-
Silva TH52 - page 1
Installation Manual English Depth transducer TH 52 performance by NEXUS NETWORK ...
-
Silva TH52 - page 2
DEPTH TH52 English 11-1 ...
-
Silva TH52 - page 3
English DEPTH TH52 11-2 ...
-
Silva TH52 - page 4
DEPTH TH52 English 11-3 CONTENTS: 1 A pplicat ions ......................................................................................................... 4 2 Tools and Materials Needed ............................................................................... 4 3 Mounting Location ............................................................ ...
-
Silva TH52 - page 5
English DEPTH TH52 11-4 INSTALLATION INSTRUCTIONS Thru-Hull Depth Transducer Low Profile, Flush, and Retractable Models WA RNING: NEVER USE SOLVENTS! Certain cleaners, fuel, paints, sealants, and other products may contain strong solvents, such as acetone, which attack many pl astics greatly reducing their strength. 1 Applications • Plastic housi ...
-
Silva TH52 - page 6
DEPTH TH52 English 11-5 3 Mounting Location 3.1 Acoustic Noise Acoustic noise is alway s present and t hese sound w aves can interfere w ith the operation of the transducer. Background noise from sources such as: waves, fish, and other vessels cannot be controlled. Howeve r, carefully selecting the transducer mounting location can minimize the affe ...
-
Silva TH52 - page 7
English DEPTH TH52 11-6 3.3 Boat Types (see Figure 1) • Displacement hull pow erboat —Locate 1/3 aft LWL and 150–300mm (6–12") off the centerline on the side of the hull where the propeller is moving dow nward. • Planing hull powerboat —Mount well aft, on or near the centerline, and w ell inboard of the first set of lifting strakes ...
-
Silva TH52 - page 8
DEPTH TH52 English 11-7 4 Installation Cored fiberglass hul l—Follow separate inst ructions on page 4. 4.1 Hole Drilling Warnin g: Always wear safety goggles and a dust mask. 1. Drill a 3 mm or 1/8" pilot hole from inside t he hull. If there is a rib, strut, or other hull irregularity near the selected mounting location, dr ill from the outs ...
-
Silva TH52 - page 9
English DEPTH TH52 11-8 4.2 Bedding Caution : Never pull, carry, or hold the transducer by its cable; this may sever internal connections. 1. Remove the hull nut and any w asher (see Figure 2). Also remove the cap nut and the transducer insert. 2. Apply a 2mm (1/16") thick layer of sealant around the lip of the housing that contacts the hull a ...
-
Silva TH52 - page 10
DEPTH TH52 English 11-9 tighten only. Do not over tighten. Warnin g: Always attach the safety wire to prevent the insert from backing out in the unlikely event that the cap nut fails or is screwed on incorrectly. 6. Attach the safety w ire. Attach the sa fety wire to one ey e in the hull nut. Lead the wire in a counterclockw ise direction and threa ...
-
Silva TH52 - page 11
English DEPTH TH52 11-10 5.3 Installation in a Cored Fiberglass Hull The core (wood or foam) must be cut and sealed carefully . The core must be protected from water seepage, and the hull m ust be reinforced to prevent it from crushing under the hull nut allowing the housing to become loose. Warnin g: Always wear safety goggles and a dust mask. 1. ...
-
Silva TH52 - page 12
DEPTH TH52 English 11-11 6 CONNECTION TO INSTRUMENT/CONTACTS The depth transducer connects to t he FI-30 Server or directly. The transducer cable is clearly marked w i th No 2 and the colours w ill correspond to input screw terminal on the Server. IMPORTANT! DO NOT CUT OR EXTEND THE 8 M TRANSDUCER CABLE! 7 Calibration Calibration is carried out in ...
-
Silva TH52 - page 13
English DEPTH TH52 11-12 9 TECHNICAL DATA Dimensions Transduc er: 51 x 86 mm (1 5/8” x 3 3/8”) Transducer cable: 8 m (9.9 ft + 26.2 ft) Power supply: 12V DC (10-16V) Power consumption: 0.2 W Depth range: 0.8 - 150 m (3 - 450 ft) at speed up to 30 knots. Accuracy: ± 0.1 % Type of transducer: Piezocrystal 200 kHz Temperature range: Operation -10 ...
-
Silva TH52 - page 14
DEPTH TH52 English 11-13 ...
-
Silva TH52 - page 15
English DEPTH TH52 11-14 ...
-
Silva TH52 - page 16
DEPTH TH52 English 11-15 Copyright ©: Silva Sweden AB Kuskvägen 4, 191 62 Sollentuna, Sweden Tel: +46 -(0) 8 - 623 43 00. Fax: +46 -(0) 8 - 92 76 01 www.s il va .s e 22418-1 Edition 1 ...
Silva TH52についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSilva TH52の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSilva TH52で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。