ページに移動 of 77
Owner ’ s Manual Multimedia Projector MODEL PLC-XK2200 PLC-XK2600 Network Supported Wired LAN Refer to the Owner's Manuals below for details about network function. Network Set-up and Operation ...
2 Features and Design This Multimedia Projector is designed with the most advanced technology for portability , durability , and ease of use. This projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology . This projector i ...
3 Each name of corporations or products in this book is either a registered trademark or a trademark of its respective corporation. Features and Design . . . . . . . . . . . . . . 2 ................. 3 ...
4 ...
5 All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cle ...
6 Openings in the cabinet are provided for ventilation. T o ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. Hot air is exhausted from the exhaust vent. When using or installing the projector , t ...
7 Compliance Federal Communications Commission Notice Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against ha rmf ul i nte rf er en ce in a r es id en ti al in sta ll at io n. T hi s e qu ip men ...
8 Part Names and Functions Back ① ② ③ ④ Speaker ⑤ ⑥ Projection Lens ⑦ Lens Cap (See page 60 for attaching.) ⑧ ? ...
9 ⑦ (MIC)- Part Names and Functions ② ③ ① ⑥ ⑤ ⑧ ④ ④ Connect the composite video output signal to this jack (p.15). ② Connect output signal ...
10 Part Names and Functions ⑦ Lights yellow when the projection lamp reaches its end of life (pp.61, 69). ⑧ – Lights red when the projector detects an abnormal condition. – Blinks red whe ...
1 1 T o ensure safe operation, please observe the following precautions: – Do not bend, drop or expose the remote control to moisture or heat. – For cleaning, use a soft dry cloth. Do not apply benzene, thinner , spray , or any chemical material. ⑦ ⑭ ⑩ ⑳ ④ ⑱ ② ⑧ ⑨ ...
12 Part Names and Functions T o ensure safe operation, please observe the following precautions : ? ...
13 For projector positioning, see the figures below . The projector should be set perpendicularly to the plane of the screen. • The brightness in the room has a great influence on picture quality . It is recommended ...
14 Connecting to a Computer Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables. • When the MIC function is set to in the Sound menu, the MIC function is disabled. •When is set to On in Sound Menu, AUDIO IN (PC/MIC) and AUDIO IN(L/R) terminals ...
15 (MIC)- External Audio Equipment Audio cable (stereo) S-video cable Audio Output S-video Output Audio Input AUDIO IN (PC or MIC) S-video- VGA cable Video cable COMPUTER IN 1 / S-VIDEO IN /COMPONENT IN VIDEO IN Audio cable (stereo) AUDIO OUT (stereo) AUDIO IN A ...
16 (MIC)- External Audio Equipment AUDIO IN Audio cable (stereo) Audio Input Component Video Output (Y , Pb/Cb, Pr/Cr) Audio Output RGB Scart 21- pin Output Scart- VGA cable Component- ...
17 This projector uses nominal input voltages of 100-240 V AC and it automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor . T o reduce the risk of electrical shock, do not plug ...
18 The preparation display will disappear after 30 seconds. (See page 52 for Lamp control status.) Connect the projector ’s AC power cord into an AC outlet. The POWER indicator lights red. Open the Open the Open the lens cap. Press the ON/ST AND-BY button on the top control ...
19 Basic Operation PIN (Personal Identification Number) code is a security code that allows the person who knows it to operate the projector . Setting a PIN code prevents unauthorized use of the projector . A PIN code consists of a four-digit number . Refer to the PIN code lock function in the Set ...
20 OFF ...
21 The projector can be adjusted or set via the On-Screen Menu. The menus have a hierarchical structure, with a main menu that is divided into submenus, which are further divided into other submenus. For each adjustment and setting procedure, refer t ...
22 Basic Operation Menu Bar For detailed functions of each menu, see “Menu T ree” on pages 67-68. Main Menu Sub-Menu ③ Used to select an image mode from among , Standard , , , ? ...
23 Basic Operation Rotate the Zoom Ring to zoom in and out. Rotate the Focus Ring to adjust the focus of the image. If a projected picture still has keystone distortion after pressing the AUTO SETUP button on the top control or the AUTO SET button on the remote control, co ...
24 Basic Operation 1 2 Press the MENU button to display the On-Screen Menu. Use the Point buttons to select Sound . Press the Point or the SELECT button to access the submenu items. Press the VOLUME+/– buttons on the top control or on the remote control to adjust the volume. The volume ...
25 Basic Operation Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons enables you to make the desired operation quickly without calling up the On-Screen Menu. Press the COMPUTER 1/2, VIDEO, S-VIDEO and COMPONENT buttons ...
26 Basic Operation Press the P-TIMER button on the remote control to operate the Count up/Count down function. Refer to p.50 for detail of Setting for the P-timer function. T o stop the count time, press the P-TIMER button. T o cancel the P-timer function, press and hold the P- TIMER button. ? ...
27 Choose either or by pressing the COMPUTER 1 or COMPUTER 2 button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below . 1 2 3 ? ...
28 This projector automatically tunes to various types of computers with its Multi-scan system and Aut ...
29 Auto PC Adjustment function is provided to automatically adjust , , and V ertical positions to conform to your computer . PC adjust Menu ? ...
30 PC adjust Menu Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector . Manual PC Adjustment enables you to precisely adjust several parameters to ...
31 Store T o store the adjusted data, select Store and then press to one of the Modes 1 to 10 in which you want to store, and then press the SELECT ...
32 ? ...
33 Press the MENU button to display the On-Screen ? ...
34 This projector has the picture screen resize function, which enables you to customize the image size. Screen Menu Provide the image to fit the screen size. Normal Provide the imag ...
35 Select . The On-Screen Menu disappears and appears. Press the SELECT button to expand the image size. Use the buttons to pan the image. The Panning function can work only when the image is larger than t ...
36 Choose Video or S-video by pressing the VIDEO or the S-VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below . 1 2 Video ? ...
37 Choose or by pressing the COMPONENT or the COMPUTER 1 button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below ...
38 1 2 If the projector cannot reproduce proper video image, select a specific broadcast signal format ...
39 ...
40 1 2 Press the Point button to decrease the contrast; press the Point button to increase the contrast (from 0 to 63). Press the Point button to decrease the brightness; press the Point button to increase the brightness (from 0 to 63). Contrast Press t ...
41 An interlaced video signal can be displayed in progressive mode. Select one of the following options. ......... Disabled. L 1 ......... For an active picture. L 2 ......... For a still picture. Film ....... ? ...
42 This projector has the picture screen resize function, which enables you to customize the image size. Normal Screen Menu 1 2 Provide the image to fit the screen size while maintaining the aspect ratio of the input signal. Custom adj. • When no signal is det ...
43 This function is used to adjust keystone distortion of the projected image. Use the Point buttons to choose the item you want to adjust. T o correct keystone distortion, press the SELECT button. Keystone appears on the screen. Use the Point buttons to correct keystone distortion (p. ...
44 Setting Setting Setting Menu Press the MENU button to display the On-Screen Menu. Press the Point buttons to select Setting and press the Point or the SELECT button to access the submenu items. 1 2 Use the Point buttons to select the desired item and then press the Point or the SELECT button to access the selected item. Thi ...
45 • Du ring i s in pr ogr ess, I f the M ENU button or the ON/ST AND-BY button is pressed, will stop. If the COMPUTER 1/2 button or VIDEO or COMPONENT or S-VIDEO or VIDEO or COMPONENT or S-VIDEO VIDEO or COMPONENT or S-VIDEO button is pressed, ? ...
46 Setting This function decides whether to display On-Screen Displays. On ............................ Show all the On-Screen displays. Use this function when you want to project images after the lamp becomes bright enough. The factory default setting is in this option. ....... Show the input image instead o ...
47 Setting Capture Capture This function enables you to capture an image being projected to use it for a starting-up display or interval of presentations. Select Capture and press the SELECT button. A confirmation box appears and select to capture the projected image. After capturing the projected image, go to the Logo select function an ...
48 Use the Point buttons to enter a number . Press the Point buttons to fix the number and move the red frame pointer to the next box. The number changes to . If you fixed an incorrect number , use the Point buttons to move the pointer to the number you want to ...
49 The COMPUTER IN 2/MONITOR OUT terminal on the back of the projector is switchable for computer input or monitor output. (See page 9) Select Computer 2 or Monitor Out with the Point buttons. Computer 2 . . computer input Monitor Out . . monitor out T erminal function is not available when selecting Computer 2 to t ...
50 This function is available when operating the projector via network. Network .... Supply the power to the network function even after turning off the projector by pressing the ON/ST AND-BY button on the remote control. Y ou can turn on/off the projector via network, modify network environment, and receive an ...
51 Closed Caption Closed Caption Closed Caption is a printed version of the program sound or other information displayed on the screen. If the input signal contains closed captions, you can turn on the feature and switch the channels. Press the Point the Point buttons to select , CC1 ...
52 This projector provides two different remote control codes: the factory-set initial code ( Code 1 ) and the secondary code ( Code 2 ). This switching function prevents remote control interference when operating several projectors or video equipment at the same time. W h e n o p e r a t i n g t h e p r o ...
53 Setting This function locks the top control and remote control buttons to prevent operation by unauthorized persons. Select ...
54 Use the Point buttons to select , On 1 or On 2 , and then press the SELECT button to make a choice. Use the Point buttons to enter a number . Press the Point buttons to ...
55 Setting This function provides the following options in the cooling fans’ operation when the projector is turned off (p.20). L 1 ..... Normal operation L 2 ..... Slower, lower-sound and longish-time than the normal operation ( L 1 ). Fan Choose the running speed of cooling fans from the following options according to the ground elevation under ...
56 This function returns all setting values except for the , , , Lamp counter and Filter counter to the factory default settings. W arn ...
57 Setting The Information Menu is used for checking the status of the image signal being projected and the operation of the projector . Lamp co ...
58 Maintenance and Cleaning The W ARNING indicator shows the state of the function which protects the projector. Check the state of the W ARNING indicator and the POWER indicator to take proper maintenance. ...
59 Maintenance and Cleaning Filter prevents dust from accumulating on the optical elements inside the projector . Should the Filter become clogged with dust particles, it will reduce cooling fans’ ef fectiveness and may result in internal heat buildup and adversely affect the life of the projector . If a “Filter warning” icon appears on the s ...
60 Maintenance and Cleaning Unplug the AC power cord before cleaning. Gently wipe the projection lens with a cleaning cloth that contains a small amount of non-abrasive camer ...
61 Maintenance and Cleaning When the projection lamp of the projector reaches its end of life, the Lamp replacement icon appears on the screen and LAMP REPLACE indicator lights yellow . Replace the lamp with a new one promptly . The timing when the LAMP REPLACE indicator should light is depending on the lamp mode. Follow these steps to replace the ...
62 Maintenance and Cleaning This projector uses a high-pressure lamp which must be handled carefully and properly . Improper handling may result in accidents, injury , or create a fire hazard. ? ...
63 – Solutions No power – Plug the power cord of the projector into the AC outlet. – See if the POWER indicator lights red. – Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. See page 18. ...
64 No image – Check the connection between your computer or video equipment and the projector . See pages 14-16. – See if the input signal is correctly output from your computer . Some laptop computers may need to change the setting for monitor output when connecting to a projector . See your computer ’s instruction m ...
65 – Check PC adjust menu or Screen menu and adjust them. See pages 30-31, 34-35. – PIN code lock is being set. Enter a PI ...
66 If problems still persist after following all operating instr ...
67 V olume Mute On/Off Sound 0-63 RGB Component S-video RGB RGB (Scart) Video Computer 1 Computer 2 MIC On/Off MIC gain 0-63 Standby MIC out On/Of f Dynamic Cinema Blackboard (Green) Image 1 ? ...
68 Auto P AL SECAM NTSC NTSC 4.43 P AL-M P AL-N Auto 1080i 1035i 720p 575p 480p 575i 480i 0–63 0–63 Off (2) (3) Contrast Brightness Color Tint Red Green Blue Sharpness Reset Store Gamma Progressive 0–63 0–63 0–63 0–15 0–1 ...
69 Check the indicators for projector condition. • • • green. • • • red • • • off • • • blinks green. When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow . When this indicator lights yellow , replace the projection lamp with a new one promptly . (pp. 55, 61) The projector is off. (T ...
70 Basically this projector can accept the signal from all computers with the V -, H-Frequency mentioned below and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited. ? ...
71 Projector T ype Multi-media Projector Dimensions (W x H x D) 13.13" x 3.98" x 9.72" ( 333.5mm x 101.0mm x 247.0mm) (Not including protrusions) Net W eight 6.4 lbs ...
72 Model No. POA-CA-COMPVGA POA-CA-VGAS POA-CA-SCART KA-MC-DB10 ? ...
73 This projector is compliant with PJLink Standard Class 1 of JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see the owner ’s manual of “Network S ...
74 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 ? ...
75 Write down the PIN code number in the column below and keep it with this manual securely . If you forgot or lost the number and unable to operate the projector , contact the service center . Factory default set No: 1 2 3 4 * Factory default set No: 4 3 2 1 * Pu ...
76 Dimensions Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.47) 79.6(3.13) 46.2(1.82) 3.7(0.15) 17.1(0.67) 33.6(1.32) 35.9(1.41) 85.4(3.36) 83.8(3.30) 10.0˚ 247.0(9.72) 4.6(0.18) 80.2(3.16) 138.0(5.43) 122.2(4.81) 1 14.0(4.49) 137.3(5.41) 96.7(3.81) 333.5(13.13) 67.3(2.65) 99.5(3.92) 31.7(1.25) 64.6( ...
KS8AE ...
Sanyo PLC-XK2600のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- PLC-XK2600の取扱説明書
- Sanyoの製品カード
- パンフレット
- またはSanyo PLC-XK2600の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Sanyo PLC-XK2600の取扱説明書に含まれています。
取扱説明書と呼ばれる文書のグループは、Sanyo PLC-XK2600の取り付け説明書、サービスマニュアル、簡易説明書、またはSanyo PLC-XK2600のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Sanyo PLC-XK2600の製品を使用するにあたって最も人気のある説明書を閲覧できます。
Sanyo PLC-XK2600デバイスの取扱説明書はどのようなものですか？
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがSanyo PLC-XK2600を使用するのを助ける技術的文書のことです。説明書は通常、全てのSanyo PLC-XK2600ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。
Sanyoの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。
1. Sanyo PLC-XK2600の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははSanyo PLC-XK2600の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Sanyo PLC-XK2600に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Sanyo PLC-XK2600デバイスの基本機能を使うにあたってのヒント。 Sanyo PLC-XK2600のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Sanyo PLC-XK2600に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるSanyo PLC-XK2600のメーカー/サービスへの連絡先に関する情報。
Sanyo PLC-XK2600についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもSanyo PLC-XK2600の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSanyo PLC-XK2600で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。