M&S Systems WG100Wの取扱説明書

24ページ 2.66 mb
ダウンロード

ページに移動 of 24

Summary
  • M&S Systems WG100W - page 1

    In-W all & Ceiling Speakers Ow ner ’ s Ma nual Part Numbers WG100C WG 10 0 W WG150C WG150W WG Series 115986D.pdf 1 115986D.pdf 1 11/16/2005 10:54:34 AM 11/16/2005 10:54:34 AM ...

  • M&S Systems WG100W - page 2

    Page 2 Introduction W G Series ceiling a nd in-wall spe akers are des igned to pro vide clear, sharp ly-focuse d audio reproduc tion while rem aining unobt rusive i n the back ground. Th ese speakers bring out t he best in any home theat er or whole-hous e stereo s ystem. These prod ucts als o offer many features, i ncluding: • 1” Asymmetrical ...

  • M&S Systems WG100W - page 3

    Page 3 W G150C C eiling Speakers (Sold in Pairs) W G100 W I n-wall Speakers (Sol d in Pairs) Page 3 Frequenc y R esponse 35Hz to 20kHz (+/-3db) Maximum Po wer Rating 150 W atts Impedance Rating 8-Ohms Overall Dim ensions 10 7/8” Diameter Specificatio ns 8” Kevlar cone woofer; 1” asymmetrical al uminum dome tw eeter Mounting Dimen sion w/o Mou ...

  • M&S Systems WG100W - page 4

    W G150 W I n-wall Speakers (Sol d in Pairs) Unpacking Y our Speakers Before you unpack your speakers, be e xtra care f ul not to touch the cone a nd twe eter materials. After carefully unpacking y our speakers, the carton and the pack ing mate rial should be s aved for possible use lat er. If any speaker appears to be damaged, do no t attempt to re ...

  • M&S Systems WG100W - page 5

    foot ceilings and abov e) apart but no clos er than 2 feet to any adjacent wall. Avoid placing speake rs in air retur n cavitie s. Some ty pe of protection will be required for the back of the speaker if blown insulation is used . The following is a partial list o f way s to protect the speaker: • Use an RE-16 speaker cover • Use a piece of woo ...

  • M&S Systems WG100W - page 6

    of the speaker, use a piece of bat insulation at least 3 inches thick in the stud cavity. Th is insulation should not h ave a backing or if i t does, the backing must be installed facing away f rom the speaker. The insulation should extend about 2 ft. on either side of the speaker opening. Do not install speakers in outside walls, stud cavities con ...

  • M&S Systems WG100W - page 7

    TIPS FOR NEW CONSTRUCTION • If poss ible, run speaker wires a f ter AC wiring is in place to avoid additional noise caused by close proximit y of wiring. • Secure the speaker wires against a joist with insulated staples, being care f ul not to pierce the wire insulation. Allow slack for building material expansion. • Horizontal wire runs sh o ...

  • M&S Systems WG100W - page 8

    installed. Leave a t least 18 inche s additional ca- ble for the connection during final speaker instal- lation. Run the o ther end of the speaker c able to the audio source. NOTE: Make a draw ing of each speaker location. This wil l a ssist y ou in lo cat ing the wi res i f they have been covered a fter the wall board has been installed. Step 3. T ...

  • M&S Systems WG100W - page 9

    tweeter when r emoving t he paint mask in order to prevent any damage. Atta ch th e speaker cable to t he speaker by pressing down on the red (+) or black (-) gold-plated push terminals and inserting the red wire in the red terminal and the black wire in t he black terminal. See Figure 3 . Make su re that none of the s trands from the black and red ...

  • M&S Systems WG100W - page 10

    highest directional response in this direction. See figure 5. If you want to disperse the sound in a 360- degree pattern yo u m u s t position the line in the tw eeter in a horizo ntal position. See figure 6. The combination of switch settings allow y ou to boost and cut bass and treble +/-3dB. Adjust the speaker level to accommodate for room acous ...

  • M&S Systems WG100W - page 11

    In-wall Speakers Step 1. Speaker mounting rings are used in the pre-construction phase o f speaker installation during construction of new homes and additions. W G Serie s mounting rin gs are designed to provide drywall installers the correct cut-out pattern for t he speakers. The rings have “flaps” that are nailed/screwed/stapled o nto the stu ...

  • M&S Systems WG100W - page 12

    • Do not install the actual speaker until the wall board is in place. Until then leave several feet of wire secured to the back o f the mounting ring. The exces s wire can be re moved during final installation. During the drywall installation, make sure the speaker cut-out hole does not extend farther than 1/4 inch from the inside of the mounting ...

  • M&S Systems WG100W - page 13

    Step 3. This is the f inish-out stage. Prepare t he speaker wiring by stripping off approximately 3 inches of the ou ter jacket (care should be ta ken so the insulation on the wires inside the jacket are not damaged) also strip approximately 3/8 inch off the end s of th e two inside condu ctors. Twist the ends of the stranded cable so the wires are ...

  • M&S Systems WG100W - page 14

    Page 14 the baffle using the 6 screws provided. DO NOT OVERTIGHTEN THE SCREW S, the screws should on only be tight enough to secure the speaker. Step 6. After the spea k er is moun ted, adjustments to the s wiv el tweeter (small speaker) can be made b y either directing the so und visually or by using a musical source to determine the best sound co ...

  • M&S Systems WG100W - page 15

    Page 15 Step 7. Divide e ach adhesive bead strip in half. (Adhesive bead strips are in the clear self -closing bag). Place strips on the edge of the grille as shown in figure 14. Reinsta ll the g rill on the speaker. Step 8. Adhere the WG Se ri es l og o t o the grille with the pressu re sen s itiv e tape. Repeat the steps for the second speaker. S ...

  • M&S Systems WG100W - page 16

    Page 16 for Existing Construction Ceiling Speakers For existing construction, the use of mounting rings can not o ccur. The f ollowing steps out line how to locate a section b etween two joists, mark the outer boundaries of the hole, drill a small h ole in the center to verify the location and then cut the main hole. Step 1. Dete rm i ne t he lo ca ...

  • M&S Systems WG100W - page 17

    Page 17 deep enough to fully penetrate the drywall. Step 4. Obta in a leng th of st if f wi re s uch as a straightened wire coat hanger. Bend it so that the last 6 or 8 inches i s at a right angle to the re st. Step 5. Insert the bent part in t o the 1-inch hole you just drilled and pro be t o the le f t and the ri ght to confirm that a joist is no ...

  • M&S Systems WG100W - page 18

    Step 10. Follow the instructions included with the volume control and amplifier. Step 11. You are now ready to ins tall the speaker. Remove the paint m ask from the b affle. Be careful not to touch the speaker cones and tweeter when r emoving t he paint mask in order to prevent any damage. Atta ch th e speaker cable to t he speaker by pressing down ...

  • M&S Systems WG100W - page 19

    pattern you must posi tion the line in the tweeter in a horizontal position. See figure 5 on page 10. The combination of switch s ettings allow you to boost and cu t bass an d treble +/-3dB. Adju st the speaker level to accommodate for ro om acoustics. See figure 6 on page 10. Step 13. Divide each adhesive bead strip in h alf. (Adhesive bead strips ...

  • M&S Systems WG100W - page 20

    W hen t he s ound is sharper and more flat sounding, y ou are close or over a stud. • Identify studs by the position of electrical outlets or switches. T here may be a stud directly to the le f t or r ight of the se electrical fixture. This gives y ou a point of measurement since studs are either 24 or 1 6 inches on center in newer houses, 12 in ...

  • M&S Systems WG100W - page 21

    you do not cut the hole larger t han the outline. Step 7. Be sure to clear any in sulation material from the speaker back. Step 8. After y ou have determined the speaker locations secure a 16 gauge 2 conductor cable to the stud using an insulated staple. Leave at least 18 inches of additional cable f or connection during final speaker installation. ...

  • M&S Systems WG100W - page 22

    none of the strands from the black and red w ires are touching each other. This can create a short circuit that can damage your electronics. Mount the ba ffle to the frame u sing the 6 screw s provided. Do not over tighten the mounting screw s. Step 12 . After the speaker is mounted, adjustments to the s wiv el tweeter (small speaker) can be made b ...

  • M&S Systems WG100W - page 23

    Page 23 WAR R AN T Y M&S Systems ™ Limited 10-Year Warranty for WG Series Speakers and AirVac ™ Gold Power Units M&S Systems offers a 10-Year Warranty on our WG Series speakers and AirVac™ Gold power uni ts. This warranty is identical to the M&S Systems™ 2-Year Warranty, with the exception that this warranty covers the W G Serie ...

  • M&S Systems WG100W - page 24

    800.421.1 587 www .mssystems.com Service & T roubleshooting M&S Systems is committed to producing high quality audio products for the home. If you have any questions or problems with the speaker systems or the sy st em is not operating properly, contact your W G Seri es installer or call M&S Systems at (800) 366-9422. 115986 D 115986D.p ...

メーカー M&S Systems カテゴリー Speaker

M&S Systems WG100Wのメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- WG100Wの取扱説明書
- M&S Systemsの製品カード
- パンフレット
- またはM&S Systems WG100Wの消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、M&S Systems WG100Wの取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、M&S Systems WG100Wの取り付け説明書、サービスマニュアル、簡易説明書、またはM&S Systems WG100Wのユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、M&S Systems WG100Wの製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

M&S Systems WG100Wデバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがM&S Systems WG100Wを使用するのを助ける技術的文書のことです。説明書は通常、全てのM&S Systems WG100Wユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

M&S Systemsの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. M&S Systems WG100Wの説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははM&S Systems WG100Wの目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。M&S Systems WG100Wに関してこのドキュメントで見つけることができる全てのヒントの目次
3. M&S Systems WG100Wデバイスの基本機能を使うにあたってのヒント。 M&S Systems WG100Wのユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。M&S Systems WG100Wに関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるM&S Systems WG100Wのメーカー/サービスへの連絡先に関する情報。

M&S Systems WG100Wについてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもM&S Systems WG100Wの問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがM&S Systems WG100Wで同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)