-
Snapper 1695163 - page 1
A TT A CHMENT OPERA T OR’S MANU AL Clean Sweep T win Catcher Mfg. No. Description 1695163 Clean Sweep Twin Catcher 1733419 Rev. 00 Rev. Date 05/2006 TP 100-4296-00-AT-SMA Clean Sweep T win Catcher ...
-
Snapper 1695163 - page 2
...
-
Snapper 1695163 - page 3
1 Safety Rules & Inf ormation General W ar nings ............................................2 Saf ety Decals ..................................................2 General Operating Instructions Bef ore Operation .............................................3 Mowing with the Catcher .................................3 After Operation ............. ...
-
Snapper 1695163 - page 4
2 Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. The triangle in text signifies important cautions or warnings which must be followed. SAFETY DECALS This uni ...
-
Snapper 1695163 - page 5
Bef ore Operation Clear the lawn of all sticks, stones, wire and other debris which may be caught or thrown by the mower blades. Check grass condition. If wet, wait until later in the day. If grass is wet, the grass catcher is likely to become plugged. For efficient bagging, air circulation under the mower deck, through the chute and into the bag i ...
-
Snapper 1695163 - page 6
Initial Installation 4 Before beginning any service work turn off the PTO, set the parking brake, turn off the ignition, and disconnect the spark plug wire(s). W ARNING Figure 1. Install Spacer (left side shown) A. Speed Nut, 5/16-18 B. Threaded Side C. Square Hole D. Shoulder Bolt, 5/16-18 E. Rear Frame Support B C D A A E Initial Installation Hit ...
-
Snapper 1695163 - page 7
5 Baffle Installation Baffle and Blade Installation Note: Units with an anti-blowout baffle do not require the Clean Sweep baffle. 1. Remove mower deck. See OPERATOR’S MANUAL. 2. Install notched side of baffle (A, Figure 3) to discharge side of deck securing with 5/16-18 x 2 carriage bolt (C) and 5/16-18 locknut (D). Install 5/16-18 wing nut (F) ...
-
Snapper 1695163 - page 8
6 Puck Installation Figure 6. Install Pin and Bracket A. Lower Chute B. Locknut, 1/4-20 C. Puck, Metal D. Capscrews, Thin Head, 5/16-18 x 3/4 E. Locknuts, 5/16-18 F. Bracket A C F G D D E Component Installation BRACKET AND PIN INSTALLATION ON LOWER CHUTE 1. Secure the puck (C, Figure 6) to lower chute (A) using 5/16-18 x 3/4 capscrew (D) and 5/16-1 ...
-
Snapper 1695163 - page 9
7 Channel Installation Figure 8. Install Channel Assembly A. Channel Assembly B. Hitch C. Pin C B INSTALL CHANNEL ASSEMBLY AND “U”-TUBE 1. Slide the channel assembly (A, Figure 8) into hitch (B) as shown. 2. Install the pin (C) into the right side of hitch (B) and turn pin (C) counterclockwise to lock in place. 3. Install the “L” channel (E ...
-
Snapper 1695163 - page 10
8 Cover Installation A Figure 11. Install Cover to Channel Assembly A. Cover B. Pin C. Hair Pin D. Channel Assembly C B INSTALL COVER TO CHANNEL ASSEMBLY 1. Set the cover (A, Figure 11) on channel assembly. Slide pin (B) through hinge on cover and channel assembly (D) securing with hair pin (C). INSTALL CLIP TO BAG ASSEMBLY 1. Slide the white bar ( ...
-
Snapper 1695163 - page 11
Install Latch & Hinge 9 A F B Figure 14. Install Lower Discharge Chute 3A. Lower Chute B. Wing Nut C. Rubber Strap D. Carriage Bolt E. Discharge Deflector F. Deflector Hinge Rod G. Bracket LOWER DISCHARGE CHUTE INSTALLATION 1. Lift discharge deflector up (D, Figure 14). 2. Slide the notch of bracket (G) on to deflector hinge rod (F). 3. Secure ...
-
Snapper 1695163 - page 12
Normal Removal & Installation 10 Normal Remo val & Installation Collector Installation Note: See previous pages for more detailed installation and operation instructions if necessary. 1. Lift discharge deflector up (E, Figure 16). 2. Slide the notch of bracket (G) on to deflector hinge rod (F). 3. Secure the front of lower chute (A) to carr ...
-
Snapper 1695163 - page 13
Normal Removal 11 A. Channel Assembly G. Tubes B. Cover H. Boot C. Pin I. Puck D. Hitch J. Discharge Tube E. Bag K. Wire Form F. White Bar L. Seal E D B Figure 17. Normal Installation & Removal C L A G Collector Remov al 1. Disconnect the discharge tube (J, Figure 17) from boot (H) by moving wire form (K) up and out from metal puck (I). Remove ...
-
Snapper 1695163 - page 14
Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.MasseyLawn.com © Copyright 2006 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. Simplicity Mfg. Inc. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.AGCOLawn.com MANUFACTURING, INC. Simplicity Mfg. Inc. 500 N Spring Stre ...
Snapper 1695163についてご質問がありますか?
次のフォームを使用してください
見つけた説明書を読んでもSnapper 1695163の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがSnapper 1695163で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。