-
Salton JM1A - page 1
LIMITED ONE YEAR WARRANTY W arranty: This Juiceman® product is warranted by Salton, Inc. to be free from defects in materials or workmanship for a period of (1) year from the original purchase date. This product warranty covers only the original consumer purchaser of the product. W arranty Coverage: This warranty is void if the product has been da ...
-
Salton JM1A - page 2
14 NOTES IMPOR T ANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions. 2. T o protect against risk of electrical shock do not put cord, plugs, or appliance in water or other liquid. 3. Close supervision is necessary when any appliance is used by or near ...
-
Salton JM1A - page 3
TROUBLESHOOTING (Continued) Possible Correction Improper fit between the Blade Basket and Hub can cause parts of the Juice Bowl to rub against the Blade Basket. If this is the case, call Consumer Service at (800) 233-9054. Certain produce (pineapples and overripe produce) may build up on Blade Basket, causing pulp to eject before juice is completel ...
-
Salton JM1A - page 4
TROUBLESHOOTING Possible Correction T ry juicing slower, as wet produce is more likely to build up in Cover . To release pulp, lightly tap on the side of the Cover . Empty Pulp Basket if full. Blade Basket may not have been seated correctly , causing it to become unseated during use. Should this be the case, check the gear teeth of the Blade Basket ...
-
Salton JM1A - page 5
® 11 CLEANING YOUR JUICER (Continued) After cleaning and reassembly is complete, your new Juicer is ready to go to work! Before starting, make sure the Blade Basket is securely seated and the Pulp Basket is at the rear of the Juicer to receive pulp. The pulp from your Juicer can be used in many different applications such as breads, muffins, cakes ...
-
Salton JM1A - page 6
Clean Y our Juicer Thoroughly Before Retiring For The Day PLEASE NOTE: CLEANING YOUR JUICER 10 • Unplug from outlet before assembling or removing parts and before cleaning. Do not immerse the Motor Base in water or spray it with water . Clean only by wiping with a damp sponge, cloth, or paper towel. Use any liquid dishwashing detergent but do not ...
-
Salton JM1A - page 7
9 ASSEMBL Y INSTRUCTIONS (Continued) Step Four Place the Juicer Cover on over the Juice Bowl with the large pulp ejection opening towards the back of the Juicer . Swing the Clamps upward as shown in the illustration. Step Five Place the tops of the Clamps on the respective slots on the Juicer Cover , leaving the Clamp Hinges resting out. Press the ...
-
Salton JM1A - page 8
8 Step One Place Juice Bowl on top of the Motor Base. The Juice Spout fits over the front of the Juicer . T wo tabs located on the underside of the Juice Bowl should rest in the two complimentary slots on top of the Motor Base. The tabs and slots are located by each Clamp. See illustration. Step T wo Set the Blade Basket on the Motor Hub in the cen ...
-
Salton JM1A - page 9
8 Step One Place Juice Bowl on top of the Motor Base. The Juice Spout fits over the front of the Juicer . T wo tabs located on the underside of the Juice Bowl should rest in the two complimentary slots on top of the Motor Base. The tabs and slots are located by each Clamp. See illustration. Step T wo Set the Blade Basket on the Motor Hub in the cen ...
-
Salton JM1A - page 10
9 ASSEMBL Y INSTRUCTIONS (Continued) Step Four Place the Juicer Cover on over the Juice Bowl with the large pulp ejection opening towards the back of the Juicer . Swing the Clamps upward as shown in the illustration. Step Five Place the tops of the Clamps on the respective slots on the Juicer Cover , leaving the Clamp Hinges resting out. Press the ...
-
Salton JM1A - page 11
Clean Y our Juicer Thoroughly Before Retiring For The Day PLEASE NOTE: CLEANING YOUR JUICER 10 • Unplug from outlet before assembling or removing parts and before cleaning. Do not immerse the Motor Base in water or spray it with water . Clean only by wiping with a damp sponge, cloth, or paper towel. Use any liquid dishwashing detergent but do not ...
-
Salton JM1A - page 12
® 11 CLEANING YOUR JUICER (Continued) After cleaning and reassembly is complete, your new Juicer is ready to go to work! Before starting, make sure the Blade Basket is securely seated and the Pulp Basket is at the rear of the Juicer to receive pulp. The pulp from your Juicer can be used in many different applications such as breads, muffins, cakes ...
-
Salton JM1A - page 13
TROUBLESHOOTING Possible Correction T ry juicing slower, as wet produce is more likely to build up in Cover . To release pulp, lightly tap on the side of the Cover . Empty Pulp Basket if full. Blade Basket may not have been seated correctly , causing it to become unseated during use. Should this be the case, check the gear teeth of the Blade Basket ...
-
Salton JM1A - page 14
TROUBLESHOOTING (Continued) Possible Correction Improper fit between the Blade Basket and Hub can cause parts of the Juice Bowl to rub against the Blade Basket. If this is the case, call Consumer Service at (800) 233-9054. Certain produce (pineapples and overripe produce) may build up on Blade Basket, causing pulp to eject before juice is completel ...
-
Salton JM1A - page 15
14 NOTES IMPOR T ANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. Read all instructions. 2. T o protect against risk of electrical shock do not put cord, plugs, or appliance in water or other liquid. 3. Close supervision is necessary when any appliance is used by or near ...
-
Salton JM1A - page 16
LIMITED ONE YEAR WARRANTY W arranty: This Juiceman® product is warranted by Salton, Inc. to be free from defects in materials or workmanship for a period of (1) year from the original purchase date. This product warranty covers only the original consumer purchaser of the product. W arranty Coverage: This warranty is void if the product has been da ...
Salton JM1Aについてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSalton JM1Aの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSalton JM1Aで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。