parts. 2. Be familiar with all controls and their proper operatio ...
-
Troy-Bilt CSV206 - page 4
4 2. Before starting th e machine, make sure the ch ipper chute, feed intake, and cutting cham ber are empty and free of all debris. 3. Thoroughly inspect al l material to be shredde d and remove any metal, rocks, bott les, cans, or other foreign objects which could cause personal injury or damage to the machine. 4. If the impeller strikes a foreig ...
-
Troy-Bilt CSV206 - page 5
5 SECTION 2: ASSEMBLING YOUR CHIPPER SHREDDER VACUUM Unpacking • Remove staple s, break glue on top flaps, or cut tape at carton end an d peel along top flap to open carton. • Remove loose parts if included with unit (i. e., operator’s manu al, etc.) • Cut along cor ners, lay carton down f lat, and remove packing material. • Roll or slide ...
-
Troy-Bilt CSV206 - page 6
6 • Remove the thre e hex nuts and bell washers from the weld studs beside the op ening on the right side of the chipper-shred der vacuum. See Figure 4. Figure 4 • Place the chipper chute over the weld studs keeping the slotted sid e towards the bottom. Loosely secure with the three hex nu ts and bell washers that were removed earlier. Do not f ...
-
Troy-Bilt CSV206 - page 7
7 SECTION 3: KNOW YOUR CHIPPER SHREDDER VACUUM m Figure 7 Vacuum/Chipper Bag Collects shredded or chipped mat erial fed through the chipper chute or vacuumed up through the nozzle. See Figure 7. Chipper Chute Allow twigs and small bran ches up to 3” in diameter to be fed into the imp eller for chipping. See Figure 7. Tamper Plug This plug is inse ...
-
Troy-Bilt CSV206 - page 8
8 SECTION 4: OPERATING YOUR CHIPPER SHREDDER VACUUM • Read, under stand, and follow all instructio ns and warnings on the machine an d in this manual before operating. A pair of safety glasses has bee n provided with this equipm ent. Gas & Oil Fill-Up Service the eng ine with gasoline and oil a s instructed in the engine manual. Re ad instruc ...
-
Troy-Bilt CSV206 - page 9
9 SECTION 5: ADJUSTING YOUR CHIPPER SHREDDER VACUUM Front Caster Wheels This chipper shredder vacuum is equipped with front caster wheels. The casters can be locked in a straight ahead position or to swivel freely. • Lift and place pins in the larger holes for locked or straight ahead operation. See Figure 8. a. Place pins in smaller hole s to al ...
-
Troy-Bilt CSV206 - page 10
10 SECTION 6: MAINTAINING YOUR CHIPPER SHREDDER VACUUM Lubrication • Wheels: Lubricate the rear wh eels with light oil once a season. • Nozzle Door Adju stment Le vers: Lubric ate each adjustment lever once a season with light oil. • Front Caste r Wheels: Grease fittings are located on the front caster whee ls to provide easy lubrication of t ...
-
Troy-Bilt CSV206 - page 11
11 • When sharpening blades, follow the original angle of grind. Also, make sure to re move an equal amount fr om each blade a nd torque har dware to 250 - 300 in.lb. NOTE: Make sure th at blades are reassembled with the sharp edge facin g upward. Replacing the Belt NOTE: Because the engine on this equipment has a tapered crankshaft, a sp ecial i ...
-
Troy-Bilt CSV206 - page 12
12 Figure 17 • Press down on the belt guard spri ng by the idler pulley, and release the sprin g from the slot on the idler bracket. • Place the belt on the idle r pulley and place belt guard spring back int o the slot on the idler bracket. See Figure 17. • Place the mounting adapter again st the engine and make sure the hole in the mounting ...
-
Troy-Bilt CSV206 - page 13
13 SECTION 7: TROUBLESHOOTING NOTE: For repairs be yond the minor adjustments listed abov e, contact your nearest authorize d service dealer. Prob lem Cause Remedy Engine fails to start 1. Spark plug wire disconnected. 2. Fuel tank emp ty or stale fuel. 3. Throttle control lever not in corre ct starting posit ion. (If Equip ped) 4. Choke not in CHO ...
-
Troy-Bilt CSV206 - page 14
MANUF A CTURER’S LIMITED W ARRANTY FOR: The limited warranty set forth be low is given by Troy-Bilt LLC with respect to new merchandise purch ased and used in the United States, its possessions an d territories. “Troy-Bilt” warrants this produc t against defects in material and workmanship for a pe riod of two (2) years commencing on the date ...
Troy-Bilt CSV206についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもTroy-Bilt CSV206の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTroy-Bilt CSV206で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。