-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 1
1 Doc. No . Copyright © 1995 Cisco Systems, Inc. All rights reser ved. Cisco 7010 and Cisco 7505 Rac k-Mount and Cab le Management Kits Installation Instr uctions 78-1231-02 Cisco 7010 Product Number s: A CC-7010RMK= and A CC-7010CBLM= Cisco 7505 Product Number s: ACS/5-RMK= and A CS/5-CBLM= Customer Order Number: DOC-781231= This document contain ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 2
2 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instr uctions Product Overview Pr oduct Overview The Cisco 7010 is the fi ve-slot model in the Cisco 7000 series product line and the Cisco 7505 is the fi ve-slot model in the Cisco 7500 series. Figure 1 sho ws the interface processor end of the Cisco 7010 chassis. Not ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 3
Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions 3 Prerequisites The cable management kit includes two brackets and f asteners to secure the brackets to the inner sides of the interface processor end of the chassis. By routing cables through the brackets and a way from the interface ports, you can keep cables ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 4
4 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instr uctions Prerequisites Lifting Saf ely Whene ver you lift the chassis or any hea vy object, follow these guidelines: • A fully configured chassis weighs approximately 70 pounds. Whene ver possible, a void lifting the chassis by yourself. • Ensure that your foot ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 5
Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions 5 Prerequisites Equipment Racks Consider ations The rack-mounting hardware included with the router is suitable for most 19-inch equipment racks or T elco-type racks. The chassis mounts to two posts or rails in the rack with tw o mounting ears, which attach to ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 6
6 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instr uctions Prerequisites • If the rack has a vertical po wer strip or other obstacle, ensure that there is sufficient clearance to install and remov e processor modules. Allow at least 12 inches of clearance to pull the modules straight out of their slots. • When ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 7
Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions 7 Rack-Mounting the Chassis • Install and use the cable management brackets included with the router to keep cables or ganized and out of the way . Consider the equipment and cabling that is already installed in the rack. Ensure that cables from other equipme ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 8
8 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instr uctions Rack-Mounting the Chassis Figure 3 T ypical 19-Inch Equipment Rack P osts and Mounting Strips If you are installing a new router , mount the chassis in the rack before connecting any interf ace or po wer cables. Otherwise, disconnect all cables before movin ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 9
Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions 9 Rack-Mounting the Chassis Figure 4 Installing the Ears on the Chassis Step 4 While referring to Figure 4, turn the chassis so that the end that will be in the front of the rack is facing to ward you. F or example, Figure 4 sho ws the correct orientation for t ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 10
10 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instructions Rack-Mounting the Chassis Figure 5 Installing the Chassis in a Four-P ost, 19-Inch Rack W arning Install heavier equipment near the bottom of the rack to maintain a lo w center of gravity . A top-heavy rack could easily tip o ver if it is not anchored or bo ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 11
Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions 11 Rack-Mounting the Chassis T o install the chassis in the rack, follo w these steps: Step 1 On the chassis, ensure that all captiv e screws (on the processor modules and on the access cov er) are tightened. Step 2 Make sure that your path to the rack is unobs ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 12
12 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instructions Installing the Cable Management Brackets Installing the Cable Mana gement Brackets The cable management brackets attach to the inner sides of the chassis at the interface processor end. (See Figure 7.) Note For this procedure, the Cisco 7010 and Cisco 7505 ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 13
Cisco 7010 and Cisco 7505 Rack-Mount and Cable Management Kits Installation Instructions 13 Cisco Information Online Step 6 When connecting network interface cables, route each cable through the brack ets as sho wn in Figure 7. If you are using very thin cables that slip through the bracket openings, insert cable ties through the holes in the brack ...
-
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010 - page 14
14 Cisco 7010 and Cisco 7505 Rack-Mount and Cab le Management Kits Installation Instructions Cisco Information Online ...
Cisco Rack-Mount and Cable Mgmt. Cisco 7505/7010についてご質問がありますか？
次のフォームを使用してください
見つけた説明書を読んでもCisco Rack-Mount and Cable Mgmt. Cisco 7505/7010の問題を解決できない場合、下記のフォームを使用して質問をしましょう。ユーザーのどなたかがCisco Rack-Mount and Cable Mgmt. Cisco 7505/7010で同様の問題を抱えていた場合、その解決方法を共有したいと考えるかもしれません。