Leica 788472の取扱説明書

22ページ 4.93 mb
ダウンロード

ページに移動 of 22

Summary
  • Leica 788472 - page 1

    Leica DISTO TM E7400x The original laser distance meter ...

  • Leica 788472 - page 2

    Leica DISTO TM E7400x 788480a 1 EN Table of Contents Instrument Set-up - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2 Display - - - - - - - - - - - - - - - - - - - - - - - - ...

  • Leica 788472 - page 3

    Leica DISTO TM E7400x 788480a 2 EN Instrument Set-up Introduction The safety instructions and the user manual should be read through carefully before the product is used for the first time. The person responsible for the product must ensure that all users understand these directions and adhere to them. The symbols used have the following meanings: ...

  • Leica 788472 - page 4

    Leica DISTO TM E7400x 788480a 3 EN Instrument Set-up Display Horizontal measurement Units Stake out Ceiling area Wall area Circumference Measuring reference 2nd result Area / Volume Tilt angle Info Slope distance Addition / Subtraction Illumination Memory Timer Triangle area Battery Min/Max Measuring Indirect height Pythagoras Main line Insert batt ...

  • Leica 788472 - page 5

    Leica DISTO TM E7400x 788480a 4 EN Operations Switching ON/OFF Clear Message Codes ON OFF 2 sec Device is turned OFF. i Press ON but- ton 2 sec to st art continuous laser mode. 1x Undo last action. 2x Leave actual func- tion, go to de fault operation mode. If the message " InFo " appears with a number, observe the instructions in section ...

  • Leica 788472 - page 6

    Leica DISTO TM E7400x 788480a 5 EN Operations Multifunctional endpiece i The orientation of the endpiece is automaticall y detected and the zero point is accordingly ad- justed. Distance unit setting Tilt unit setting Switch between the following unit s: 0.000 m 0.0000 m 0.00 m 0.00 ft 0‘00‘‘ 1/32 0‘00‘‘ 1/16 0‘00‘‘ 1/8 0‘00‘? ...

  • Leica 788472 - page 7

    Leica DISTO TM E7400x 788480a 6 EN Operations Beep ON/OFF Illumination ON/OFF 2 sec simulta ne- ously 2 sec simultane- ously Keypad lock ON Keypad lock OFF 2 sec simulta ne- ously PRESS MINUS 1 withi n 2 sec 2 ...

  • Leica 788472 - page 8

    Leica DISTO TM E7400x 788480a 7 EN Measuring Functions Measuring single distance 1 Aim active laser at target. 2 8.532 m 3 i Target surfaces: Measuri ng errors can occur when measuring to col- ourless liquids, glass, styrofo am or semi-permeable surfaces or when aiming at high gloss surfaces. Against dark surfaces the measur- ing time increases. Pe ...

  • Leica 788472 - page 9

    Leica DISTO TM E7400x 788480a 8 EN Measuring Functions Area 1 1x 2 Aim laser at first target point. 3 4 Aim laser at sec- ond target point. 24.352 m 2 5 i The result is shown in the main line and the mea sured va lue above . Partial Measurements: Press + or - after starting the fir st measurement. Measure and add or subtract distances. Finish with ...

  • Leica 788472 - page 10

    Leica DISTO TM E7400x 788480a 9 EN Measuring Functions Volume 1 2x 2 Aim laser at first target point. 3 4 Aim laser at sec- ond target point. 5 6 Aim laser at third target point. 78.694 m 3 7 i The result is shown in the main line and the measured value above. 24.224 m 2 208.703 m 2 80.208 m 78.694 m 3 2 sec Circumference Wall areas Ceiling/floor a ...

  • Leica 788472 - page 11

    Leica DISTO TM E7400x 788480a 10 EN Measuring Functions Triangular area 1 3x 2 Aim laser at first target point. 3 4 Aim laser at sec- ond target point. 5 6 Aim laser at third target point. 24.352 m 2 7 33.852 m 24.352 m 2 40.8 ° 2 sec Angle included by the first two measurements Circumference Triangular area 8 ...

  • Leica 788472 - page 12

    Leica DISTO TM E7400x 788480a 11 EN Measuring Functions Pythagoras (3-point) 1 4x 2 Aim laser a t upper point. 3 4 Aim laser at rec- tangular point. 5 6 Aim laser at lower point. 8.294 m 7 i The result is shown in the main line and the measured distance above. Pressing the measuring key for 2 sec in the functi on activates auto- matically Minimum o ...

  • Leica 788472 - page 13

    Leica DISTO TM E7400x 788480a 12 EN Measuring Functions Pythagoras (partial height) 1 5x 2 Aim laser a t upper point. 3 4 Aim laser at 2nd point. 5 6 Aim laser at rec- tangular point. 2.602 m 7 i The result is shown in the main line and the measured distance above. Pressing the measuring key for 2 sec in the functi on activates au- tomatically Mi n ...

  • Leica 788472 - page 14

    Leica DISTO TM E7400x 788480a 13 EN Measuring Functions Stake out i Two different distances (a and b) can be entered to mark off de- fined measured lengths. 1 2 3 a b b a = b 1 2 3 a b b a = b 1 .000 m 1 6x 1. 01 2 m 2 Adjust value "a". 3 Approve value "a". 0.625 m 4 Adjust value "b". 5 Approve value "b" and ...

  • Leica 788472 - page 15

    Leica DISTO TM E7400x 788480a 14 EN Measuring Functions Smart Horizontal Mode 1 Aim laser at tar- get. 2 0.032 m 5.204 m 40.8 ° 4.827 m x z x y z y 3 (up to 360° and a transverse tilt of ±10°) i Press key again to switch off horizontal measure- ment. Height tracking i This function displays continously the tracking height if the device is turne ...

  • Leica 788472 - page 16

    Leica DISTO TM E7400x 788480a 15 EN Measuring Functions Memory (20 last displays) Delete Memory 8.294 m 20 20 last displ ays are displayed. 1 8.294 m 20 Navigates trough 20 last displays. 2 The value from the main line can be used for fur- ther calculations. 2 sec 3 2 sec simultaneously Memory is completely deleted. ...

  • Leica 788472 - page 17

    Leica DISTO TM E7400x 788480a 16 EN Calibration Calibration of tilt se nsor (Tilt Calibration) 1 2 sec simultane- ously 2 Place device on absolutely flat s urface. 3 180° 4 Turn the device ho rizontally by 180° and place it again on absolutely flat surface. 5 6 Place device on absolutely flat s urface. 7 180° 8 Turn the device ho rizontally by 1 ...

  • Leica 788472 - page 18

    Leica DISTO TM E7400x 788480a 17 EN Technical Data * applies for 100 % target refl ectivity (white painted wall), low background illumination, 25 ºC ** applies for 10 to 500 % target reflectivity, hi gh background illumination, - 10 ºC to + 50 ºC *** Tolerances apply from 0.05 m to 10 m with a confidence level of 95%. The maximum to lerance may ...

  • Leica 788472 - page 19

    Leica DISTO TM E7400x 788480a 18 EN Message Codes If the message Error does not disappear after switching on the device repeatedly, contact the dealer. If the message InFo appears with a number, press the Clear button and observe the following instructions: Care • Clean the device with a damp, soft cloth. • Never immerse the device in water. ? ...

  • Leica 788472 - page 20

    Leica DISTO TM E7400x 788480a 19 EN Safety Instructions Permitted use • Measuring distances • Tilt measurement Prohibited use • Using the product without instruction • Using outside the stated limits • Deactivation of safety systems and removal of explanatory and hazard labels • Opening of the equipment by using tools (screwdrivers, etc ...

  • Leica 788472 - page 21

    Leica DISTO TM E7400x 788480a 20 EN Safety Instructions FCC statement (a pplicable in U.S.) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reason- able protection against harmful interference in a residential installation.Thi ...

  • Leica 788472 - page 22

    Leica Geosystems AG CH-9435 Heerbrugg (Switzerland) www.disto.com Leica Geosystems AG, He erbrugg, Swit zerland has been certified as being equipped with a quality system which meets the International Standards of Quality Management and Quality Syst em s (ISO standard 9001) and Environ- mental Management Systems (ISO standard 14 001). Total Quality ...

メーカー Leica カテゴリー Laser Level

Leica 788472のメーカーから受け取ることができるドキュメントは、いくつかのグループに分けられます。その一部は次の通りです:
- #BRANDの図面#
- 788472の取扱説明書
- Leicaの製品カード
- パンフレット
- またはLeica 788472の消費電力シール
それらは全部重要ですが、デバイス使用の観点から最も重要な情報は、Leica 788472の取扱説明書に含まれています。

取扱説明書と呼ばれる文書のグループは、Leica 788472の取り付け説明書、サービスマニュアル、簡易説明書、またはLeica 788472のユーザーマニュアル等、より具体的なカテゴリーに分類されます。ご必要に応じてドキュメントを検索しましょう。私たちのウェブサイトでは、Leica 788472の製品を使用するにあたって最も人気のある説明書を閲覧できます。

関連する取扱説明書

Leica 788472デバイスの取扱説明書はどのようなものですか?
取扱説明書は、ユーザーマニュアル又は単に「マニュアル」とも呼ばれ、ユーザーがLeica 788472を使用するのを助ける技術的文書のことです。説明書は通常、全てのLeica 788472ユーザーが容易に理解できる文章にて書かれており、その作成者はその分野の専門家です。

Leicaの取扱説明書には、基本的な要素が記載されているはずです。その一部は、カバー/タイトルページ、著作権ページ等、比較的重要度の低いものです。ですが、その他の部分には、ユーザーにとって重要な情報が記載されているはずです。

1. Leica 788472の説明書の概要と使用方法。説明書にはまず、その閲覧方法に関する手引きが書かれているはずです。そこにははLeica 788472の目次に関する情報やよくある質問、最も一般的な問題に関する情報を見つけられるはずです。つまり、それらはユーザーが取扱説明書に最も期待する情報なのです。
2. 目次。Leica 788472に関してこのドキュメントで見つけることができる全てのヒントの目次
3. Leica 788472デバイスの基本機能を使うにあたってのヒント。 Leica 788472のユーザーが使い始めるのを助けてくれるはずです。
4. トラブルシューティング。Leica 788472に関する最も重要な問題を診断し、解決するために役立つ体系化された手続き
5. FAQ。よくある質問
6. 連絡先。一人では問題を解決できない場合に、その国におけるLeica 788472のメーカー/サービスへの連絡先に関する情報。

Leica 788472についてご質問がありますか?

次のフォームを使用してください

見つけた説明書を読んでもLeica 788472の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがLeica 788472で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。

画像のテキストを入力してください

コメント (0)