Honeywell CT87Bの取扱説明書

12ページ 0.29 mb
ダウンロード

ページに移動 of 12

Summary
  • Honeywell CT87B - page 1

    ® U.S. Registered Trademark Copyright © 2002 Honeywell All Rights Reserved 69-0274-6 Verify that you have the correct thermostat Using the compatibility chart below , verify that you purchased the correct CT87 Thermostat for your heating/cooling system. If you are unsure which model is right for your system, visit www .honeywell.com/ yourhome or ...

  • Honeywell CT87B - page 2

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 2 Prepare for installation 1. Carefully unpack your new thermostat; rough handling may affect it s accuracy . Save your receipt and identify the following parts: • CT87 Thermostat • Screws: two 1-in. sheet metal screws, two 1/2-in. binding head screws, and two 1/4-in. round head screws • W allplate (CT8 ...

  • Honeywell CT87B - page 3

    CT87A,B,J ROUND® THERMOSTAT 3 69-0274-6 5. Label the wires using the wiring labels that came with the CT87. Identify each wire using the letter of the terminal on th e old the rmo- stat (Fig. 2). Do not label the wires by color . 6. Disconnect the wires from the o ld thermostat and wrap them around a pencil to keep them from falling back into the ...

  • Honeywell CT87B - page 4

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 4 1. If using the cover ring: Position the cover ring again st the wall so that the arrow in the middle of th e cover ring is pointing up. 2. Position the wallp late or subbase . • If using cover ring : Place the wallplate/subbase over the cover ring. Rotate the wallpl ate/subbase until the wiring o penings ...

  • Honeywell CT87B - page 5

    CT87A,B,J ROUND® THERMOSTAT 5 69-0274-6 1. Place the cover ring against the outlet box so that the arrow in the middle of the cover ring is pointing up. 2. Pull the wires through the wiring hole on the bottom left side of the cover ring. 3. Align the screw slots on the cover ring with the outlet box screw holes, and attach the cover ring to the ou ...

  • Honeywell CT87B - page 6

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 6 Wire the thermostat 1. Use the wiring cross-reference table below to match each old thermostat wire with its corresponding terminal on the CT87 wallpl ate or subbase. See Fig. 8 through 13 wiring diagrams. *Never attach wires to both the B and O terminals. 2. S trip the wire insulation as needed to fit the w ...

  • Honeywell CT87B - page 7

    CT87A,B,J ROUND® THERMOSTAT 7 69-0274-6 Fig. 8. CT87A for a 2-wire heat ing only system. Fig. 9. CT87A for a 3-wire hot water heating only system . Fig. 10. CT87B for a 4-wire heat ing/cooling system . M2018 3 CT87A WALLPLATE TO SYSTEM R W Y POWER HEAT M2018 4 WIRE LABELS (LETTERS ON ORIGINAL THERMOSTAT TERMINALS) CT87A WALLPLATE 3-WIRE HOT WATER ...

  • Honeywell CT87B - page 8

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 8 Fig. 1 1. CT87B for a 5-wire heating /cooling system. Fig. 12. CT87J for a 4-wire single stage heat pump. Fig. 13. CT87J for 4-wire single stage heat pump. C O O L • O F F • H E A T F A N O N • A U T O M2022 5 HEATING POWER CT87B SUBBASE TO SYSTE M TO SYSTEM R H G R C W Y FAN HEAT COOLING POWER COOL C ...

  • Honeywell CT87B - page 9

    CT87A,B,J ROUND® THERMOSTAT 9 69-0274-6 Mount the thermostat 1. Pull off the thermostat cover and discard the red plastic insert that holds the mercury switch in place during shipping. 2. Using a pencil po int, slide the heat anticipator indicato r to 1.2 on the scale as shown in Fig. 14. IMPORT ANT : This prevents the thermostat from being damage ...

  • Honeywell CT87B - page 10

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 10 Set the heat anticipator for your system IMPORT ANT : Setting th e heat anticipator allows the thermostat to maintain accurate temperature control. 1. Using a pencil point, move the heat anticipator pointer to the numbe r that you recorded in S tep 3, su b- step 3. If you could not find the anticipator sett ...

  • Honeywell CT87B - page 11

    CT87A,B,J ROUND® THERMOSTAT 1 1 69-0274 -6 Check cooling IMPORT ANT : T o a void damaging the compressor in the air conditioner , do not operate the cooling system when the outdoor temp erature is below 50°F (10°C). 1. If your CT87 has a subbase, set the System switch on the left to Cool. IMPORT ANT : Af ter heating is teste d, wait five minutes ...

  • Honeywell CT87B - page 12

    CT87A,B,J ROUND® THERMOSTAT 69-0274-6 G .H. Rev . 08-02 www .honeywell.com/yourhome Automation and Control Solutions Honeywell Honeywell Limi ted-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. H ...

メーカー Honeywell カテゴリー Thermostat

Honeywell CT87Bのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- CT87Bの取扱説明書
- Honeywellの製品カード
- パンフレット
- またはHoneywell CT87Bの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Honeywell CT87Bの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Honeywell CT87Bの取り付け説明書、サービスマニュアル、簡易説明書、またはHoneywell CT87Bのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Honeywell CT87Bの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Honeywell CT87Bデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがHoneywell CT87Bを使用するのを助ける技術的文書のことです。説明書は通常、全てのHoneywell CT87Bユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Honeywellの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Honeywell CT87Bの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははHoneywell CT87Bの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Honeywell CT87Bに関してこのドキュメントで見つけることができる全てのヒントの目次
3. Honeywell CT87Bデバイスの基本機能を使うにあたってのヒント。 Honeywell CT87Bのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Honeywell CT87Bに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるHoneywell CT87Bのメーカー/サービスへの連絡先に関する情報。

Honeywell CT87Bについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもHoneywell CT87Bの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがHoneywell CT87Bで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)