日本語 dropdown-ico

Rosewill RC-209の取扱説明書

23ページ 2.24 mb
ダウンロード

ページに移動 of 23

Summary
  • Rosewill RC-209 - page 1

    SA T A 4 Port PCI Adaptor with RAID RC209 User Manual ...

  • Rosewill RC-209 - page 2

    Content • Feature highlights .............................................................................. • Package contents .............................................................................. • System requir ement .......................................................................... • Magic Switch introduction and jumper ...

  • Rosewill RC-209 - page 3

    1 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 SiI 3114 SA T A PCI Car d Featur e Highlights • Silicon Image SiI3114 SA T A controller chip • Compliant with PCI Specification, Rev . 2.3, 32bit, 33/66Mhz • Compliant with Serial A T A 1.0 specification • Provides four independent channels to support up to four Serial A T A drives ? ...

  • Rosewill RC-209 - page 4

    2 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Magic Switch intr oduction and jumper setting Before installing the SiI 3114 SA T A PCI Card, please see the photo below which shows all the ports & jumpers on this PCI Card. A SA T A Connector 1 (internal) B SA T A Connector 2 (internal) C SA T A Connector 3 (internal) D SA T A Connector ...

  • Rosewill RC-209 - page 5

    3 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Step by step photo installation of Magic Switch 1. Ther e are six SA T A ports in RC209 RAID adapter . W e named these ports character A thr ough F . Ports A to D ar e inter nal SA T A ports and E to F are exter nal SA T A ports. By changing the jumper setting on RC209 that allows you to utili ...

  • Rosewill RC-209 - page 6

    4 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Mode 1 (Default) - ABCD Active Mode 2 - ABDF Active Mode 3 - ABEF Active C D E F Active 2.3 close 1.2 close A B Active C D E Active F 1.2 close 1.2 close A B Active A B C D E F Active 2.3 close 2.3 close Active ...

  • Rosewill RC-209 - page 7

    5 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Mode 4 - ABCE Active Note: There ar e six SA T A ports in Serial A T A 4-Channel RAID adapter . W e named these ports character A through F . Ports A to D ar e inter nal SA T A ports and E & F ar e exter nal SA T A ports. By changing the jumper setting on the Serial A T A 4-Channel RAID ad ...

  • Rosewill RC-209 - page 8

    6 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 3. Connect one end of the Serial A T A cable to the hard disk drive. 4. Attach the other end of the Serial A T A cable to the Serial A T A controller on the Serial A T A 4-Channel RAID adapter . 5. Follow the same instructions to connect up to four hard drives. Device connection is now complet ...

  • Rosewill RC-209 - page 9

    7 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Auto configuration (recommended) The default chunk size is 64k when selecting Auto configuration . 1. As the BIOS boots press Ctrl+S or F4 when pr ompted to enter the RAID BIOS. 2. At the next screen select Cr eate RAID Set , then press Enter . ...

  • Rosewill RC-209 - page 10

    8 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 3. Select RAID0 , then press Enter . 4. Select the number of drives then press Enter . 5. Select Auto configuration , then press Enter . 6. Input the RAID size, press Enter . 7. When asked Are Y ou Sure (Y/N)?, pr ess Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are you sur e ...

  • Rosewill RC-209 - page 11

    9 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 12. Press Ctrl+E to exit the BIOS. 13. When asked Are you sur e to exit(Y/N)?, press Y to exit and r eboot. 14. Continue with FDISK and FORMA T steps as if you were installing a conventional hard drive. RAID 1 (Mirror) For New/Blank Hard Drive Recommended for all fresh HD without data. 1. As t ...

  • Rosewill RC-209 - page 12

    10 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Cr eating a SP ARE Drive This function is used when you want to backup your data by adding a new HD to RC-209. Y ou can transfer original data to the new adding HD by the following. When a hard drive failur e occurs in a mirror set, the auto-r ebuild feature enables a drive designated as SP A ...

  • Rosewill RC-209 - page 13

    11 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Auto configuration (recommended) The default chunk size is 64k when selecting Auto configuration . 1. As the BIOS boots press Ctrl+S or F4 when pr ompted to enter the RAID BIOS. 2. At the next screen select Cr eate RAID Set , then press Enter . 3. Select RAID10 , then press Enter . 4. Selec ...

  • Rosewill RC-209 - page 14

    12 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 3. Select RAID5 , then press Enter . 4. Select the number of drives then press Enter . 5. Select Auto configuration , then press Enter . 6. Input the RAID size, press Enter . 7. When asked Are Y ou Sure(Y/N)? , pr ess Y to accept. 8. Press Ctrl+E to exit the BIOS. 9. When asked Are you sur e ...

  • Rosewill RC-209 - page 15

    13 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 9. When asked Are you sur e to exit(Y/N) ?, press Y to exit and r eboot. 10. Continue with FDISK and FORMA T steps as if you were installing a conventional hard drive. Deleting RAID Arrays 1. As the BIOS boots press Ctrl+S or F4 when pr ompted to enter the RAID BIOS. 2. Select Delete RAID Set ...

  • Rosewill RC-209 - page 16

    14 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 BIOS will show up and indicate the devices attached to it. Driver Installation Quick guide: 1. If you want to add RC-209 to an existing OS, set up RC-209 into a PCI slot. Enter the OS and install RC-209 with driver disk. In this case, PC is booting up by an existing HD connecting to motherboa ...

  • Rosewill RC-209 - page 17

    15 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Choose the correct OS for your futur e system. Then choose “Standard PC with C-Step i486”. ...

  • Rosewill RC-209 - page 18

    16 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 Keep the floppy disk in floppy drive. PC will notice you as below if you take them off from the drive. The installation of RC-209 by floppy drive will be completed and the system will detect the HD which now plug on the card. ...

  • Rosewill RC-209 - page 19

    17 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 After you install RC-209 successfully by floppy disk, installation will lead you back to the same screen as below and then pr ess “enter” to left the setting. f. Once the system can find the HD connecting to RC-209, you can follow the normal steps to complete the Windows installation. 3 ...

  • Rosewill RC-209 - page 20

    18 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 For New Installation A new installation requir es a floppy disk for the driver installation. T o make this floppy disk, copy the contents of the “RC-209DriverRAID” folder , found on the driver CD, onto a blank floppy disk then follow the directions below . 1. Setup the RAID Array pri ...

  • Rosewill RC-209 - page 21

    19 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 6. Insert the floppy disk, then press Enter . 7. Select Silicon Image SiI 3114 SoftRaid 5 Controller for Windows 2000 , then pr ess Enter . 8. Press Enter again to finish driver installation, then follow the on-scr een instructions to complete the Windows installation. For An Existing Insta ...

  • Rosewill RC-209 - page 22

    20 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 file’ s location. Press Next to continue to setup. (Change D : to match your CD-ROM drive letter) 9. Click Next again, then Finish . 10. Remove the driver CD, close all open Windows, then restart Windows to complete the installation. For An Existing Installation 1. Setup the RAID Array pri ...

  • Rosewill RC-209 - page 23

    21 User Manual SA T A 4 Port PCI Adaptor with RAID RC209 3. Click Finish . 4. Remove the driver CD, close all open Windows, then restart Windows to complete the installation. T o V erify Windows® 98SE/Me Installation 1. Right click My Computer , click Properties , then click Device Manager . 2. Double click SCSI Controllers, Silicon Image SiI 3114 ...

メーカー Rosewill カテゴリー Network Card

Rosewill RC-209のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- RC-209の取扱説明書
- Rosewillの製品カード
- パンフレット
- またはRosewill RC-209の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Rosewill RC-209の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Rosewill RC-209の取り付け説明書、サービスマニュアル、簡易説明書、またはRosewill RC-209のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Rosewill RC-209の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Rosewill RC-209デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがRosewill RC-209を使用するのを助ける技術的文書のことです。説明書は通常、全てのRosewill RC-209ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Rosewillの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Rosewill RC-209の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははRosewill RC-209の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Rosewill RC-209に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Rosewill RC-209デバイスの基本機能を使うにあたってのヒント。 Rosewill RC-209のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Rosewill RC-209に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるRosewill RC-209のメーカー/サービスへの連絡先に関する情報。

Rosewill RC-209についてご質問がありますか？

次のフォームを使用してください

見つけた説明書を読んでもRosewill RC-209の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがRosewill RC-209で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

Captcha
新しい画像

コメント (0)