Husqvarna SC18/968999352の取扱説明書

14ページ 0.11 mb
ダウンロード

ページに移動 of 14

Summary
  • Husqvarna SC18/968999352 - page 1

    Operators manual SC18/968981201 SC18/968999352 Models: Please read these instructions carefully and make sure you understand them before using the machine. MANUAL NO. 540200156 REV . 01 (12/01/05) ...

  • Husqvarna SC18/968999352 - page 2

    2 CONTENTS SPECIFICA TIONS U.S. Metric Engine - Honda: 5.5 hp 3.8 kw Net Weight: 328 lbs 149 kg Shipping Weight: 360 Ibs 164 kg Width: 24 in 61 cm Height: 36 in 91 cm Length: 54 in 137 cm Cutting Depth (max): 2.5 in 6.3 cm Cutting Width: 18 in 46 cm Index Operator ’ s Guide Page Specifications ..................................................... ...

  • Husqvarna SC18/968999352 - page 3

    3 FEA TURES AND CONTROLS Oil used in the engine (gray cap) 1. Refer to your engine manual for oil type, viscosity , weight and capacity . Oil used in the Clutch/Gear Box 1. Refer to your engine manual for oil type, viscosity , weight and capacity . Reducer (yellow cap) T ransmission grease used 1. Y ou should not need to service the transmission. C ...

  • Husqvarna SC18/968999352 - page 4

    4 OPERA TING INSTRUCTIONS GENERAL INFORMA TION This manual will assist you in the safe operation and proper maintenance of your Husqvarna equip- ment. Read it thoroughly before attempting to operate the machine. Do not hesitate to call your dealer or Husqvarna if additional information is required. The following safety symbols are used throughout t ...

  • Husqvarna SC18/968999352 - page 5

    5 OPERA TING INSTRUCTIONS • Do not attempt sharp turns while cutting. • Should I water before cutting? It is usually not necessary to water before cutting. In extreme conditions, such as clay soil that is very compacted, a simple test as follows will determine if you need to water before cutting. Use a garden hand spade, weed tool, or even a la ...

  • Husqvarna SC18/968999352 - page 6

    6 SAFTEY AND MAINTENANCE CAUTION Any modifications or additions to this equipment without written authorization from the manufacturer will void all manufacturer ’s warranties. Do not operate this machine without first reading owners manual. CAUTION Husqvarna parts have been designed and specified to meet commercial operating standards for strengt ...

  • Husqvarna SC18/968999352 - page 7

    7 SERVICE AND MAINTENANCE BLADE WEAR Sod cutter blades may wear quickly depending on soil condition. Replace blade when worn to 1 1/2” (3.8cm) or less. Maintain lower blade surface. CLEANING AND W ASHING Regular cleaning and washing will prolong the service of your machine. Note: Use care with power washers to avoid damage to W arning Decals, Ope ...

  • Husqvarna SC18/968999352 - page 8

    8 TROUBLESHOOTING PROBLEM ANSWER/COMMENT T ransmission shaft broke 1. Ensure debris is not caught in the T ransmission Chain or wrapped around the transmission output shaft. 2. Ensure the unit has a Skid Pan installed. 3. Contact your servicing dealer . Drive wheels won’t engage 1. Ensure the Drive Chain is on all sprockets. 2. Ensure the T ransm ...

  • Husqvarna SC18/968999352 - page 9

    9 PROBLEM ANSWER/COMMENT Chain (Drive) is coming off, The T ransmission Output S procket is a fixed (non adjustable) drive sprocket wearing sprocket which is splined and snap-ringed in place. 1. Align the Axle Sprockets (double set screws) to the T ransmission Output S procket. Position the Axle Sprockets the same distance from the chassis wall. 2. ...

  • Husqvarna SC18/968999352 - page 10

    10 PROBLEM ANSWER/COMMENT Blade not disengaging New Unit or New Belt: 1. Run the machine with the blade engaged until the belt stretches. Used Unit or Old Belt: 1. Adjust the Belt Keeper so each leg touches when idler pulley is not engaged and so idler pulley clears Belt Keeper when engaged. 2. Be sure the correct Husqvarna belt is being used. If n ...

  • Husqvarna SC18/968999352 - page 11

    11 PROBLEM ANSWER/COMMENT Belt glazed or slipping 10. Be sure the Belt Idler Assembly is adjusted correctly . See T echnical Bulletin “Inspection Procedure for Belt T ension.” 1 1. Important: Engine must be off before checking clearance of pulleys. Adjust tap bolt for 1/8” to 1/4” clearance between all pulleys, Belt Idler Pulley , Engine Pu ...

  • Husqvarna SC18/968999352 - page 12

    12 SOUND AND VIBRA TION ST A TMENT ...

  • Husqvarna SC18/968999352 - page 13

    13 This page left black intentionally ...

  • Husqvarna SC18/968999352 - page 14

    T echnical assist ance: For technical assist ance please contact your Local Dealer . ...

メーカー Husqvarna カテゴリー Brush Cutter

Husqvarna SC18/968999352のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- SC18/968999352の取扱説明書
- Husqvarnaの製品カード
- パンフレット
- またはHusqvarna SC18/968999352の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Husqvarna SC18/968999352の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Husqvarna SC18/968999352の取り付け説明書、サービスマニュアル、簡易説明書、またはHusqvarna SC18/968999352のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Husqvarna SC18/968999352の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Husqvarna SC18/968999352デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHusqvarna SC18/968999352を使用するのを助ける技術的文書のことです。説明書は通常、全てのHusqvarna SC18/968999352ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Husqvarnaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Husqvarna SC18/968999352の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHusqvarna SC18/968999352の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Husqvarna SC18/968999352に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Husqvarna SC18/968999352デバイスの基本機能を使うにあたってのヒント。 Husqvarna SC18/968999352のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Husqvarna SC18/968999352に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHusqvarna SC18/968999352のメーカー/サービスへの連絡先に関する情報。

Husqvarna SC18/968999352についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHusqvarna SC18/968999352の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHusqvarna SC18/968999352で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)