Taylor 220の取扱説明書

40ページ 0.74 mb
ダウンロード

ページに移動 of 40

Summary
  • Taylor 220 - page 1

    Model 2 20 Batch F reezer Opera ting Instr uctions 028763 - - M 5/99 (Or i ginal Publ icat ion) (Up da ted 8 /6/1 2 ) ...

  • Taylor 220 - page 2

    Com plete this pa ge for quic k refe renc e when ser vice i s requi re d: T aylor Distri butor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor mati on found on the data la bel: Model Number: Seri al Number: Electrical S pecs: V oltage Cycle Phase Maximum Fuse Si ze: A Minimum Wi re Ampaci ty: A E May, 1999 Tay lor All right s res erv ...

  • Taylor 220 - page 3

    Model 2 20 T able of Conte nts T able of Contents Section 1 T o the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 ....................................................... Air Cool ed Units 1 ..................................................... ...

  • Taylor 220 - page 4

    T able of Conte nts Mode l 220 T able of Contents - - P age 2 Drawing P roduct 20 ...................................................... Closing P rocedures 20 ................................................... Rinsing 20 .............................................................. Cleaning/S anitizing 21 ........................................ ...

  • Taylor 220 - page 5

    1 Model 2 2 0 T o the Installer 081208 Section 1 T o th e Installer The f ollowing are general inst allation inst ruct ions. For complet e inst allation det ails, pleas e see the c heck out card. Installer Safety In all ar eas of t he world, equipment should be installed i n acc ordance wit h existing local codes. Please c ontact your loc al author ...

  • Taylor 220 - page 6

    2 Model 2 2 0 T o the Installer 120806 Air Cooled Units DO NOT obst ruc t air int ake and disc harge openings: Air cooled units r equire a minimum of 3” (76 mm ) of clearanc e around all s ides of the fr eezer and 7 - - 1/ 2” (191 m m) on the bott om to allow for adequat e air f low acros s the c ondenser(s ). Inst all the def lect or provided ...

  • Taylor 220 - page 7

    3 Model 2 2 0 T o the Installer 120806 S Stat ionary appliances which ar e not equipped with a power cord and a plug or another device to dis connect the applianc e from the power s ource m ust hav e an all-pole disconnec ting devic e with a cont act gap of at least 3mm ins talled in t he ext ernal installat ion. S Appliances t hat are perm anently ...

  • Taylor 220 - page 8

    4 Model 2 2 0 T o the Operator 08091 1 Sec tion 2 T o the Ope rator The f reezer you have pur chased has been carefully engineered and manuf act ured t o give you dependable operat ion. Y our T aylor freezer, when properly operated and cared f or , will produc e a consis tent quality product . Like all mec hanical product s, this machine will requi ...

  • Taylor 220 - page 9

    5 Model 2 2 0 Safety 120806 Se cti on 3 Sa fety We, at T aylor Company , are concerned about the safet y of t he oper ator when he or she c omes in cont act with t he fr eezer and its parts. T ay lor has gone to extr eme effor ts t o design and m anufact ure built - - in saf ety f eatur es to pr otec t bot h you and the service technic ian. A s an ...

  • Taylor 220 - page 10

    6 Model 2 2 0 Safety 08091 1 S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screw s. S DO NOT rem ove any int ernal operat ing part s (examples: f reezer door, beater , scr aper blades, et c.) unles s all control switc hes are in t he ...

  • Taylor 220 - page 11

    7 Mo del 220 Op erato r Parts I den ti ficat io n Section 4 Operator Parts Identif ication ITE M DESCRIPTI ON P ART NO. 1 PAN-DRI P 027503 2 COVER A.- HOPPER-110- 220 X24778 3 GASKET-HOPPER COVER 011412 4 PANEL-REAR 031749 5 FUNNEL A.- MIX X35636 6 L O U V E R - S I D EL&R 019566 7 PANEL-UPPER SI DE R. 033125 8 PANEL A.- SIDE * RIGHT* X49481 9 ...

  • Taylor 220 - page 12

    8 Model 2 2 0 Op erato r Parts I den ti ficat io n Beater Door A ssembly ITE M DESCRIPTI ON P ART NO. 1 ROD A.- DRAW X30079 2 HOLDER A.- BEARING X30078 3 O-RI NG-2- 1/8 OD X . 139W- #225 020051 4 PISTON- VALVE 030083 5 PIN- HINGE X04329 6 PIN A. -PIVOT X34737 7 DOOR A.- PARTIAL SPOUT X32938 8 CAP A.- COVER X29667 ITE M DESCRIPTI ON P ART NO. 9 O-RI ...

  • Taylor 220 - page 13

    9 Mo del 220 Op erato r Parts I den ti ficat io n Accessor ies ITE M DESCRIPTI ON P ART NO. 1 PAIL- MIX 10 QUARTS 013163 2 B R U S H - M I XT A N KB O D Y3 ” X 7 ” 023316 3 BRUSH-DRAW VALVE 1- 1/2”X3” 014753 4 BRUSH-REAR BRG 1” X2”X14” 013071 ITE M DESCRIPTI ON P ART NO. 5 LUBRICANT- TAYLOR 047518 6 SANITI ZER KAY-5 125 PKTS. 041082 7 ...

  • Taylor 220 - page 14

    10 Model 2 20 Im porta nt: T o the Opera tor Section 5 Important: T o the Operator Figur e 1 ITE M DESCRIPTI ON 1 Control S witc h (Swit ch - - Rocker ) 2 Dial Light (Light - - O range - - Round) 3 T emperat ure Cont rol (Cont rol - - T emp. ) Sym bol Defi nitions T o bet ter communic ate in the Int ernat ional ar ena, t he words on many of our ope ...

  • Taylor 220 - page 15

    11 Model 2 2 0 O perati ng P roced ures Section 6 Operating Procedures The Model 220 f reezer can produce all flavors of ice cream , including t hose wit h fr uits and nut s. The freezer is designed for f illing pints, quarts or gallons to be placed in a hardening c abinet. T he unit has a 10 quart (9.5 lit er) mix hopper . The M odel 220 will pr o ...

  • Taylor 220 - page 16

    12 Model 2 2 0 Op erati ng Pro cedu res Step 2 In stal l th e b eater assembl y . F irs t chec k t he scr aper blades for any nic ks or signs of wear. If t he blades are in good conditi on, place the rear scr aper blade into the grooves on t he beater ( knif e edge t o the out side). T he pins on the blades f it under t he pins on t he beater t o p ...

  • Taylor 220 - page 17

    13 Model 2 2 0 O perati ng P roced ures Slide the o - - ring int o the groov e on the bearing holder, and lubricat e. Figur e 9 Lightly lubricate t he draw r od, and slide t he bearing holder ont o the rod, locking s tem f irs t. Figur e 10 Thr ead the valv e piston on t he end of the draw rod until tight . Figur e 1 1 Lightly lubr icat e the insid ...

  • Taylor 220 - page 18

    14 Model 2 2 0 Op erati ng Pro cedu res T urn t he bear ing holder so the holes ar e aligned wit h the holes in the v alve body . Sec ure wit h t he keeper pin. Figur e 15 Step 4 Insta ll the fr ee zer door . Align t he hole in the cros s bar with t he hole in either hinge, and inser t t he hinge pin. The c ross bar c an be assem bled for eit her r ...

  • Taylor 220 - page 19

    15 Model 2 2 0 O perati ng P roced ures 08091 1 Step 7 In stal l th e sh elf. Choose the level desired and align the groov es in the back of the shelf with t he holding collars . Slide t he shelf down over t he holding collars of the s ame height on t he left and right sides. Figur e 20 Sani tizing Step 1 Prepar e a pail of approv ed 100 PPM s anit ...

  • Taylor 220 - page 20

    16 Model 2 2 0 Op erati ng Pro cedu res Figur e 25 Step 5 Place t he cont rol swit ch in the “EJECT” position. T his will cause t he sanit izing solut ion in the freez ing cylinder t o be agitat ed. A llow t o agitat e for f ive minut es. Figur e 26 Step 6 Place t he cont rol swit ch in the “OFF” position. Wit h an empt y mix pail beneath t ...

  • Taylor 220 - page 21

    17 Model 2 2 0 O perati ng P roced ures 060425 Prim ing Step 1 Place t he funnel in t he mix inlet hole at the rear of t he hopper . Turn the funnel t o the r ight or lef t s o that the opening in t he f unnel does not align wit h t he opening in the mix inlet hole. Figur e 29 Step 2 Pour 10 quar ts ( 9.5 lit ers) of FRESH mix into the hopper . T h ...

  • Taylor 220 - page 22

    18 Model 2 2 0 Op erati ng Pro cedu res Step 5 When f ull st rength m ix is flowing f rom the eject ion por t, push the dr aw r od back into the v alve body and lock into place. Figur e 32 Note: T he f unnel can be ret urned to it s closed position. Another meas ure of mix c an be poured into the hopper in r eadiness f or t he next bat ch while the ...

  • Taylor 220 - page 23

    19 Model 2 2 0 O perati ng P roced ures 060425 Step 8 T o add fr uits and nuts, plac e the cont rol swit ch in the “EJECT” position. T here are t wo ways t o add fruits and nuts, as f ollows: Fr uits and nut s can be added through t he m ix hopper funnel assembly . Use t he plunger to press the ingredient s down into t he fr eezing cy linder . ...

  • Taylor 220 - page 24

    20 Model 2 2 0 Op erati ng Pro cedu res Step 5 If t he sc ale does not have overr un gr aduations , t hen weigh one pint (1/ 2 liter ) of mix before f reezing. Draw a sample pint ( 1/2 lit er) of frozen pr oduct and lev el it off with a st raight edge. Step 6 Place t he pint ( 1/2 lit er) of pr oduct on t he sc ale and read the w eight. Divide the ...

  • Taylor 220 - page 25

    21 Model 2 2 0 O perati ng P roced ures 08091 1 Step 3 Put t he cont rol swit ch into t he “EJECT” position and allow the wat er t o agit ate f or approx imately one minut e. Step 4 Put t he cont rol swit ch int o the “OFF” posit ion. Hold a mix pail beneat h the ejec tion port . Step 5 T urn t he draw rod handle and pull towar d, opening t ...

  • Taylor 220 - page 26

    22 Model 2 2 0 Op erati ng Pro cedu res Note: T o remove o- - ring s, use a sin gle service towel to gr asp the o - - ring. Apply press ure in an upward direct ion until the o- - ring pops out of its gr oove. W ith the ot her hand, pus h the t op of t he o- - ring f orward. I t will roll out of the groove and can be easily rem oved. If t here is mo ...

  • Taylor 220 - page 27

    23 Model 2 20 Impor tant : Oper ator C hec klis t 051 101 Section 7 Important: Operator Checklist Dur ing Cleani ng and Sani tizing Cleaning and saniti zing schedules are gover ned by your S tat e or local regulator y agencies and must be followed acc ordingly . The f ollowing c heck point s should be s tres sed during the cleaning and s anitiz ing ...

  • Taylor 220 - page 28

    24 Model 2 20 Im porta nt: Ope ra tor Che ck list 080221 Winter Stor age If the place of business is to be closed dur ing t he winter mont hs, it is import ant to prot ect the freezer by following cert ain prec autions, par ticular ly if t he building is subjec t t o freez ing conditi ons. Disconnec t the f reez er from the m ain power source t o p ...

  • Taylor 220 - page 29

    25 Model 2 2 0 T r oubles hooting Guide Section 8 T roubleshooting G uide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 1. Unit will not run in t he “AUTO” posit ion. a. Unit is unplugged. a. Plug in wall rec eptacle. -- -- b. Circuit breaker is off . b. T urn the br eaker on. -- -- c. Unit is off on res et. c. Plac e contr ol swit ch in the “O ...

  • Taylor 220 - page 30

    26 Model 2 2 0 T r oubles hooting Guide PROBL EM PROBABLE CAUSE REMEDY PA G E REF . 7. Overrun is too low . a. The tem perat ure cont rol is set too cold. a. Adjust it ac cordingly . 10 b. Not enough air is blended into t he product . b. Place t he cont rol swit ch in the “EJEC T” posit ion to blend in more air. Continue blending unt il the des ...

  • Taylor 220 - page 31

    27 Mo del 220 Parts Rep lacemen t Sch ed ul e Section 9 Parts Replacement Schedule P ART DESCRIPTION EVERY 3 MONTHS EVER Y 4 MONTHS EVER Y 6 MONTHS ANNUALL Y QTY . Fr ont Bearing X 1 Scr aper Blades X 3 Drive S haft Seal X 1 Funnel O - - Ring X 1 Fr eezer Door O - - Ring X 1 Bearing Holder and V alve P iston O - - Ring X 2 Black B rist le Brush, 1? ...

  • Taylor 220 - page 32

    Section 10 Parts List + A vail able Separ at ely 28 Parts List Model 2 2 0 HP62 - - J5083472/Up DESCRI PTI O N P ART NUMBER QTY . WARR. CLASS REMARKS P ARTS UPDA T E BAR -CR OS S *220* 011740 1 103 +PIN A.-CROSSBAR HING E X04329 2 103 BEARING-R EAR SHELL *NICK.PLATE 031324 1 000 +GUIDE-DRIP SEAL 028992 1 000 +NUT-BRASS BEARING 028991 1 000 +WASHER- ...

  • Taylor 220 - page 33

    29 + A vail able Separ at ely Model 2 2 0 Parts List DESCRI PTI O N P ART S UPDA T E REMARKS W ARR. CLASS QTY . P ART NUMBER +CAPACITOR-START- 216- 259UF/330V 048908 1 103 208-230/60/1 +RELAY-START-COMPRESSOR 048909 1 103 208-230/60/ 1 CO NDE NSE R-A C-12LX 18HX4.3- 5RO W 019558 1 103 CO NTR OL- TEMP -15F T O 40F 019747 1 103 +KNOB- TEM P CONTROL 0 ...

  • Taylor 220 - page 34

    + A vail able Separ at ely 30 Parts List Model 2 2 0 DESCRI PTI O N P ART S UPDA T E REMARKS W ARR. CLASS QTY . P ART NUMBER BEARING-FR ONT * 110- 220* 019176 1 000 O- RING -1- 5/8 OD X .139W 018564 1 000 MIX F UNNEL O- RING -11- 3/8 OD X .103W 019046 1 000 O- RING -2- 1/8 OD X .139W- #225 020051 2 000 SEAL-DRIVE SHAFT 031316 1 000 TOOL-O-RIN G REM ...

  • Taylor 220 - page 35

    31 + A vail able Separ at ely Model 2 2 0 Parts List DESCRI PTI O N P ART S UPDA T E REMARKS W ARR. CLASS QTY . P ART NUMBER SCREW A.-CRO SSBAR X07233 1 103 SHAFT-BEATER * 220* 032276 1 103 +SEAL-DRIVE SHAFT 031316 1 000 SHE LF-DR IP TR AY* 121-26-31-220* 031753 1 103 SHE LL A.-IN SU LATED *220* X34861 1 512 STARTER-1 PHASE-4.5 TO 7 A 041950-27K 1 ...

  • Taylor 220 - page 36

    + A vail able Separ at ely 32 Parts List Model 2 2 0 DESCRI PTI O N P ART S UPDA T E REMARKS W ARR. CLASS QTY . P ART NUMBER +PLATE-SEAL * 220* 022783 1 103 +STEM * 220* 024842 1 103 WATER C OOLED ADAPTOR-3/8MP X 1/2BARB-BR 011021 2 103 BLOWER-100 CFM 012796-27 1 103 BRACKET-MOUNTING -WATER VALVE 038777 1 103 CONDENSER-WC-COAX 047540 1 103 GUARD-BL ...

  • Taylor 220 - page 37

    Model 2 2 0 030385 3/10 ...

  • Taylor 220 - page 38

    Model 2 2 0 030385 In set 3/10 ...

  • Taylor 220 - page 39

    Model 2 2 0 030385 - - 33 3/10 ...

  • Taylor 220 - page 40

    Model 2 2 0 030385 - - 62 3/10 ...

メーカー Taylor カテゴリー Refrigerator

Taylor 220のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 220の取扱説明書
- Taylorの製品カード
- パンフレット
- またはTaylor 220の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Taylor 220の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Taylor 220の取り付け説明書、サービスマニュアル、簡易説明書、またはTaylor 220のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Taylor 220の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Taylor 220デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがTaylor 220を使用するのを助ける技術的文書のことです。説明書は通常、全てのTaylor 220ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Taylorの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Taylor 220の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははTaylor 220の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Taylor 220に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Taylor 220デバイスの基本機能を使うにあたってのヒント。 Taylor 220のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Taylor 220に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるTaylor 220のメーカー/サービスへの連絡先に関する情報。

Taylor 220についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもTaylor 220の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがTaylor 220で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)