ページに移動 of 90
50 AC/LC REPARATURANLEITUNG MANUALE DI RIPARAZIONE MANUEL DE REPARATION MANUAL DE REPARACION REPAIR MANUAL 2002-2006 Art.NR.: 3.206.028-E ...
...
REPAIR MANUAL 2002-2006 50 AC/LC KTM Group Partner ...
...
1 SERVICE-INFORMATIONS 2 GENERAL INFORMATION 3 REMOVING AND REFITTING ENGINE 4 DISASSEMBLING ENGINE 5 SERVICING INDIVIDUAL COMPONENTS 6 ASSEMBLING ENGINE 7 TROUBLE SHOOTING 8 TECHNICAL SPECIFICATIONS 9 PERIODIC MAINTENANCE SCHEDULE 10 WIRING DIAGRAM 11 12 13 14 15 16 ...
...
Art.-Nr . 3.206.028 -E Repair manual KTM MINI 50 air/liquid cooled KTM REPAIR MANUAL IN LOOSE-LEAF FORM STORING THE REP AIR MANUAL IN THE BINDER – Put the index into the binder . – Put the front page of the repair manual (210x297 mm) into the transparent pocket provided for this purpose on the outside of the binder . – Put the spine label (17 ...
...
Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E E XPLANATION - U PDATE Edition: 7/2005 This repair manual contains the following supplements: 3.210.24-E Repair Manual 50 AC/LC 5/2001 Basic version Model year 2002 3.210.64-E Updating of Rep.Manual 3.210.24-E 5/2002 Model year 2003 (Engine number with first digit „3“) 3.206.010 ...
...
INTRODUCTION This repair manual offers extensiv repair -instructions and is an up-to-date version that describes the latest models of the series. However , the right to modifications in the interest of technical improvement is reserved without updating the current issue of this manual. A description of general working modes common in work shops has ...
...
Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E REPLY FAX FOR REPAIR MANUALS W e have made every effort to make our repair manuals as accurate as possible but it is always possible for a mistake or two to creep in. T o keep improving the quality of our repair manuals, we request mechanics and shop foremen to assist us as follows: ...
...
2-1E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E GENERAL INFORMATION OPERATING RANGES OF THE CARBURETOR . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 CLEANING AND STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3 BLEEDING OILPUMP FOR SEPARATE LUBRICATION . . . . . . . . . ...
...
B C D A 1 2 2-2E main jet jet needle jet needle idling jet idling jet throttle valve Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Carburetor adjustment Basic information about original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambien ...
2-3E Clean your motorcycle regularly in order to keep its painted finish looking shiny and new . The best manner would be to use warm water that has been mixed with a commercially available washing detergent and a sponge. The hard dirt can be removed before with the help of a soft water jet. ! CAUTION ! N EVER CLEAN YOUR MOTORCYCLE WITH A HIGH - PR ...
1 2 2 3 A 4 4 2-4E Bleeding oilpump for separate lubrication up to model 2003 Clamp oil lines 1 and 2 as shown. Add 2 stroke engine oil (for example Motorex Cross Power 2T) with a syringe until the bubble-free oil starts to leak out of the line 2 . After bleeding the oil pump, mount both oil lines and fill the oil tank with 2 stroke engine oil (for ...
Changing front brake fluid (not Mini Adventure) – Move the hand brake cylinder into horizontal position. – Disassemble the cover 1 together with the rubber boot 2 from the brake fluid reservoir . – Press the brake caliper pistons all the way back. – Use a syringe to extract the used brake fluid and add fresh DOT 5.1 brake fluid (Motorex Bra ...
Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Changing rear brake fluid (50 SX, 50 Supermoto) – Move the vehicle in a vertical position. – Disassemble the cover 1 together with the rubber boot 2 from the brake fluid reservoir . – Press the brake caliper pistons all the way back. – Use a syringe to extract the used brake ...
...
3-1E REMOVING AND REFITTING ENGINE Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E REMOVING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 INSTALLING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-4 INDEX 3 ...
...
1 2 3 4 5 6 3-2E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E Removing the engine NOTE: the following steps are shown on a model with LC-engine, on a model with AC-engine a few works are not necessary like draining coolant liquid, removing and mounting the radiator and the radiator shield, bleeding the cooling system. Clean the ...
1 2 3 4 5 3-3E – Loosen retaining bolt on tank 1 and remove from tank together with the rubber grommet. – Lift tank from the frame. – Open chain joint 2 and remove chain. – Loosen hose clamp 3 of the intake flange on the carburetor , pull carburetor back and swing to the side. NOTE: if the carburetor is not being serviced, it does not need ...
1 1 2 3 4 4 5 6 7 8 3-4E – Loosen hose clamp 1 and pull both hoses from their connections. – Unbolt radiator retaining bolt 2 and laterally remove radiator with water hoses from the frame. – Carefully pull socket connector 3 apart. – Detach both exhaust springs 4 with a suitable wrench, remove springs. – Unbolt the exhaust bracket on the ...
1 2 3 4 3-5E – Install carburetor on the intake flange and tighten hose clamp 1 . – Place chain on rear sprocket and pinion, mount chain joint 2 and secure. NOTE: make sure the locking member runs in the right direction (see photo). The closed side of the safety device must point in the running direction. – Mount tank and bolt tight. Do not f ...
1 2 3 3-6E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E – Attach connection 1 of the air filter box to the carburetor and tighten hose clamp. – Insert air filter element in the air filter box and mount cover . NOTE: the locating tabs in the cover must engage in the panel. – Mount seat. Make sure the retaining bracket 2 i ...
...
4-1E DISASSEMBLING THE ENGINE Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E SPECIAL TOOLS - ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-2 FIXING THE ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-3 DRAINING GEAR OIL . . . . . . . . . ...
...
15 50 8 130 75 2 1 4 3 5 6 4-2E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E SPECIAL TOOLS ENGINE 50 AC/LC FIG PARTNUMBER DESCRIPTION 1 590.29.021.000 Puller for flywheel 2 451.12.021.000 Rotor holding tool 3 451.29.006.000 Adjusting plate for Dimension „X“ 4 6 899 785 Loctite 243 blue 5 451.29.075.000 T achometer 6 503.29 ...
1 2 3 4 5 5 5 6 7 4-3E Clamp the engine using a vice – Clean the engine thoroughly prior to disassembling. – The engine can be clamped with a vice, using a protective pad to clamp the lower rear bracket (see photo). Drain the transmission oil – Remove the transmission oil drain plug 1 including the sealing ring and allow transmission oil to d ...
1 2 2 3 4 4 5 6 7 8 4-4E Remove ignition stator. – Pull cable guide 1 from the case. – Remove allan bolts 2 of the ignition stator 3 . – Carefully pull stator 3 out of the case. Remove cylinder head, cylinder and pistons. – Loosen bolts on cylinder head crosswise and remove. – Discard washers (LC-engine), remove cylinder head 4 . – Remo ...
1 2 3 4 5 5 5 5 6 7 7 4-5E Pull off ignition rotor – Hold ignition rotor 1 with special tool 2 , open the nut and remove. NOTE: a washer is located under the nut; the magnetic attraction of the rotor causes it to adhere to the rotor . ! CAUTION ! M AKE SURE THE TWO PINS OF THE SPECIAL TOOL DO NOT CA TCH THE THREADED HOLES , OTHERWISE THE THREADIN ...
1 1 1 1 2 3 4 5 6 7 8 9 4-6E Disassemble the clutch and primary drive – Rechuck the engine to provide access to the clutch side. – Remove kickstarter and bolts 1 on the clutch cover . – Remove clutch cover , discarding the seal. WARNING D O NOT REMOVE THE CIRCLIP 2 , OTHERWISE THE KICKST AR TER SPINDLE MAY F ALL FROM THE CASIN ...
...
5-1E SERVICING INDIVIDUAL COMPONENTS Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E RIGHT HOUSING HALF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2 LEFT HOUSING HALF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-3 CRANKSHAFT . . . . . . . . . . ...
...
1 2 3 S 5-2E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Working on the right half of the engine case Remove shaft sealing ring 1 and heat the engine case half on a heating plate to approx. 150° C. NOTE: if the engine case is heated to 150° C and struck on a wooden surface, the bearings usually fall out of the bearing seats ...
1 2 4 3 5-3E Working on the left half of the engine case Remove shaft sealing rings 1 / 2 and heat engine case halves on a heating plate to approx. 150° C. NOTE: – If the engine case is heated to 150° C and struck on a wooden surface, the bearings usually fall out of the bearing seats automatically . If necessary , the bearings must be pushed o ...
1 2 6 7 8 9 3 4 5 5-4E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Working on the clutch cover NOTE: dismantling the clutch cover is neccessary if parts are damaged or the O-ring is leaking. – T urn kickstarter shaft 1 counter -clockwise and remove ratchet gear 2 . Check gearing for wear . NOTE: If the kickstarter shaft is ...
M 4 6 8 7 5 3 2 1 9 5-5E Overhaul the water pump (LC-engine) – Remove cover 1 , discard the O-rings. – Remove circlip 2 with a suitable wrench. – Remove the water pump wheel 3 from the pump shaft 4 . – Press out shaft 4 , press out both bearings ( 6 and 7 ). – Remove seal shaft ring 5 . NOTE: a spring 8 is installed starting with the 2004 ...
x y 10mm x y 50mm 5-6E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E MARK PISTON CYLINDER AC CYLINDER LC A 39.455 - 39.460 mm 39.515 - 39.520 mm 39.505 - 39.510 mm 1.5533 - 1.5535 in 1.5557 - 1.5559 in 1.5553 - 1.5555 in B 39.461 - 39.465 mm 39.521 - 39.525 mm 39.511 - 39.515 mm 1.5535 - 1.5537 in 1.5559 - 1.5561 in 1.5555 - 1. ...
B A 1 2 3 4 5 6 7 6 6 5-7E Clutch new used Balancing the clutch wear – Check clutch shoes for wear; if the lining only shows minor signs of wear , the linings can be reinstalled. NOTE: – the centrifugal clutch has an outer diameter of approx. 82.5 mm (3.248 in) when new . – to compensate for minor wear in the lining, one of the preload washer ...
6-1E ASSEMBLING THE ENGINE Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E MOUNTING THE CRANKSHAFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2 MOUNTING THE PRIMARY DRIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2 MOUNTING LEFT ENGINE HOUSING . . . . . . . . . . . . . . ...
...
1 2 3 4 5 6 7 8 9 bk bl bl bl bl 6-2E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Mounting the crankshaft and output shaft – Heat the engine case on a heating plate. – Lubricate both bearings, lightly grease the seal shaft ring. – Push the output shaft and crankshaft into the bearing. NOTE: the conrod must be in a verti ...
1 2 3 4 5 5 6 7 S 8 9 6-3E – Wrap insulating tape around the output shaft in the area of the sharp edge 1 to prevent the seal shaft ring from being damaged. NOTE: wrap insulating tape just above edge to allow the tape to be easily pulled off after the seal shaft ring is mounted. – Grease the seal lip and press in the seal shaft ring. – Pull o ...
2 3 2003 1 1 1 1 4 4 4 2 3 2004 6-4E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Mounting the clutch cover – Put new seals in place and mount the clutch cover . – Bolt clutch cover into place with 6 bolts M6x25 1 , tighten the bolts to 10 Nm (7 ft.lb). Mount the ignition cover and water pump. – Put the dowels 7x ...
1 3 4 2 6-5E Mount the pistons – Fix conrod with a mounting board. – Grease the conrod bearings and attach to conrod eye. – Mount pistons, the arrow on the bottom of the piston should point towards the outlet port. – Slide piston pin into the conrod eye by hand and mount piston pin lock with the open side facing down. – T urn the piston r ...
1 1 2 3 4 6-6E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Mount the cylinder head – Mount the cylinder head 1 , making sure the water connection is on the intake side (LC-engine). – Use new washers for the cylinder head bolts (LC-engine), tighten cylinder head bolts crosswise in 2 stages to 15 Nm (11 ft.lb). Mount water ...
...
7-1E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E TROUBLE SHOOTING TROUBLE SHOOTING 50 AC/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2 IGNITION MEASUREMENT 50 AC/LC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-4 MEASUREMENT WITH PEAK VOLTAGE ADAPTER . . . . . . . . . . . ...
...
7-2E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TROUBLE CAUSE REMEDY Engine fails to start Operating error Open fuel tap, replenish fuel, do not use choke Fuel supply interrupted Close fuel tap, loosen fuel hose at carburettor , lead into a basin and open fuel tap, – if fuel leaks out, clean carburettor – if no fuel leak ...
7-3E TROUBLE CAUSE REMEDY Engine stalling or running with four stroke cycle Carburetor overflows if level adjust too high, float needle seating is dirty or enlarged Clean carburetor , if necessary replace float needle and adjust level Loose carburetor jets T ighten jets High rpm misfiring Incorrect heat range spark plug or low quality spark plug Re ...
1 2 R S 7-4E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E Resistor values of the ignition system - Stator – Unplug the ignition stator and measure the resistance of the stator using a digital measuring tool. – The resistance must be 500 Ω ± 40 Ω at 20º C. NOTE: it is not neccessary to take the stator out of the engin ...
...
8-1E MODEL 2002 ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 BASIC CARBURETOR SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3 CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-4 ...
...
8-2E MODEL 2005 AC ENGINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10 BASIC CARBURETOR SETTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-10 CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11 ...
...
8-3E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TECHNICAL DATA - ENGINE 50 AC/LC 2002 Engine 50 AC (aircooled) 50 LC (liquid cooled) Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49,0 cm³ Bore/Stroke 39,5 / 40 mm Fuel SUPER fuel, research octane no 95, mixed with 2-stroke oil Oil/gasoline ratio ...
8-4E TECHNICAL SPECIFICATIONS - CHASSIS 50 MINI 2002 50 SX PRO SENIOR LC single downtube, split-cradle Marzocchi Ø = 32 mm 175/185 mm (6.9/7.3 in) Central shock absorber WP PDS Disc brake Ø 160 mm (6.3 in) Drumbrake Ø 90 mm (3.5 in) front/rear 2.50x10" Pirelli MT 32 / 2.75x10" MT 320 front/rear: 1.0 bar / 1.0 bar 1,8 Liter 11 : 48 1/2x ...
8-5E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TECHNICAL DATA - ENGINE 50 AC/LC 2003 Engine 50 AC (aircooled) 50 LC (liquid cooled) Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49,0 cm³ Bore/Stroke 39,5 / 40 mm Fuel SUPER fuel, research octane no 95, mixed with 2-stroke oil (separate lubricati ...
8-6E TECHNICAL SPECIFICATIONS - CHASSIS 50 MINI 2003 50 SX PRO SENIOR LC single downtube, split-cradle Marzocchi Ø = 32 mm 175/185 mm (6.9/7.3 in) Central shock absorber WP PDS Disc brake Ø 160 mm (6.3 in) Drumbrake Ø 90 mm (3.5 in) 2.50x12" V eeRubber V270/ 2.75x10"V271 front/rear: 1.0 bar / 1.0 bar 1,8 Liter 11 : 48 1/2x3/16" 10 ...
8-7E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TECHNICAL DATA - ENGINE 50 AC/LC 2004 50 SX PRO SENIOR LC single cylinder 2-stroke engine, with reed valve inlet 49,0 cm³ 39,5 / 40 mm Lead-free SUPER FUEL (ROZ 95), mixed with 2-stroke oil 1 : 40 when using high grade 2-stroke oil (Motorex 2T Cross Power) When in doubt, pleas ...
8-8E BASIC CARBURETOR SETTING Model 50 MINI ADVENTURE (SEP ARA TE LUBRICA TION) 50 SENIOR ADVENTURE (MIXTURE LUBRICA TION) T ype Dell'Orto PHV A 12 XS Dell'Orto PHV A 14 DS Main jet 60 80 (70) Needle jet 211 F A 211 F A Idling jet 38 45 Jet needle A10 A10 Needle position from top 4. 3. Air/Mixture reg. screw open 4 3,5 Slide 40 40 Startin ...
8-9E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TECHNICAL SPECIFICATIONS - CHASSIS 50 MINI 2004 50 SX PRO SENIOR LC single downtube, split-cradle Marzocchi Ø = 32 mm 185/185 mm Central shock absorber WP PDS Disk brake Ø 160 mm Disk brake Ø 140 mm 2.50x12" Pirelli MT 32A 2.75x10" Pirelli MT320 1,0 bar / 1,0 bar 1 ...
8-10E TECHNICAL DATA – ENGINE 2005 AC ENGINE 50 AC SENIOR ADVENTURE 50 AC MINI ADVENTURE Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49.0 ccm Bore/Stroke 39.5 / 40 mm Fuel Lead-free SUPER FUEL (ROZ 95), mixed with 2-stroke oil Lead-free SUPER FUEL (ROZ 95) Lubrication mixture lubrication separate lubrication Oil/gas ...
8-11E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TECHNICAL SPECIFICATIONS – CHASSIS 2005 AC CHASSIS 50 SENIOR ADVENTURE 50 MINI ADVENTURE Frame single downtube, split-cradle Fork Marzocchi Ø = 32 mm (1,26 in) Wheel travel front/rear 175/190 mm (6.9/7.5 in) 115/185 mm (4,5/7,3 in) Rear suspension Central shock absorber Pai ...
8-12E TYP 50 SX PRO JUNIOR LC 50 SX PRO SENIOR LC Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49.0 ccm Bore/Stroke 39.5 / 40 mm Fuel SUPER fuel, research octane no 95, mixed with 2-stroke oil Oil/gasoline ratio 1 : 40 when using high grade 2-stroke oil (Motorex 2T Cross Power) When in doubt, please contact your import ...
8-13E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E 50 SX PRO JUNIOR LC 50 SX PRO SENIOR LC Frame single downtube, split-cradle Fork Marzocchi Ø = 32 mm (1.26 in) Wheel travel front/rear 140/205 mm (5.5/8 in) 185/185 mm (7.3/7.3 in) Rear suspension Central shock absorber WP Front brake Disk brake Ø 160 mm (6.4 in) Rear brake ...
8-14E TECHNICAL DATA – ENGINE 2006 AC ENGINE 50 SENIOR ADVENTURE 50 MINI ADVENTURE Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49.0 ccm Bore/Stroke 39.5 / 40 mm Fuel Lead-free SUPER FUEL (ROZ 95), mixed with 2-stroke oil Lead-free SUPER FUEL (ROZ 95) Lubrication mixture lubrication separate lubrication Oil/gasoline ...
8-15E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E TECHNICAL SPECIFICATIONS – CHASSIS 2006 AC CHASSIS 50 SENIOR ADVENTURE 50 MINI ADVENTURE Frame single downtube, split-cradle Fork Marzocchi Ø = 32 mm (1,26 in) Wheel travel front/rear 175/190 mm (6.9/7.5 in) 115/185 mm (4,5/7,3 in) Rear suspension Central shock absorber Pai ...
8-16E TYP 50 SX JUNIOR 50 SX, 50 SUPERMOTO Design single cylinder 2-stroke engine, with reed valve inlet Displacement 49.0 ccm Bore/Stroke 39.5 / 40 mm Fuel SUPER fuel, research octane no 95, mixed with 2-stroke oil Oil/gasoline ratio 1 : 60 when using high grade 2-stroke oil (Motorex 2T Cross Power) When in doubt, please contact your importer Lubr ...
8-17E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E 50 SX JUNIOR 50 SX 50 SUPERMOTO Frame single downtube, split-cradle Fork Marzocchi Ø = 32 mm (1.26 in) Wheel travel front/rear 140/205 mm (5.5/8 in) 185/185 mm (7.3/7.3 in) Rear suspension Central shock absorber WP Front brake Disk brake Ø 160 mm (6.4 in) Rear brake Drum bra ...
8-18E TOLERANCES AND FITTING CLEARANCES Crankshaft run out of crank stud max. 0.050 mm Crankshaft webs outer dimension 38 mm ±0.05 mm Conrod bearing radial play max. 0.030 mm Piston fitting clearance 0.055-0.065 mm (AC) / 0.045-0.055 mm (LC) Piston ring end gap max. 0.20 mm Clutch shoes outer diameter new 82.5 mm Clutch drum diameter max. 84.4 mm ...
9-1E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028-E LUBRICATION AND MAINTENANCE SCHEDULE 50 AC/LC MODEL 2002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-2 MODEL 2003-2005 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-4 MODEL 2006 . . ...
9-2E M AINTENANCE WORK DONE BY KTM AUTHORISED WORKSHOPS IS NOT A SUBSTITUTE OF CARE AND CHECKS DONE BY THE RIDER ! PERIODIC MAINTENANCE 2002 50 MINIS air/liquid cooled A washed motorcycle can be checked more quickly which saves money! Service Service every every 5 hours 20 hours ENGINE Check engine for leaks Change transmission oil Check sp ...
9-3E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E VITAL CHECKS AND CARE PROCEDURES TO BE CONDUCTED BY THE OWNER OR THE MECHANIC before each start after every cleaning for cross country use once a year Check transmission oil level Check coolant level Check brake fluid level Check brake pads for wear Check brake ...
9-4E PERIODIC MAINTENANCE 2003-2005 50 MINIS air/liquid cooled A washed motorcycle can be checked more quickly which saves money! Service Service every every 5 hours 20 hours ENGINE Check engine for leaks Change transmission oil Check spark plug, change it if necessary , set electrode gap Check the clutch engagement speed CARBURETOR ...
9-5E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E NOTE: I F THE INSPECTION EST ABLISHES THA T PERMISSIBLE TOLERANCES ARE EXCEEDED , THE RESPECTIVE COMPONENTS MUST BE REPLACED . VITAL CHECKS AND CARE PROCEDURES TO BE CONDUCTED BY THE OWNER OR THE MECHANIC before each start after every cleaning for cross country use once a year ...
9-6E M AINTENANCE WORK DONE BY KTM AUTHORISED WORKSHOPS IS NOT A SUBSTITUTE OF CARE AND CHECKS DONE BY THE RIDER ! PERIODIC MAINTENANCE 2006 50 MINIS air/liquid cooled A washed motorcycle can be checked more quickly which saves money! Service Service before every every every 5 hours 20 hours race ENGINE Check engine for leaks Change transmi ...
9-7E Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E NOTE: I F THE INSPECTION EST ABLISHES THA T PERMISSIBLE TOLERANCES ARE EXCEEDED , THE RESPECTIVE COMPONENTS MUST BE REPLACED . VITAL CHECKS AND CARE PROCEDURES TO BE CONDUCTED BY THE OWNER OR THE MECHANIC before each start after every cleaning for cross country use once a year ...
...
10-1E 10 WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-2 WIRING DIAGRAM INDEX Repair manual KTM MINI 50 air/liquid cooled Art.-Nr . 3.206.028 -E ...
l i o c n o i t i n g i C L 0 5 r o i n e S X S - . d A i n i M black 4 0 0 2 . 2 0 . 0 2 G k c a l b n o t t u b p o t s k c a l b r o t a r e n e g 10-2E Cable colours: black = black ...
KTM 50 AC/LCのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 50 AC/LCの取扱説明書
- KTMの製品カード
- パンフレット
- またはKTM 50 AC/LCの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、KTM 50 AC/LCの取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、KTM 50 AC/LCの取り付け説明書、サービスマニュアル、簡易説明書、またはKTM 50 AC/LCのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、KTM 50 AC/LCの製品を使用するにあたって最も人気のある説明書を閲覧できます。
KTM 50 AC/LCデバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがKTM 50 AC/LCを使用するのを助ける技術的文書のことです。説明書は通常、全てのKTM 50 AC/LCユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
KTMの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. KTM 50 AC/LCの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははKTM 50 AC/LCの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。KTM 50 AC/LCに関してこのドキュメントで見つけることができる全てのヒントの目次
3. KTM 50 AC/LCデバイスの基本機能を使うにあたってのヒント。 KTM 50 AC/LCのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。KTM 50 AC/LCに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるKTM 50 AC/LCのメーカー/サービスへの連絡先に関する情報。
KTM 50 AC/LCについてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもKTM 50 AC/LCの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがKTM 50 AC/LCで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。