-
Porter-Cable PN650 - page 1
Instruction manual The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ IMPORTANT Please make certain tha ...
-
Porter-Cable PN650 - page 2
2 Date of Manufacture: ___________________________ Fecha de fabricación:, Date de fabrication: Serial No: ______________________________________ Número de serie:, Nombre d'ordre ...
-
Porter-Cable PN650 - page 3
3 GENERAL SAFETY RULES DANGER: When using pneumatic tools, basic safety precautions should always be followed to reduce the risk of personal injury, including the following: READ AND FOLLOW ALL INSTRUCTIONS. There are certain applications for which this tool was designed. Porter-Cable strongly recommends that this tool NOT be modified and/or used f ...
-
Porter-Cable PN650 - page 4
4 9. Use clean, dry, regulated, compressed air at 50 to 120 PSI, (3.4 to 8.3 BAR). Fig. 6. 10. Connect tool to air supply hose with a coupling that automatically removes all pressure from the tool when the coupling is disconnected. Fig. 7. 11. Disconnect tool from air supply hose before doing tool maintenance, clearing a jammed fastener, leaving wo ...
-
Porter-Cable PN650 - page 5
5 EMPLOYER’S RESPONSIBILITIES DANGER: Employer must enforce compliance with the safety warnings and all other instructions contained in this manual. Keep this manual available for use by all people assigned to use this tool. For personal safety and proper operation of this tool, read and understand tool labels and manual. Failure to follow warnin ...
-
Porter-Cable PN650 - page 6
6 DANGER: All air line components (hoses, connectors, filters, regulators, etc.) must have a minimum working pressure rating of at least 150 PSI (10.3 BAR) or 150% of maximum system potential, whichever is greater . Do not connect tool to pressure which potentially exceeds 200 PSI (13.7 BAR). Only connect tool to air supply hose with a coupling tha ...
-
Porter-Cable PN650 - page 7
7 FINISH NAIL GUIDE ASSEMBL Y 1. WARNING: Disconnect tool from air supply. 2. The finish nail guide (A) Fig. 17, for driving 1- 1 / 4 "(3d) to 2- 1 / 2 "(8d) finish nails, is provided with a rubber nose cushion (B) Fig. 17 that will reduce marring of the work surface. Assembly of the finish nail guide requires the use of the magnetic nail ...
-
Porter-Cable PN650 - page 8
8 HAMMER ASSEMBL Y 1. WARNING: Disconnect tool from air supply. 2. To install hammer attachments (A through D) Fig. 21 lay tool on its cap with nail guide pointing upward. Loosen and remove the magnetic nail guide and bushing (Fig. 15) using the 24mm open end wrench supplied. Remove the spring (C) Fig. 22, driver guide (F), three wave washers (D), ...
-
Porter-Cable PN650 - page 9
9 8. Align flats on hammer base with the slots in the hammer head guide bushing until the 30mm open end wrench will engage the flats (A) Fig. 27. 9. Engage the other 30mm open end wrench with the flats on hammer head as shown (B) Fig. 27 and tighten as securely as possible. PREP ARING THE TOOL 1. After reading and understanding this entire manual, ...
-
Porter-Cable PN650 - page 10
10 1. Attach appropriate nail guide or hammer attachment. 2 . Orient nail (A) Fig. 29 with point down and and insert into the nail guide (B). 3. Position point of nail (A) Fig. 30 in the desired location and push down on the tool. The tool will began cycling and driving the fastener. NOTE: Be sure to maintain constant hand pressure in line with the ...
-
Porter-Cable PN650 - page 11
11 CABLE/DELTA FACTORY SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies. Should you have any questions about your tool, feel free to write us at any time. In any communications, please give your tool m ...
-
Porter-Cable PN650 - page 12
PORTER-CABLE LIMITED ONE YEAR WARRANTY Porter-Cable warrants its nailing and stapling tools for a period of one year from the date of original purchase. We will repair or replace at our option, any part or parts of the product and accessories covered under this warranty which, after examination, proves to be defective in workmanship or material dur ...
-
Porter-Cable PN650 - page 13
The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont des marques de fabriquant de la PORTER-CABLE • DELTA): BAMMER ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER-CABLE ® , QUICKSAND ® , SANDTRAP ® , S ...
Porter-Cable PN650についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもPorter-Cable PN650の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがPorter-Cable PN650で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。